Page 1
FLAT WIDE DISPLAY FWD-50PX1 FWD-50PX1N FLAT PANEL DISPLAY SPEAKER SYSTEM SS-SP50FW TV STAND SU-50FW SERVICE MANUAL 1st Edition...
Page 2
Power cord plug should be pulled out from the wall before starting the service operation. If power switch is turned OFF only, you may receive an electric shock, because the unit may have an electric inside. Therefore, you should pull out the power cord plug from the wall before starting the service operation. FWD-50PX1...
Page 3
Hävitä käytetty paristo valmistajan ohjeiden Remplacer uniquement avec une batterie du même mukaisesti. type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. 1 (P) FWD-50PX1...
Page 4
For more information regarding recycling of re- chargeable batteries, call toll free 1-800-822-8837, or visit http://www.rbrc.org/ Caution: Do not handle damaged or leaking Lithium-Ion batteries. 2 (P) FWD-50PX1...
Section 1 Service Overview 1-1. Board Location S board X drive board Power unit board Digital video board S boards H2 board SP board Y drive board Interface board Q board B board U1 board H1 board (FWD-50PX1) FWD-50PX1...
When installing/removing the cabinet and replacing the board, place the unit on the conductive cushion. 1-2-1. Rear Cover Assembly 1. Loosen the two panel securing screws, then remove the U1 block assembly. (FWD-50PX1 only) 2. Remove the four screws (PSW M6 x 20), then remove the four nylon washers and four knobs.
Control button 3 x 8 H2 board Harness BVTP 3 x 8 Conductive cushion BVTP 3 x 8 Bezel assembly Harness Light tube H1 board 9. Attach the bezel assembly in the reverse order of steps 1 to 8. FWD-50PX1...
5. Remove the lithium battery from the battery holder on Harnesses the B board. Lithium battery (CR1220) Battery Q board holder CN7002 CN7001 B board CN1004 CN1005 CN1001 CN101 CN401 CN402 Harnesses 3 x 6 Flexible flat cable B board Harnesses Conductive cushion UL tapes FWD-50PX1...
S board S board Conductive cushion 4. Install the SP board in the reverse order of steps 1 to 3. Harness 3 x 6 S board 4. Install the S board in the reverse order of steps 1 to 3. FWD-50PX1...
Clampers QB block Conductive assembly cushion 3 x 6 Side frame Board cover Scan B board assembly Board holders Board holders Scan A board 10. Install the Y drive board in the reverse order of steps 1 to 9. FWD-50PX1...
Board holders 4. Install the X drive board in the reverse order of steps 1 to 3. Board holders Board holders 8. Install the digital video board and interface board in the reverse order of steps 1 to 7. FWD-50PX1...
K board bracket Connectors [B] Connector [B] assembly Harness Purse Conductive cushion Conductive locks cushion SP board Connectors [A] Harness Harnesses 14. Attach the power unit and DC fan in the reverse order of steps 1 to 13. Interface board FWD-50PX1...
(Refer to Section 1-2-1.) 2. Remove the connector and two screws, then remove the DC fan. Imprinting Connector DC fan 4 x 25 Conductive cushion 3. Attach the DC fan in the reverse order of steps 1 and 2. 1-10 FWD-50PX1...
PSW3 x 6 PSW3 x 6 Frame (H) PSW3 x 6 3 x 6 Frame (H) Side frame Conductive cushion Plasma display panel 13. Attach the plasma display panel in the reverse order of steps 1 to 12. 1-11 FWD-50PX1...
5. Attach the four knobs to the holes of the each stand. B board Unit Q board Knobs M6 x 20 Atacch the two knobs Q/B shield to the each stand. cover Bolt Knobs (M8 x 16) M6 x 20 Cushion 3 x 6 (15x25) Unit Unit Stands Stands 1-12 FWD-50PX1...
1-6. Packaging of the Plasma Display Panel When It Is Shipped to Pioneer Corporation Carton (Upper) Pad R (Upper) Pad L (Upper) Individual inner case Pad R (Under) Pad L (Under) POSITIONING SCREWS Carton (Under) PP bands FRONT LID Screws (12 pcs) SERVICE Individual inner case MODULE 1-13 FWD-50PX1...
The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 1-9. Warning on Power Connection Use the proper power cord for your local power supply. FWD-50PX1 United States, Continental United Kingdom, Ireland,...
The electrical adjustments can be performed using the remote White Balance When PDP is replaced. commander RM-980C supplied with the FWD-50PX1. The remote commander has the Service Mode. Select the Service Mode to perform the electrical adjustments as listed below.
Page 22
Table 1. It initializes the data unique to the machine and the common data (various setup values of the user menu). Do not carry out this command because it initializes the serial number and accumulative operation hours. FWD-50PX1...
Page 23
C Out Level Receive the NTSC signal and adjust color. The color adjustment of PAL and SECAM signals are performed in c) Sub Color upon completion of the NTSC signal adjustment. Adjustment range is from 0 to 63. FWD-50PX1...
Page 24
Adjustment range is from 0 to 255 for “Sub Cont Video” and “Sub Brt Video”, and from 0 to 63 for “Cb Refer to Section “2-3. White Balance Adjustment ”. Offset Video” and “Cr Offset Video”. AD Calibration Adjustment Refer to Section “2-4. AD Calibration Adjustment”. FWD-50PX1...
Page 25
It indicates the temperature that is measured by the S board attached on top of the power board. Temp3 : It indicates the temperature that is measured by the S board attached on the right side as viewed from backside. FWD-50PX1...
Page 26
EEPROM preset area No.2 is used for editing and the edited data is stored in the area No.11.) EEPROM System controller preset data area PROGRAM1 Editing RAM PROGRAM2 PROGRAM3 PROGRAM4 PROGRAM5 Editing PROGRAM6 PROGRAM7 PROGRAM8 PROGRAM9 PROGRAM10 PROGRAM11 PROGRAM12 FWD-50PX1...
Page 27
RAM. This mode is prepared for the case that the signal specification is already known. You can make adjust- ment and edit data of all items but the modified data are not reflected to the actual picture images. FWD-50PX1...
Page 28
This setup value becomes the default value of the user menu “Total H Pixel”. You should set in a way that number of H. Total Pixels is equal or more than sum of (H. Active Pixel +H. Sync Pixel +H. BP Pixel). FWD-50PX1...
Page 29
It sets the picture quality mode. Select the desired below. mode from “Standard”, “Vivid”, “User1”, “User2” or Wcp = Clamp Width/(Horizontal sync frequency x H. “User3”. Total Pixel) [seconds] This setting becomes the default value of the “Picture Mode” of user menu. FWD-50PX1...
Page 30
Insecure : Unstable frequencies. No Sync : Sync signal does not exist. If the same sync signal data exists within a preset area, the specification that has the smaller preset number has priority. 2-10 FWD-50PX1...
Page 31
P/S Temp : Temperature inside the power supply block is displayed. NO ACK DEV : Status whether the communication with the respective devices that are controlled by the C bus is established or not is displayed. 2-11 FWD-50PX1...
Page 32
3.3 V, analog system 6 V) error Power Off : Power-off sequence error e) Operation Time Accumulative operating hours are indicated. (In units of hour) f) Software Version Software version is indicated. g) PLD Version PLD version is indicated. 2-12 FWD-50PX1...
Page 33
Area 10 0x0A80 to 0x0A9F Reserved 0x0540 to 0x055F 0x0AA0 to 0x0ABF Reserved 0x0560 to 0x057F 0x0AC0 to 0x0ADF Reserved 0x0580 to 0x059F 0x0AE0 to 0x0AFF Reserved 0x05A0 to 0x05BF Reserved 0x05C0 to 0x05DF Reserved 0x05E0 to 0x05FF 2-13 FWD-50PX1...
Page 34
0x0FC0 to 0x0FDF 0x1540 to 0x155F 0x0FE0 to 0x0FFF 0x1560 to 0x157F Area 21 0x1000 to 0x101F Area 32 0x1580 to 0x159F 0x1020 to 0x103F 0x15A0 to 0x15BF 0x1040 to 0x105F 0x15C0 to 0x15DF 0x1060 to 0x107F 0x15E0 to 0x15FF 2-14 FWD-50PX1...
Page 35
0x1A40 to 0x1A5F 0x1FC0 to 0x1FDF 0x1A60 to 0x1A7F 0x1FE0 to 0x1FFF Area 10 0x1A80 to 0x1A9F 0x1AA0 to 0x1ABF 0x1AC0 to 0x1ADF 0x1AE0 to 0x1AFF Area 11 0x1B00 to 0x1B1F 0x1B20 to 0x1B3F 0x1B40 to 0x1B5F 0x1B60 to 0x1B7F 2-15 FWD-50PX1...
Page 37
59.995 YES P/P STANDARD 293M NORMAL 59.924 1235 35 1200 4 YES P/P STANDARD 293M NORMAL 60.000 YES P/N STANDARD 293M FULL 60.000 1125 101 1024 NO YES P/N STANDARD 293M FULL 56.000 YES P/N STANDARD 293M FULL 2-17 FWD-50PX1...
Page 39
60.000 STANDARD 293M NORMAL 60.000 STANDARD 293M NORMAL 50.000 STANDARD 293M NORMAL 60.000 STANDARD 293M NORMAL 50.000 STANDARD 293M NORMAL 59.940 STANDARD 293M NORMAL 59.940 YES N/N 30 STANDARD 293M NORMAL 59.940 YES N/N 64 STANDARD 293M NORMAL 2-19 FWD-50PX1...
2) Set [Cal Mode] of [AD Converter] of the Service Mode menu to [On]. 4) Set the video signal to the NTSC all gray 20 IRE. 5) Adjust [Sub Brt Video] until the G detection value becomes the setup value. (Setup value = 48 ± 2) 2-20 FWD-50PX1...
5. Repeat steps 3 and 4 until the detection values of R, G and B are within the range (± 2) of tolerance error. 6. Set [Cal Mode] of [AD Converter] of the Service Mode menu to [Off]. 2-21 FWD-50PX1...
10kΩ CN1003 CLOCK Make the cable as short as possible. Frequency counter 3. Select [Watch Error] in [General] of the Service Mode menu and enter the measurement result. 4. Set [32k Clock Out] to [Off]. 2-22 FWD-50PX1...
If no image appears when the above conditions are . CN8, 9: 6.5 V, 16.5 V, 220 V satisfied, the PDP unit is considered defective. . CN12: 6.5 V, 61 V . CN11: 3.3 V, 6.5 V . CN10: 12 V FWD-50PX1...
71dC, the shutting not be displayed any more. down is activated. At this time, the Standby indicator flashes to indicate that the PDP unit is in the error mode as shown in Section 3-1. FWD-50PX1...
Page 45
Bit 15 : Scan Converter (No Use for PFM) This model does not have the AV switch, therefore bit 2 always goes to 1 (high). This function detects the device containing error. It does not activate displaying the warning nor shutting-down operation. FWD-50PX1...
Page 46
(2) FTC VDET : Watch power voltage error (1.8 V or activated and this indication is stored in log less) after the PDP unit returns to the normal (3) RTC XSTOP : Watch oscillator error operation. FWD-50PX1...
Page 47
RTC VDET RTC XSTOP PDP Init DEC Init DC Init Power Off (1) Power Off : If the power-off sequence is not per- formed correctly, “NG” is displayed. Failure of the power supply block or the PDP is suspected. FWD-50PX1...
In this amplifier, each input signal is PWM modulated into square wave of about one hundred and several tens KHz and then output. The output signal is integrated through LPF that is constituted by L and C, and it drives the speaker as an analog waveform. FWD-50PX1...
OUTPUT Matrix and output. This Matrix is 3 x 3, that is, nine registers in total. The Hue control, Color control, etc. are enabled by calculating and changing the values using microcomputer. As for the RGB input, it is output as it is. FWD-50PX1...
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
3 x 20 3 x 8 3 x 6 3 x 6 3 x 6 3 x 6 3 x 6 FWD-50PX1 3 x 8 3 x 6 3 x 8 3 x 8 3 x 6 BVTP 3 x 8...
Page 55
Cover Block Part No. SP Description A-1062-627-A o MOUNTED CIRCUIT BOARD, Q A-1063-069-A o MOUNTED CIRCUIT BOARD, U1 (FOR FWD-50PX1) A-1070-525-A o MOUNTED CIRCUIT BOARD, B X-2022-899-1 s PANEL ASSY U1 (FOR FWD-50PX1) X-2022-906-1 s ASSY, REAR COVER X-2023-679-2 s ASSY, TERMINAL Q...
Page 56
3 x 6 4 x 35 3 x 6 BVTP 4 x 16 BVTP 4 x 16 BVTP 4 x 16 3 x 6 BVTP 4 x 16 BVTP 3 x 8 BVTP 3 x 8 BVTP 3 x 8 FWD-50PX1...
Page 57
9-885-061-45 s DIGITAL VIDEO BOARD 9-885-061-46 s INTERFACE BOARD 7-682-667-09 s SCREW,+PS 4X25(EP-FE/ZNBK/CM2) 7-682-947-01 s SCREW +PSW 3X6 7-682-948-09 s SCREW +PSW 3X8 7-682-961-01 s SCREW +PSW 4X8 7-682-969-09 s SCREW +PSW 4X35(EP-FE/ZNBK/CM2) 7-685-646-79 s SCREW +BVTP 3X8 7-685-663-71 s SCREW,+BVTP4X16 FWD-50PX1...
Page 58
A-1080-534-A s SPEAKER (50R) ASSY (RP) (FOR SS-SP50FW/W (PEARL WHITE)) A-1080-536-A s SPEAKER (50R) ASSY (RP) (FOR SS-SP50FW/S (SILVER)) A-1080-535-A s SPEAKER (50L) ASSY (RP) (FOR SS-SP50FW/W (PEARL WHITE)) A-1080-537-A s SPEAKER (50L) ASSY (RP) (FOR SS-SP50FW/S (SILVER)) 7-685-661-79 s SCREW,+BVTP4X12(EP-FE/ZNBK/CM2) FWD-50PX1...
Page 59
Overall SU-50FW Part No. SP Description 2-148-620-01 o REAR COVER 4-092-541-02 s FOOT FWD-50PX1...
1-131-661-11 s CAPACITOR,ELECT 100MF/10V CHIP 1-164-315-11 s CAPACITOR,CERAMIC 470PF/50V CH C230 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF 1-163-233-91 s CAPACITOR,CHIP CERAMIC 18PF/50 C231 1-126-392-11 s CAPACITOR,CHIP ELECT100MF/6.3V 1-126-394-11 s CAPACITOR,ELECT 10MF/16V(CHIP) C232 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C233 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF FWD-50PX1...
Page 61
1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C419 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C613 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C420 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C614 1-128-360-11 s CAPACITOR,ELECT 220MF/10V CHIP C421 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C615 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF FWD-50PX1...
Page 62
1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C844 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C1236 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C845 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C1238 1-164-315-11 s CAPACITOR,CERAMIC 470PF/50V CH C846 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C1239 1-107-682-11 s CAPACITOR,CHIP 1MF/16V (3216) 6-10 FWD-50PX1...
Page 63
8-759-082-61 s IC TC4W53FU 8-759-638-04 s IC Z8622912SSC-00TR C7245 1-126-392-11 s CAPACITOR,CHIP ELECT100MF/6.3V 8-752-053-21 s IC CXA1211M C7246 1-126-392-11 s CAPACITOR,CHIP ELECT100MF/6.3V C7247 1-126-392-11 s CAPACITOR,CHIP ELECT100MF/6.3V 8-752-390-35 s IC CXD2057M-T6 C7248 1-126-392-11 s CAPACITOR,CHIP ELECT100MF/6.3V 8-759-533-85 s IC L88M05T-FA-TL 6-11 FWD-50PX1...
Page 64
8-729-927-99 s TRANSISTOR 2SC4617R L208 1-412-052-21 s INDUCTOR, SMALL TYPE 1.00UH Q211 8-729-928-19 s TRANSISTOR 2SA1774R L401 1-412-052-21 s INDUCTOR, SMALL TYPE 1.00UH Q212 8-729-927-99 s TRANSISTOR 2SC4617R Q213 8-729-928-19 s TRANSISTOR 2SA1774R L601 1-412-058-11 s INDUCTOR,SMALL TYPE 10UH 6-12 FWD-50PX1...
Page 65
1-216-830-11 s RESISTOR,CHIP 5.6K 1/10W 1608 1-216-829-11 s RESISTOR,CHIP 4.7K 1/10W(1608) 1-218-694-11 s RESISTOR,CHIP 1.2K1/16W(1608) 1-216-821-11 s RESISTOR,CHIP 1.0K 1/10W(1608) 1-216-839-11 s RESISTOR,CHIP 33K 1/10W 1608 1-218-672-11 s RESISTOR,CHIP 150 1/16W(1608) 1-216-841-11 s RESISTOR, CHIP 47K 1/10W 1608 1-218-708-11 s RESISTOR,CHIP 4.7K 1/16W(1608) 6-13 FWD-50PX1...
Page 66
1-216-809-11 s RESISTOR,CHIP 100 1/10W 1608 R413 1-216-809-11 s RESISTOR,CHIP 100 1/10W 1608 R252 1-216-822-11 s RESISTOR, CHIP 1.2K 1/10W 1608 R414 1-216-817-11 s RESISTOR,CHIP 470 1/10W 1608 R255 1-218-853-11 s RESISTOR,CHIP 1.8K 1/10W(1608) R415 1-216-817-11 s RESISTOR,CHIP 470 1/10W 1608 6-14 FWD-50PX1...
Page 67
1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R1047 1-216-841-11 s RESISTOR, CHIP 47K 1/10W 1608 R626 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R1048 1-216-837-11 s RESISTOR,CHIP 22K 1/16W 1608 R627 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R1050 1-216-864-11 s CONDUCTOR, CHIP (1608) 6-15 FWD-50PX1...
Page 68
1-216-864-11 s CONDUCTOR, CHIP (1608) RB1211 1-234-371-11 s RES, NETWORK 47X4 (1005) R7287 1-216-864-11 s CONDUCTOR, CHIP (1608) RB1212 1-234-371-11 s RES, NETWORK 47X4 (1005) R7288 1-216-864-11 s CONDUCTOR, CHIP (1608) R7290 1-216-864-11 s CONDUCTOR, CHIP (1608) TH401 1-809-350-21 s THERMISTOR 6-16 FWD-50PX1...
Page 69
1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R8655 1-216-826-11 s RESISTOR,CHIP 2.7K 1/10W(1608) R8656 1-218-853-11 s RESISTOR,CHIP 1.8K 1/10W(1608) S8651 1-692-829-11 s SWITCH, TACTILE S8652 1-692-829-11 s SWITCH, TACTILE S8653 1-692-829-11 s SWITCH, TACTILE S8654 1-692-829-11 s SWITCH, TACTILE S8657 1-692-829-11 s SWITCH, TACTILE 6-17 FWD-50PX1...
Page 70
1-162-964-11 s CAPACITOR,CERAMIC 1000PF/50V B C3126 1-124-779-00 s CAPACITOR,ELECT 10MF/16V C3127 1-163-135-00 s CAPACITOR,CHIP CERAMIC 560PF C3066 1-162-964-11 s CAPACITOR,CERAMIC 1000PF/50V B C3128 1-127-573-11 s CAPACITOR,CERAMIC 1MFB(2012) C3067 1-162-964-11 s CAPACITOR,CERAMIC 1000PF/50V B C3129 1-127-573-11 s CAPACITOR,CERAMIC 1MFB(2012) 6-18 FWD-50PX1...
Page 71
D3011 8-719-800-76 s DIODE 1SS226 C3189 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF D3012 8-719-800-76 s DIODE 1SS226 C3190 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF D3013 8-719-800-76 s DIODE 1SS226 C3191 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF D3014 8-719-800-76 s DIODE 1SS226 6-19 FWD-50PX1...
Page 72
1-410-396-41 s FERRITE BEAD INDUCTOR (0.45UH) Q3010 8-729-927-99 s TRANSISTOR 2SC4617R FB3012 1-400-392-21 s INDUCTOR, FERRITE BEAD Q3011 8-729-041-37 s TRANSISTOR 2SJ377(TE16L) FB3013 1-400-392-21 s INDUCTOR, FERRITE BEAD Q3017 8-729-928-81 s TRANSISTOR DTC144EE FB3029 1-216-864-11 s CONDUCTOR, CHIP (1608) 6-20 FWD-50PX1...
Page 73
R3110 1-216-864-11 s CONDUCTOR, CHIP (1608) R3052 1-216-817-11 s RESISTOR,CHIP 470 1/10W 1608 R3111 1-216-829-11 s RESISTOR,CHIP 4.7K 1/10W(1608) R3112 1-216-829-11 s RESISTOR,CHIP 4.7K 1/10W(1608) R3053 1-216-805-11 s RESISTOR,CHIP 47 1/10W 1608 R3113 1-216-826-11 s RESISTOR,CHIP 2.7K 1/10W(1608) 6-21 FWD-50PX1...
Page 74
1-216-797-11 s RESISTOR,CHIP 10 1/10W 1608 R3183 1-216-864-11 s CONDUCTOR, CHIP (1608) R3184 1-216-797-11 s RESISTOR,CHIP 10 1/10W 1608 R3185 1-216-797-11 s RESISTOR,CHIP 10 1/10W 1608 R3186 1-216-797-11 s RESISTOR,CHIP 10 1/10W 1608 R3187 1-216-797-11 s RESISTOR,CHIP 10 1/10W 1608 6-22 FWD-50PX1...
Page 75
------- ----------------------- S BOARD U1 BOARD: FOR FWD-50PX1 ------- ----------------------- Ref. No. Ref. No. or Q'ty Part No. SP Description or Q'ty Part No. SP Description 3pcs A-1068-935-A o MOUNTED CIRCUIT BOARD, S A-1063-069-A o MOUNTED CIRCUIT BOARD, U1 C1501 1-126-392-11 s CAPACITOR,CHIP ELECT100MF/6.3V...
Page 90
DEMO COMB SYS CBL-IN BPF/ SECAM BELL FSC-OUT CRL-IN COLOR S DOUBLE SYSTEM SYNC TRAP V C/D CHROMA SEPA INTEC SEPA CHROMA AFC-FIL SYNC-GND CVBS/YC TRAP NOISE SELECT H C/D H VCO C1-IN (RGB1-IN) FC BUS CONTROL 8-10 8-10 FWD-50PX1...
Page 91
B (2/8) PQ07VZ012P (IC7003) B (5/8) PST3629NR (IC7002) Adaptive Vertical DGnd Enhancer Vertical-Dot PRCESSING DGnd memory DVcc mode ON/OFF EXCLUSIVE IC(STABILIZER, CLOUT – OVER CURRENT & CLKBUF HEAT PROTECTION, PAL N/M ON/OFF CONTROL) Vref PAL/NTSC CLOCK IBIPAS Comb/BPF 8-11 8-11 FWD-50PX1...
Page 92
B (4/8) TC74VHCT541AFT (IC1011) B (8/8) SN74LV123APWR (IC604) B (4/8) S-80828CNNB-B8NT2G (IC1005) B (4/8) S-80842CNNB-B83T2G (IC1020) DELAY B (7/8) SN74LV4053APWR (IC405) B (3/8) SI-3025LSA (IC201, IC202) IN (PTR) OPEN IN (MIC) VOUT 13 Z1 B (4/8) TC74VHCT14AFT (IC1012) OPEN OPEN 8-12 8-12 FWD-50PX1...
Page 93
CHAR CHARACTER ADDR GENERATOR MSGR DECODER SS CTR B (4/8), (6/8) TC7W241FU-TE12R (IC1009, IC1) OUTPUT I DRIVE LOGIC CONTROL & MUX LINE & FIELD SFLD CONTROL LINE & FID DECODES 17 3 2 18 VSS (A) RREF 8-13 8-13 FWD-50PX1...
Page 111
2 V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set 0.15 µ F 1.5 k Z voltmeter (0.75V) Earth Ground Fig A. Using an AC voltmeter to check AC leakage. FWD-50PX1...