1. Manuals
  2. Brands
  3. LG Manuals
  4. Cell Phone
  5. KG320
  6. Service manual

LG KG320 Service Manual

Hide thumbs Also See for KG320:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Service Manual
KG320
Date: May, 2006 / Issue 1.0

Advertisement

Table of Contents
loading

Related Manuals for LG KG320

Summary of Contents for LG KG320

  • Page 1 Service Manual KG320 Date: May, 2006 / Issue 1.0...

  • Page 2: Table Of Contents

    Table Of Contents 1. INTRODUCTION........5 4.11 Receiver Trouble ........85 4.12 Microphone Trouble.........87 1.1 Purpose ............. 5 4.13 RTC Trouble ..........89 1.2 Regulatory Information ....... 5 4.14 Camera and Flash Trouble ......91 1.3 Abbreviations ..........7 5. DOWNLOAD AND CALIBRATION..94 2. PERFORMANCE ........9 5.1 Download...........94 2.1 H/W Features..........9 2.2 Technical Specification ......10...
  • Page 3 - 4 -...

  • Page 4: Introduction

    1. INTRODUCTION 1. INTRODUCTION 1.1 Purpose This manual provides the information necessary to repair, calibration, description and download the features of this model. 1.2 Regulatory Information A. Security Toll fraud, the unauthorized use of telecommunications system by an unauthorized part (for example, persons other than your company’s employees, agents, subcontractors, or person working on your company’s behalf) can result in substantial additional charges for your telecommunications services.
  • Page 5 1. INTRODUCTION E. Notice of Radiated Emissions This model complies with rules regarding radiation and radio frequency emission as defined by local regulatory agencies. In accordance with these agencies, you may be required to provide information such as the following to the end user. F.

  • Page 6: Abbreviations

    1. INTRODUCTION 1.3 Abbreviations For the purposes of this manual, following abbreviations apply: Automatic Power Control Baseband Bit Error Ratio CC-CV Constant Current - Constant Voltage Digital to Analog Converter Digital Communication System dB relative to 1 milli watt Digital Signal Processing EEPROM Electrical Erasable Programmable Read-Only Memory Electrostatic Discharge...
  • Page 7 1. INTRODUCTION Power Amplifier Module Printed Circuit Board Programmable Gain Amplifier Phase Locked Loop PSTN Public Switched Telephone Network Radio Frequency Receiving Loudness Rating Root Mean Square Real Time Clock Surface Acoustic Wave Subscriber Identity Module Sending Loudness Rating SRAM Static Random Access Memory PSRAM Pseudo SRAM...

  • Page 8: Performance

    2. PERFORMANCE 2. PERFORMANCE 2.1 H/W Features Item Feature Comment Li-Poly, 600mAh × 24(H) × 6.5(T) [mm] Standard Battery Battery Size : 36 (W) Battery Weight : TBD Under the minimum current consumption environment Stand by Current (such as paging period 9), the level of standby current is below 4mA.

  • Page 9: Technical Specification

    2. PERFORMANCE 2.2 Technical Specification Item Description Specification EGSM TX: 890 + (n-1024) x 0.2 MHz RX: 935 + (n-1024) x 0.2 MHz (n=975~1024) Frequency Band TX: 1710 + (n-512) x 0.2 MHz RX: 1805 + (n-512) x 0.2 MHz (n=512~885) TX: 1810 + (n-512) x 0.2 MHz RX: 1905 + (n-512) x 0.2 MHz (n=512~885) RMS <...
  • Page 10 2. PERFORMANCE Item Description Specification GSM, EGSM Offset from Carrier (kHz). Max. dBc +0.5 600~ <1,200 1,200~ <1,800 1,800~ <3,000 3,000~ <6,000 Output RF Spectrum 6,000 DCS, PCS (due to modulation) Offset from Carrier (kHz). Max. dBc +0.5 600~ <1,200 1,200~ <1,800 1,800~ <3,000 3,000~ <6,000...
  • Page 11 2. PERFORMANCE Item Description Specification DCS, PCS Offset from Carrier (kHz). Max. (dBm) Output RF Spectrum (due to switching transient) 1,200 1,800 Spurious Emissions Conduction, Emission Status GSM, EGSM BER (Class II) < 2.439% @-102 dBm Bit Error Ratio DCS, PCS BER (Class II) <...
  • Page 12 2. PERFORMANCE Item Description Specification STMR 13 5 dB Stability Margin > 6 dB dB to ARL (dB) Level Ratio (dB) 17.5 22.5 30.7 Distortion 33.3 33.7 31.7 25.5 Side Tone Distortion Three stage distortion < 10% System frequency 2.5ppm (13 MHz) tolerance 32.768KHz tolerance 30ppm...
  • Page 13 2. PERFORMANCE Item Description Specification Forced shut down Voltage 3.35 0.03 V 1 Li-Poly Battery Standard Voltage = 3.7 V Battery Type Battery full charge voltage = 4.2 V Capacity: 800mAh Switching-mode charger Travel Charger Input: 100 ~ 240 V, 50/60 Hz Output: 5.2 V, 800 mA - 14 -...

  • Page 14: Technical Brief

    3. TECHNICAL BRIEF 3. TECHNICAL BRIEF 3.1 Transceiver (SI4210, U401) The RF parts consist of a transmitter part, a receiver part, a digitally-controlled crystal oscillator. The Aero® II transceiver is a complete RF front end for multi-band GSM and GPRS wireless communications.
  • Page 15 3. TECHNICAL BRIEF (1) Receiver Part The Aero II transceiver uses a digital low-IF receiver architecture that allows for the on-chip integration of the channel selection filters, eliminating the external RF image reject filters, and the IF SAW filter required in conventional superheterodyne architectures.
  • Page 16 3. TECHNICAL BRIEF The ADC output is downconverted to baseband with a digital quadrature local oscillator signal. Digital decimation and FIR filters perform digital filtering, and remove ADC quantization noise, blockers, and reference interferers. The response of the FIR filter is programmable to a flat pass band setting (FILTSEL = 0, Register 08h) and a linear phase setting (FILTSEL = 1, Register 08h).
  • Page 17 3. TECHNICAL BRIEF Figure. 3-3 SI4210 TRANSMITTER PART (3) Digitally-controlled crystal oscillator The Aero II transceiver integrates the DCXO circuitry required to generate a precise system reference clock using only an external crystal resonator. The DCXO replaces a discrete VC-TCXO module. The DCXO allows for the use of a standard 26 MHz crystal, which reduces both cost and area compared to using a VCTCXO module.
  • Page 18 3. TECHNICAL BRIEF The Aero II transceiver can be configured in DCXO mode or VC-TCXO mode by the XMODE pin. To use the transceiver in DCXO mode, the XMODE pin is tied high. The XTAL1 and XTAL2 pins are then connected directly to the 26 MHz crystal.

  • Page 19: Power Amplifier (Sky77328, U400)

    3. TECHNICAL BRIEF 3.2 Power Amplifier (SKY77328, U400) The RF parts consist of a transmitter part, a receiver part, a frequency synthesizer part, a voltage supply part, and a VCTCXO part. The SKY77328 Power Amplifier Module (PAM) is designed in a low profile (1.2 mm), compact form factor for quad-band cellular handsets comprising GSM850/900, DCS1800, and PCS1900 operation.
  • Page 20 3. TECHNICAL BRIEF Figure. 3-5 SKY77328 FUNCTIONAL BLOCK DIAGRAM - 21 -...

  • Page 21: 26 Mhz Clock (Vctcxo, X400)

    3. TECHNICAL BRIEF 3.3 26 MHz Clock (VCTCXO, X400) The 26 MHz clock(X501) consists of a TCXO(Temperature Compensated Crystal Oscillator) which oscillates at a frequency of 26 MHz. It is used within the SI4210, analog base band chipset (U101, AD6535ABCZ), digital base band chipset (U102, AD6527BABCZ). 2V75_VVCXO X400 R414...
  • Page 22 3. TECHNICAL BRIEF GND13 PCS_RX2 GND12 PCS_RX1 GND11 DCS_RX2 GND10 DCS_RX1 GND9 EGSM_RX2 GND8 EGSM_RX1 FL400 GND7 GND6 HWXQ511 GND5 GND4 GND3 DCSPCS_TX GND2 EGSM_TX GND1 ANT_SW1 (GPO_9) (GPO_11) ANT_SW2 C439 C440 270p 270p Figure 3-7 FEM CIRCUIT DIAGRAM - 23 -...

  • Page 23: Digital Main Processor (Ad6527B, U102)

    3. TECHNICAL BRIEF 3.5 Digital Main Processor (AD6527B, U102) Figure 3-5. SYSTEM INTERCONECTION OF AD6527 EXTERNAL INTERFACE - 24 -...
  • Page 24 3. TECHNICAL BRIEF • AD6527 is an ADI designed processor. • AD6527 consists of 1. Control Processor Subsystem • 32-bit ARM7TDMI Control Processor • 58.5 MHz operation at 1.7V • On-board 16KB instruction/Data Cache • 1 Mbits of on-chip System SRAM 2.
  • Page 25 3. TECHNICAL BRIEF 3.4.1 Interconnection with external devices A. RTC block interface Countered by external X-TAL The X-TAL oscillates 32.768KHz B. RF interface The AD6527B control RF parts through PA_BAND, ANT_SW1, ANT_SW2, ANT_SW3 , CLKON , PA_EN, S_EN, S_DATA, S_CLK, RF_PWR_DWN. Signals Description PA_BAND (GPO 17)
  • Page 26 3. TECHNICAL BRIEF C. SIM interface The AD6527B provides SIM Interface Module. The AD6527B checks status periodically during established call mode whether SIM card is inserted or not, but it doesn't check during deep Sleep mode. In order to communicate with SIM card, 3 signals SIM_DATA, SIM_CLK, SIM_RST(GPIO_23) are required.
  • Page 27 3. TECHNICAL BRIEF 3.4.2 AD6527B Architecture Figure 3-7. AD6527B Architecture The internal architecture of AD6527B is shown above Figure 3-7. AD6527 regroups three main subsystems connected together through a dynamic and flexible communication bus network. It also includes onboard system RAM (SRAM) and interfaces with external Flash Memory, Baseband converter functions, and terminal functions like MMI, SIM and Universal System Connector (USC).

  • Page 28: Analog Main & Power Management Processor (Ad6535, U101)

    3. TECHNICAL BRIEF 3.5 Analog Main & Power Management Processor (AD6535, U101) Figure 3-8. AD6535 FUNCTIONAL BLOCK DIAGRAM - 29 -...
  • Page 29 3. TECHNICAL BRIEF • AD6535 is an ADI designed Analog Baseband processor. AD6535 covers the processing GMSK modulation interface, Aux ADC, Voice signal processing and Power Management. • AD6535 consists of 1. BB Transmit section • GMSK Modulation • I-channel & Q-channel Transmit DACs and Filters •...
  • Page 30 3. TECHNICAL BRIEF 3.5.1 Baseband Transmit Section 1. The AD6537B Baseband Transmit Section is designed to support GMSK for both single-slot and multi-slot application. 2. The AD6535 includes a digital GMSK modulator which is used for GSM application. The GMSK modulator uses a ROM lookup table to modulate the serial data stream ffrom the BSPORT.
  • Page 31 3. TECHNICAL BRIEF 3.5.3 Auxiliary Section 1. This section includes an Automatic Frequency Control(AFC) DAC, voltage reference buffers, an Auxiliary ADC, and light controllers. • AFC DAC: 13 bits 2. This section also contains AUX ADC and Voltage Reference • IDAC: 10 bits •...
  • Page 32 3. TECHNICAL BRIEF 3.5.4 Audio Section 1. The AD6535 Audio section supports communications and personal audio applications. 2. The Audio Section provides an audio codec with two digital-to-analog converter, a ring tone volume controller, a microphone interface, and analog input and output channels. Figure 3-12.

  • Page 33: Power Management

    3. TECHNICAL BRIEF 3.5.5 Power Management Figure 3-13. AD6535 POWER MANAGEMENT SECTION 1. Power up sequence logic 1. The AD6535 controls power on sequence 2. Power on sequence - If a battery is inserted, the battery powers the 8 LDOs. - Then if PWRONKEY is detected, the LDOs output turn on.
  • Page 34 3. TECHNICAL BRIEF Figure 3-14. AD6535 POWER MODE LOGIC 2. LDO Block 1. There are 8 LDOs in the AD6535. - VCORE : supplies Digital baseband Processor core and AD6535 digital core - VMEM : supplies external memory and the interface to the external memory on the digital baseband processor (1,8V or 2.8V, 150mA) - VEXT : supplies Radio digital interface and high voltage interface (2.8V, 170mA) - VSIM : supplies the SIM interface circuitry on the digital processor and SIM card (2.85V, 20mA)
  • Page 35 3. TECHNICAL BRIEF 3. Battery Charging Block 1. It can be used to charge Lithium Ion batteries. Charger initialization, trickle charging, and Li-Ion charging control are implemented in hardware. 2. Charging Process - Check charger is inserted or not - If AD6535 detects that Charger is inserted, the CC-CV charging starts. - Exception : When battery voltage is lower than 3.2V, the precharge(low current charge mode) starts firstly.

  • Page 36: Charging Ic (Isl6299, U205)

    3. TECHNICAL BRIEF 3.6 Charging IC (ISL6299, U205) Charging IC VUSBIN VCHARGE TP103 VBAT CRDL R207 U205 ISL6299 IMIN _PPR (GPIO 1) _CHG CHG_STAT ICDL USBON PGND CHG_EN (GPIO_0) 33K (1%) (ERHZ0000268) R209 VA201 R211 C217 C218 R210 C219 R208 100K 100K EVLC14S02050...
  • Page 37 3. TECHNICAL BRIEF Figure 3-17. BLOCKDIAGRAM Cradle Charge Current The cradle charge current is enabled by the EN pin only, the USBON pin has no control on the cradle charge current. The cradle charge current is programmed with the external resistor connected between the ICDL pin and the GND pin.
  • Page 38 3. TECHNICAL BRIEF Trickle Charge Current When the battery voltage is below the minimum battery voltage VMIN given in the electrical specification, the charger operates in a trickle/preconditioning mode, where the charge current is typically 14% of the programmed charge current for the cradle input. If power comes from the USB input, the trickle mode current is approximately 53mA.

  • Page 39: Camera Ic(Ait811T,U103)

    3. TECHNICAL BRIEF 3.7 CAMERA IC(AIT811T,U103) Figure 3-18. AIT811T APPLICATION BLOCKDIAGRAM - 40 -...
  • Page 40 3. TECHNICAL BRIEF Multimedia & Camera 2V8_MV 1V8_MV 2V8_AMV 2V8_AMV 2V8_VEXT VBAT 2V8_MV 1V8_MV C101 FB101 U101 R101 VOUT1 C109 100K C108 VOUT2 0.01u 0.01u C102 C103 C106 C104 C105 C107 C110 BGND 0.01u 0.1u MIC2211-GMYML 3V3_MULTI_USB C111 MULTI_USB- PUSBDN MULTI_USB+ PUSBDP PGPIO25...

  • Page 41: Midi Ic(Ymu787,U202)

    3. TECHNICAL BRIEF 3.8 MIDI IC(YMU787,U202) Figure 3-20. YMU787 BLOCKDIAGRAM - 42 -...
  • Page 42 3. TECHNICAL BRIEF C205 MIDI 100p R210 R209 C207 R211 1000p C208 R212 3.3K GPIO12 _MIDI_RST _RST C209 13MHz CLKI SPOUT2L SPK_N I2S_SCK BLCK SPOUT1L SPK_P C211 C210 I2S_WS LRCK SPOUT2R I2S_SDO SPOUT1R U202 C233 GPIO0 TXOUT YMU787 GPIO1 EXTOUT GPIO2 GPIO3 R222...
  • Page 43 3. TECHNICAL BRIEF CONTROL REGISTER;ROM/SRAM The Control register and ROM/SRAM are accessed from”Instantaneous write register”,”Delayed write register”, and “Instantaneous read register”in the intermediate register. In the control register, there is a register to control the following synthesizer mainly. The voice parameter for FM(GM 128 voices+DRUM 40 voices)and wave data for WT are stored in ROM.
  • Page 44 3. TECHNICAL BRIEF LED,VIBRATOR CONTROL It is possible to synchronize an LED and vibrator with a play, and to control. Asynchronous control With a play is also supported. It supports 3 color LED control and it is possible to display 7 colors In maximum. CLOCK GENERATING BLOCK This device supports a clock input ranging from 1.5Mhz to 27Mhz.

  • Page 45: Keypad Switches And Scanning

    3. TECHNICAL BRIEF 3.9 Keypad Switches and Scanning KEY PCB CONN VBAT 2V5_VMIC CN100 VBAT RPWRON PWRKEY KEY_ROW1 KEY_ROW2 KEY_ROW3 R101 KEY_ROW4 KEY_COL0 KEY_COL1 KEY_COL2 KEY_COL3 KEY_COL4 PWRKEY DE_TX KEY_LIGHT R102 DE_RX MIC_N MIC_P C101 LEFT MENU R118 KEY_ROW1 R119 KEY_ROW2 RIGHT SEND...

  • Page 46: Microphone

    3. TECHNICAL BRIEF 3.10 Microphone The microphone is placed to the front cover and contacted to main PCB. The audio signal is passed to AIN1P and AININ pins of AD6535. The voltage supply VMIC is output from AD6535, and is a biased voltage for the AIN1P.

  • Page 47: Headset Interface

    3. TECHNICAL BRIEF 3.12 Headset Interface FOR EAR-MIC 2V6_JACK 2V8_VEXT U305 MAX4684EBC_T R300 R302 1.5K R301 C300 MIDI_HP_L HEADSET_PATHSEL AUXIN EAR_MIC 0.1u C301 C302 MIDI_HP_R AUX_SPK_L COM1 HEADSET_SPK_L COM2 AUX_SPK_R HEADSET_SPK_R R307 AUXIP C317 C311 C312 Hook Detect 2V8_VEXT 2V6_JACK 2V8_VEXT 2V8_VEXT U300...

  • Page 48: Memory(Toshiba, U204)

    3. TECHNICAL BRIEF 3.13 MEMORY(TOSHIBA, U204) MEMORY (128 + 128NOR + 64PSRAM + 1G NAND) ADD01 DATA00 ADD02 DATA01 ADD03 DATA02 ADD04 DATA03 ADD05 DATA04 ADD06 DATA05 ADD07 DATA06 ADD08 DATA07 ADD09 DATA08 ADD10 DATA09 DQ10 ADD11 DATA10 ADD12 DQ11 DATA11 2V8_VMEM 2V8_VMEM...

  • Page 49: Bluetooth(Lbma-2C67B2,U202)

    3. TECHNICAL BRIEF 3.14 BLUETOOTH(LBMA-2C67B2,U202) ANT201 BLUETOOTH VBAT 2V8_VBT FEED SNGF0016701 U200 VOUT (GPIO 2) C200 0.01u BYPASS BT_EN LP3985IBLX-2.8 FL201 C202 C203 C204 C205 LFB212G45SG8A166 0.1u 2V8_VBT (GPIO 8) RESETB VDD_1_8V _BT_RST L200 VDD_DIG C207 VDD_VREGIN 2V8_VMEM 22nH PIO0 C208 C209 C210...

  • Page 50: Camera Connector, Camera Ldo(Cn202,U201)

    3. TECHNICAL BRIEF 3.15 CAMERA CONNECTOR, CAMERA LDO(CN202,U201) 2V8_CAM_AVDD 1V8_CAM 2V8_CAM_DVDD VCORE AGND R215 R216 CN202 4.7K 4.7K C_CD07 C_SCK C_CD06 C_SDA C_CD05 C_CD04 C_VS C_CD03 C_HS C_CD02 C_MCLK C_CD01 C_CD00 C_PCLK C_RST C229 FB202 0.1u ENBY0019101 Close to AVDD DGND Figure 3-28.

  • Page 51: Key Backlight

    3. TECHNICAL BRIEF 3.16 KEY BACKLIGHT Key Backlight Q300 KEY_LIGHT R318 2SC5663 KEY_BACKLIGHT R319 Figure 3-30. MAIN KEY BACKLIGHT 3.17 WHITE/FLASH LED LDO CAMERA FLASH LED FLASH LED & LCD Backlight VBAT FLASH_LED LD201 L101 FB102 R110 VOUT_FL FLASH_LED FB103 C127 VOUT_BL MLED...

  • Page 52: Flip Switch (U105)

    3. TECHNICAL BRIEF 3.18 FLIP SWITCH (U105) FLIP SWITCH 2V8_VEXT R114 100K CAM_COV_DET OUTPUT C130 C131 GND2 PGND GND1 0.01u U105 A3212EEH-T Figure 3-34. FLIP SWITCH 3.19 VIBRATOR The vibrator is placed in main board. The vibrator is driven from VIBRATOR from AD6527B. VBAT VBAT VIBRATOR...

  • Page 53: Trouble Shooting

    4. TROUBLE SHOOTING 4. TROUBLE SHOOTING 4.1 RX Trouble TEST POINT 26Mhz OSCILLATOR SKY7477328 SI4210 Figure 4-1 - 54 -...
  • Page 54 4. TROUBLE SHOOTING Checking Flow START HP8960 : Test mode 62 CH, 7 level setting (TCH) 62CH, -60dBm setting (BCCH) Spectrum analyzer setting Oscilloscope setting Check VCTCXO Check FEM & Mobile SW Check RX IQ Redownload SW or Do calibration again - 55 -...
  • Page 55 4. TROUBLE SHOOTING (1) Checking VCTCXO Circuit TEST POINT Checking Flow VCTCXO Circuit is OK VCTCXO Circuit is OK Check Pin 3. 26 MHzO.K? See next Page to check See next Page to check Refer to Graph 4 -1(b) ANT SW & Mobile SW ANT SW &...
  • Page 56 4. TROUBLE SHOOTING (2) Checking FEM & Mobile SW Waveform TEST POINT VC_EGSM VC_DCSPCS FEM Control GSM & DCS & EGSM Graph 4-2(a) CIRCUIT GND13 PCS_RX2 GND12 PCS_RX1 GND11 DCS_RX2 GND10 DCS_RX1 GND9 EGSM_RX2 GND8 EGSM_RX1 FL400 GND7 GND6 HWXQ511 GND5 GND4 GND3...
  • Page 57 4. TROUBLE SHOOTING Checking Flow For these 2 test case, No Call connection is needed Check SW400 Pin ANT,RF Changing SW400 Open with RF Cable connected. Check SW400 Pin ANT,RF Short Changing SW400 with No RF Cable Connected Check C439,C440 VC_EGSM :Low Changing the Board.
  • Page 58 4. TROUBLE SHOOTING (4) Checking RX IQ TEST POINT CIRCUIT C423 C426 Waveform Graph 4-4 Checking Flow Check C423,C426. Check if there is any Replace U401 Similar? Major difference Refer to graph 4-4 Redownload software and calibration again - 59 -...

  • Page 59: Tx Trouble

    4. TROUBLE SHOOTING 4.2 TX Trouble TEST POINT 26Mhz OSCILLATOR SKY7477328 SI4210 Figure 4-2 - 60 -...
  • Page 60 4. TROUBLE SHOOTING Checking Flow START HP8960 : Test mode 62 CH, 7 level setting (TCH) 62CH, -60dBm setting (BCCH) Spectrum analyzer setting Oscilloscope setting Check VCTCXO Check FEM & Mobile SW Check SIGNAL Check TX IQ Redownload SW or Do calibration again - 61 -...
  • Page 61 4. TROUBLE SHOOTING (1) Checking VCTCXO Circuit TEST POINT Checking Flow VCTCXO Circuit is OK VCTCXO Circuit is OK Check Pin 3. 26 MHzO.K? See next Page to check See next Page to check Refer to Graph 4 -6(b) ANT SW & Mobile SW ANT SW &...
  • Page 62 4. TROUBLE SHOOTING (3) Checking Ant SW & Mobile SW TEST POINT CIRCUIT Waveform VC_DCSPCS VC_EGSM GND13 PCS_RX2 GND12 PCS_RX1 GND11 DCS_RX2 GND10 DCS_RX1 GND9 EGSM_RX2 GND8 EGSM_RX1 FL400 GND7 GND6 HWXQ511 GND5 FEM Control EGSM GND4 GND3 DCSPCS_TX Graph 4-7(a) GND2 EGSM_TX GND1...
  • Page 63 4. TROUBLE SHOOTING Checking Flow For the test, TX Stand alone Mode is needed. (PL=5 for GSM, PL=0 for DCS) Check C439,C440 Check whether FEM Check VC1, VC2, VC3 Changing board Set as TX mode Rrefer to Graph4-6(a), 4-6(b) Rrefer to Table 4-3 Check RF Level of Pin10 : ~32.5dBm Go to 4.3.5 Checking PAM...
  • Page 64 4. TROUBLE SHOOTING (4) Checking PAM Control Signal TEST POINT CIRCUIT (GPO_17) R400 PA_BAND R401 (GPO_16) PA_EN R402 TX_RAMP C407 C408 C406 Waveform Graph 4-8 Checking Flow Check TX_RAMP and PA_EN Check if there is Check if there is Similar? Similar? Similar? Download S/W...
  • Page 65 4. TROUBLE SHOOTING (5) Checking TX IQ TEST POINT Waveform Graph 4-9 CIRCUIT C423 XOUT C426 Checking Flow Check if there is Any Major Difference Similar? Replace U401 Refer to Graph 4-9 Redownload the Software And calibrate - 66 -...

  • Page 66: Power On Trouble

    4. TROUBLE SHOOTING 4.3 Power On Trouble TEST POINT VCORE VMEM VMIC VSIM VABB VRTC VUSB VCXO VEXT Figure 4-3 CIRCUIT R100 BACK_BATT C113 VCORE1 VCORE2 C114 VMEM1 VMEM2 C115 0.1u VRTC C116 VSIM (1608) C117 2.2u VABB C118 VMIC C119 VVCXO C122...
  • Page 67 4. TROUBLE SHOOTING Checking Flow START Check Battery Voltage Charge or Change Battery > 3.35V ? Push power-on key Check the contact of power key And check the level change Or dome-switch of PWRKEY Check the voltage of Replace U101 The LDO outputs at U101 VCORE=1.8V VVCXO=2.75V...

  • Page 68: Charging Trouble

    4. TROUBLE SHOOTING 4.4 Charging Trouble TEST POINT R209 CIRCUIT Charging IC VUSBIN VCHARGE TP103 VBAT CRDL R207 U205 ISL6299 IMIN _PPR (GPIO 1) _CHG CHG_STAT ICDL USBON CHG_EN PGND (GPIO_0) 33K (1%) (ERHZ0000268) R209 VA201 R211 C217 C218 R210 C219 R208 100K...
  • Page 69 4. TROUBLE SHOOTING Checking Flow START Resolder the CN301 I/O Connector(CN301) Pin 12,13 : VCHARGE Is well-soldered ? Pin1,18,19,20,21,22 : GND Resolder the U205 are U205 well-soldered? Voltage across R209 is Replace theU205 about 1.2V? The battery may have Battery is charged? problems.

  • Page 70: Vibrator Trouble

    4. TROUBLE SHOOTING 4.5 Vibrator Trouble TEST POINT Figure 4-5 CIRCUIT VBAT VBAT VIBRATOR R202 R203 R206 Q201 EMZ2 R207 1.5K VIBRATOR (GPIO 3) CN201 D201 C206 R208 4.7u 1SS352-TPH3_F - 71 -...
  • Page 71 4. TROUBLE SHOOTING Checking Flow SETTING : Enter the engineering mode, and set vibrator on at vibration of BB test menu START Check connection vibrator Connect vibrator Check the soldering Is the voltage at pin 6 of R202. Resolder R202. of Q201 near 0V? Replace Q201 Check soldering D201...

  • Page 72: Lcd Trouble

    4. TROUBLE SHOOTING 4.6 LCD Trouble TEST POINT AIT811T EMI FILTER CN102 Figure 4-6 - 73 -...

  • Page 73: Circuit Diagram

    4. TROUBLE SHOOTING CIRCUIT DIAGRAM 2V8_AMV 2V8_MV 1V8_MV C101 C109 C108 0.01u 0.01u C102 C103 C110 0.1u 3V3_MULTI_USB C111 MULTI_USB- PUSBDN MULTI_USB+ PUSBDP PGPIO25 N_IO(2) VDD_IO3 PGPIO24 N_IO(1) GND_IO3 PGPIO23 N_IO(0) _LCD_CS _PHCS PGPIO22 _N_WP GPIO42 _PHRD PGPIO21 _N_WE C112 _PHWE PGPIO20 N_ALE...
  • Page 74 4. TROUBLE SHOOTING Checking Flow START Refer to Power is supplied to Power On Trouble the board? Connection between Reconnect FPCB and boards is OK? FPCB CN102 Re-solder the CN102 is soldered well? Paths of LCD control Change the AIT811T signals are OK?(AIT811T) Paths of LCD control Re-solder the EMI FILTER...

  • Page 75: Bt Trouble

    4. TROUBLE SHOOTING 4.7 BT Trouble TEST POINT U202 U201 U200 U203 Figure 4-7 CIRCUIT DIAGRAM ANT201 BLUETOOTH VBAT 2V8_VBT FEED SNGF0016701 U200 VOUT (GPIO 2) C200 0.01u BYPASS BT_EN LP3985IBLX-2.8 FL201 C202 C203 C204 C205 LFB212G45SG8A166 0.1u 2V8_VBT (GPIO 8) _BT_RST RESETB VDD_1_8V...
  • Page 76 4. TROUBLE SHOOTING Checking Flow Is BT_RST signal shape similar Replace U102 to Fig.1 during Powering on Bluetooth Replace U201 2V8_VBT at C204=2.8V BT_EN is 2.8V Bluetooth Power off Replace U200 Is DEBUG_TX signal similar to Replace U201 Fig.2 during Powering on Bluetooth? Is DEBUG_RX signal similar to Replace U202...
  • Page 77 4. TROUBLE SHOOTING Graph 4-10(a) BLUE-RST Graph 4-10(b) DEBUG_TX,RX Graph 4-10(c) PCM_SYNCS,TX,RX,USC0 - 78 -...

  • Page 78: Speaker Trouble

    4. TROUBLE SHOOTING 4.8 Speaker Trouble TEST POINT C211 C210 Figure 4-8 CIRCUIT DIAGRAM SPOUT2L SPK_N SPOUT1L SPK_P C211 C210 SPOUT2R SPOUT1R TXOUT - 79 -...
  • Page 79 4. TROUBLE SHOOTING Checking Flow START Check the state of contact of dual speaker Reassemble speaker C210,C211 Re-solder C210,C211 Well-soldered? Check U202 works properly Re-solder U202 Speaker Change main board Works properly? Speaker working! - 80 -...

  • Page 80: Sim Card Interface Trouble

    4. TROUBLE SHOOTING 4.9 SIM Card Interface Trouble TEST POINT Figure 4-9 CIRCUIT DIAGRAM SIM CONNECTOR 2V85_VSIM 2V85_VSIM R201 J201 SIM_RST (GPIO 23) SIM_DATA SIM_CLK GND2 GND1 C202 C201 C203 C204 1000p 220n - 81 -...
  • Page 81 4. TROUBLE SHOOTING Checking Flow START Change the SIM Card. Our phone Does the SIM cards supports only 3V SIM card. supports 2.85V ? Voltage Voltage at pin1 of Replace J201 or at VSIM of U101 check soldering of components J201 is 2.85V? Is 2.85V? Change the SIM Card...

  • Page 82: Earphone Trouble

    4. TROUBLE SHOOTING 4.10 Earphone Trouble TEST POINT U305 CN301 Figure 4-10 CIRCUIT DIAGRAM FOR EAR-MIC 2V6_JACK 2V8_VEXT U305 MAX4684EBC_T R300 R302 1.5K R301 C300 MIDI_HP_L HEADSET_PATHSEL AUXIN EAR_MIC 0.1u C301 C302 MIDI_HP_R COM1 AUX_SPK_L HEADSET_SPK_L AUX_SPK_R COM2 HEADSET_SPK_R R307 AUXIP C317 C311...
  • Page 83 4. TROUBLE SHOOTING Checking Flow START Resolder CN301 Does the audio Level at profile of the phone Replace CN301 JACK_DETECT signal change to the is low earphone mode? Set the audio part of the test equipment to Set the audio part of the test Change the earphone PRBS or continuous Equipment to echo mode...

  • Page 84: Receiver Trouble

    4. TROUBLE SHOOTING 4.11 Receiver Trouble TEST POINT Figure 4-13 CIRCUIT DIAGRAM RECEIVER VA100 C139 EVLC14S02050 OUT100 R108 R195 RCV_P AOUT1P AOUT1N C140 C141 AOUT2P1 R110 R196 RCV_N AOUT2P2 AOUT2N1 OUT101 C142 VA101 AOUT2N2 AOUT3L AUX_SPK_L AOUT3R AUX_SPK_R EVLC14S02050 C146 C147 C143 C144...
  • Page 85 4. TROUBLE SHOOTING Checking Flow SETTING : After initialize Agilent 8960, Test EGSM, DCS, PCS mode Set the property of audio as PRBS or continuous wave. Set the receiving volume of mobile as Max. START Check the soldering Re-solder the receiver receiver Check the signal level of Check the soldering...

  • Page 86: Microphone Trouble

    4. TROUBLE SHOOTING 4.12 Microphone Trouble TEST POINT C106 C118 R116 R105 R103,R104 Figure 4-14 CIRCUIT DIAGRAM R100 BACK_BATT C113 VCORE1 VCORE2 C114 VMEM1 VMEM2 CLOSE TO MIC C115 0.1u 2V5_VMIC VRTC C116 VSIM (1608) C117 2.2u VABB C118 VMIC R103 C119 VVCXO...
  • Page 87 4. TROUBLE SHOOTING Checking Flow SETTING : After initialize Agilent 8960, Test EGSM, DCS, PCS mode Set the property of audio as PRBS or continuous wave. Set the receiving volume of mobile as Max. START Check the soldering Re-solder the receiver receiver Check the signal level of Check the soldering...

  • Page 88: Rtc Trouble

    4. TROUBLE SHOOTING 4.13 RTC Trouble TEST POINT R105 X100 BAT201 Figure 4-15 CIRCUIT DIAGRAM NGPCS1 _MIDI_CS NAUXCS1 C129 _LCD_CS GPIO_42_NMAIN_LCD_CS GPIO_43_NSUB_LCD_CS X100 C128 1000p 13MHz CLKIN DBB_CLKON CLKON R105 OSCOUT OSCIN PWRON MC-146_7pF NRESET 32.768KHz C131 CHG_EN GPIO_0_IRDA_TX CHG_STAT GPIO_1_IRDA_RX D100 BT_EN...
  • Page 89 4. TROUBLE SHOOTING Checking Flow START Is the voltage level of BAT201 Charge or change BAT201. > 1.2V ? Check the voltage at Resolder R105 or 1,4 of X100 Replace X100 Change main board - 90 -...

  • Page 90: Camera And Flash Trouble

    4. TROUBLE SHOOTING 4.14 Camera and Flash Trouble U201 Camera Module CN202 Figure 4-17 - 91 -...
  • Page 91 4. TROUBLE SHOOTING Circuit Diagram 2V8_CAM_DVDD VBAT 1.3 Pixel CAMERA 2V8_CAM_AVDD 1V8_CAM VCORE FB201 U201 VOUT1 R219 CAM_PWR_EN VOUT2 C215 C216 C214 C217 BGND 0.01u MIC2211-GMYML 2V8_CAM_AVDD 1V8_CAM 2V8_CAM_DVDD VCORE AGND R215 R216 CN202 4.7K 4.7K C_CD07 C_SCK C_CD06 C_SDA C_CD05 C_CD04 C_VS...
  • Page 92 4. TROUBLE SHOOTING Checking Flow START Go to the LCD Trouble Does LCD work properly? Set the Camera button ON Check power U201 Check power 1.8V Change U201 1V8_CAM Check the 13MHz waveform? Change U103 Check U103 Check the C_PCLK Check the C_HS Check the C_VS Resolder CN202...

  • Page 93: Download And Calibration

    5. DOWNLOAD AND CALIBRATION 5. DOWNLOAD AND CALIBRATION 5.1 Download A. Download Setup Figure 5-1 describes Download setup Figure 5-1. Download Setup - 94 -...
  • Page 94 5. DOWNLOAD AND CALIBRATION B. Download Procedure 1. Run GSM Multi Download program and select Setting 2. Select Configuration from the menu and you may see this window. - 95 -...
  • Page 95 5. DOWNLOAD AND CALIBRATION 3. Press key to select DLL file and press Open KG320.dll 4. Press key to select the mot files 5. Select AlchemyData.mot and press open 6. Repeat step 4-5 to select CodeData.mot - 96 -...
  • Page 96 5. DOWNLOAD AND CALIBRATION 7. Check if the ADI option is set to Hermes 8. Press OK to end Configuration Select Rate - 97 -...
  • Page 97 5. DOWNLOAD AND CALIBRATION 9. Press START to execute download 10. Once downloading is started, press STOP button to keep from re-downloading after downloading is completed. - 98 -...

  • Page 98: Block Diagram

    6. BLOCK DIAGRAM 6. BLOCK DIAGRAM - 99 -...
  • Page 99 - 100 -...

  • Page 100: Circuit Diagram

    USB BOOT INT CLOCK KEY_COL2 KEYPADCOL2 USC4 USC4 Approved JEONG CHON BOK USB BOOT EXT CLOCK KEY_COL3 KEYPADCOL3 USC5 USC5 KEY_COL4 KEYPADCOL4 USC6 DRAWING Iss. Notice No. Date Name Ver 1.0 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 101 -...
  • Page 101 01/13 Designer JEONG YI SEON 2 / 4 2006 Checked JEONG YI SEON DRAWING BLUE TOOTH/CHARGING IC//MEMORY NAME Approved JEONG CHON BOK DRAWING Iss. Notice No. Date Name Ver 1.0 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 102 -...
  • Page 102 SIM_DATA JEONG YI SEON DRAWING KEY-FPCB CONN / SIDE KEY CONN NAME MM CONN / BtoB CONN JEONG CHON BOK C320 C319 DRAWING Iss. Notice No. Date Name Ver 1.0 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 103 -...
  • Page 103 ANT_SW2 2006 0.01u 4.7u GSM_TX HIGH Checked LEE JIN DRAWING HIGH DCS/PCS_TX RF(AERO II) NAME GSM_RX Approved JEONG CHON BOK DCS_RX PCS_RX DRAWING Iss. Notice No. Date Name Ver 1.0 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 104 -...
  • Page 104 01/13 Designer JEONG YI SEON 2006 Checked JEONG YI SEON 2006 KEY-FPCB DRAWING NAME KEY-FPCB(KEY, KEY-BACKLIGHT, MIC) Approved JEONG CHON BOK 2006 Ver 1.0 DRAWING Iss. Notice No. Date Name LG Electronics Inc. LG Electronics Inc. LGIC(42)-A-5505-10:01 - 105 -...
  • Page 105 JEONG YI SEON 2006 OUTPUT C130 C131 GND2 Checked PGND GND1 JEONG YI SEON DRAWING 0.01u UPPER-ADI U105 NAME A3212EEH-T Approved JEONG CHON BOK DRAWING Iss. Notice No. Date Name LG Electronics Inc. Ver 1.0 LG Electronics Inc. LGIC(42)-A-5505-10:01 - 106 -...
  • Page 106 JEONG YI SEON Close to AVDD 2 / 2 2006 DGND Checked JEONG YI SEON DRAWING UPPER-ADI NAME Approved JEONG CHON BOK DRAWING Iss. Notice No. Date Name Ver 1.0 LG Electronics Inc. LGIC(42)-A-5505-10:01 LG Electronics Inc. - 107 -...

  • Page 107: Pcb Layout

    8. PCB LAYOUT - 108 -...
  • Page 108 8. PCB LAYOUT - 109 -...
  • Page 109 8. PCB LAYOUT - 110 -...
  • Page 110 8. PCB LAYOUT - 111 -...
  • Page 111 8. PCB LAYOUT - 112 -...
  • Page 112 8. PCB LAYOUT - 113 -...
  • Page 113 - 114 -...

  • Page 114: Engineering Mode

    9. ENGINEERING MODE 9. ENGINEERING MODE A. About Engineering Mode Engineering mode is designed to allow a service man/engineer to view and test the basic functions provided by a handset. B. Access Codes The key sequence for switching the engineering mode on is 2945#*#. Pressing END will switch back to non-engineering mode operation.

  • Page 115: Bb Test [Menu 1]

    9. ENGINEERING MODE 9.1 BB Test [MENU 1] 9.1.1 LCD 1) COLOUR : WHITE, RED, GREEN, BLUE, BLACK 9.1.2 CAMERA This menu is to test the Camera. 1) Main LCD preview : It shows the picture on Main LCD. 2) Flash on : It turns on the Flash LED. 3) Flash off : It turns off the Flash LED.
  • Page 116 9. ENGINEERING MODE 9.1.6 ADC (Analog to Digital Converter) This displays the value of each ADC. 1) MVBAT ADC : Main Voltage Battery ADC 2) AUX ADC : Auxiliary ADC 3) TEMPER ADC : Temperature ADC 9.1.7 BATTERY 1) Bat Cal : This displays the value of Battery Calibration. The following menus are displayed in order : BAT_LEV_4V, BAT_LEV_3_LIMIT, BAT_LEV_2_LIMIT, BAT_LEV_1_LIMIT, BAT_IDLE_LI MIT, BAT_INCALL_LIMIT, SHUT_DOWN_VOLTAGE, BAT_RECHARGE_LMT...

  • Page 117: Rf Test [Menu 2]

    9. ENGINEERING MODE 9.2 RF Test [MENU 2] 9.2.1 SAR test This menu is to test the Specific Absorption Rate. 1) SAR test on : Phone continuously process TX only. Call-setup equipment is not required. 2) SAR test off : TX process off 9.3 MF mode [MENU 3] This manufacturing mode is designed to do the baseband test automatically.

  • Page 118: Trace Option [Menu 4]

    9. ENGINEERING MODE 9.3.7 MicSpk Test The sound from MIC is recorded for about 3 seconds, then it is replayed on the speaker automatically. 9.4 Trace option [MENU 4] This is NOT a necessary menu to be used by neither engineers nor users. 9.5 Call timer [MENU 5] This menu is to set the Digital Audio Interface Mode for Speech Transcoder and Acoustic testing.

  • Page 119: Stand Alone Test

    10. STAND ALONE TEST 10. STAND ALONE TEST 10.1 Introduction This manual explains how to examine the status of RX and TX of the model. A. Tx Test TX test - this is to see if the transmitter of the phones is activating normally. B.

  • Page 120: Means Of Test

    10. STAND ALONE TEST 10.3 Means of Test a. Select a COM port b. Set the values in Tx or Rx c. Select band and channel d. After setting them all above, press connect button. e. Press the start button Figure 10-1.
  • Page 121 10. STAND ALONE TEST Figure 10-2. HW test setting Figure 10-3. Ramping profile - 122 -...

  • Page 122: Auto Calibration

    11. AUTO CALIBRATION 11. AUTO CALIBRATION 11.1 Calibration A. Overview Auto-cal (Auto Calibration) is the PC side Calibration tool that perform Tx, Rx and Battery Calibration with Agilent 8960(GSM call setting instrument) and Tektronix PS2521G(Programmable Power supply). Auto-cal generates calibration data by communicating with phone and measuring equipment then write it into calibration data block of flash memory in GSM phone.
  • Page 123 11. AUTO CALIBRATION JTAG2 JTAG1 Status ADI-REMOTE TI-REMOTE POWER VBAT UART Status POWER Figure 11-3 The top view of Test JIG D. Test Jig Operation Power Source Description Power Supply Usually 4.0V Travel Adaptor Use TA, name is TA-20G(24pin) Table 11-2 Jig Power Switch Number Name Description...
  • Page 124 1. Connect as Fig 11-2 (RS232 serial cable is connected between COM port of PC and MON port of TEST JIG, in general.) 2. Run Hot_Kimchi.exe to start calibration. 3. From the Calibration Lib menu, Select F3000, then, Press APPLY! KG320 - 125 -...
  • Page 125 11. AUTO CALIBRATION 4. Press Calibration START KG230 KG320 This model is KG320) Test band : GSM900/DCS 1800/PCS 1900 Max target : dfasdf 5. Select RF Cable Loss value from the Offset menu 6. Press START to execute calibration KG220...

  • Page 126: Agc

    11. AUTO CALIBRATION 11.2 AGC This procedure is for Rx calibration. In this procedure, We can get RSSI correction value. Set band EGSM and press Start button the result window will show correction values per every power level and gain code and the same measure is performed per every frequency.
  • Page 127 - 128 -...

  • Page 128: Exploded View & Replacement Part List

    12. EXPLODED VIEW & REPLACEMENT PART LIST 12.1 EXPLODED VIEW - 129 -...
  • Page 129 - 130 -...

  • Page 130: Replacement Parts

    MTAB03 TAPE,PROTECTION MTAB0121801 TAPE,PROTECTON WINDOW_INNER MTAD00 TAPE,WINDOW MTAD0049801 KG320 TAPE,WINDOW MWAC00 WINDOW,LCD MWAC0065201 KG320 WINDOW,LCD ACGM00 COVER ASSY,REAR ACGM0069001 KG320 COVER ASSY,REAR Black AHFB00 HINGE ASSY,SLIDE AHFB0000701 Black MHFZ00 HINGE MHFZ0009001 KG320 HINGE,SLIDE MMAZ00 MAGNET MMAZ0003501 KG320 MAGNET MPFF00 PLATE,LOGO...
  • Page 131 Black MPBJ00 PAD,MOTOR MPBJ0030401 KG320 PAD,MOTOR MPBN00 PAD,SPEAKER MPBN0027801 KG320 FELT,SPEAKER MPBT00 PAD,CAMERA MPBT0025801 KG320 PAD,CAMERA MPBZ00 MPBZ0117701 KG320 PAD BACK-UP BATT MPFD00 PLATE,GROUND MPFD0002901 kg320 plate,ground MSDB00 SPRING,COIL MSDB0001701 G7000 Pearl White MTAA00 TAPE,DECO MTAA0108501 KG320 TAPE,CAMERA DECO MTAB00...
  • Page 132 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark MIDZ00 INSULATOR MIDZ0094701 KG320 INSULATOR(SUB PCB) - 133 -...

  • Page 133: Main Component

    SBOM standard on GCSC Location Level Description Part Number Specification Color Remark PCB ASSY,FLEXIBLE,SMT SACC00 SACC0021701 KG320 EUA_KEY PAD Black BOTTOM C101 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C102 CAP,CERAMIC,CHIP ECCH0000120 39 pF,50V,J,NP0,TC,1005,R/TP C103...
  • Page 134 VARISTOR SEVY0001001 14 V, ,SMD ,50pF, 1005 VA101 VARISTOR SEVY0001001 14 V, ,SMD ,50pF, 1005 PCB ASSY,FLEXIBLE,SMT SACD00 SACD0031001 KG320 EUA _KEY PAD Black CONNECTOR, CN100 ENBY0020101 20 PIN,0.4 mm,ETC , ,H=1.5, Header BOARD TO BOARD SPCY00 PCB,FLEXIBLE SPCY0069801 POLYI ,0.5 mm,MULTI-4 ,...
  • Page 135 Specification Color Remark MLAC00 LABEL,BARCODE MLAC0003301 EZ LOOKS(use for PCB ASSY MAIN(hardware)) PCB ASSY,MAIN,SMT SAFC00 SAFC0069901 KG320 EUA_MAIN PCB Black BOTTOM ANT201 ANTENNA,GSM,FIXED SNGF0016701 3.0:1 ,0 dBd, ,8x2x1.2 B.T PIFA SMD Pb-Free C100 CAP,CERAMIC,CHIP ECCH0002002 47000 pF,10V ,K ,B ,HD ,1005 ,R/TP...
  • Page 136 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C135 CAP,CERAMIC,CHIP ECCH0000120 39 pF,50V,J,NP0,TC,1005,R/TP C136 CAP,CERAMIC,CHIP ECCH0000120 39 pF,50V,J,NP0,TC,1005,R/TP C137 CAP,CERAMIC,CHIP ECCH0000120 39 pF,50V,J,NP0,TC,1005,R/TP C138 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C139 CAP,CERAMIC,CHIP ECCH0000122...
  • Page 137 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C307 CAP,TANTAL,CHIP,MAKER ECTZ0004205 33 uF,6.3V ,M ,STD ,2012 ,R/TP C308 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C309 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C310 CAP,TANTAL,CHIP,MAKER ECTZ0004205...
  • Page 138 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C422 CAP,CHIP,MAKER ECZH0000826 27 pF,50V ,J ,NP0 ,TC ,1005 ,R/TP C423 CAP,CERAMIC,CHIP ECCH0000120 39 pF,50V,J,NP0,TC,1005,R/TP C424 CAP,CHIP,MAKER ECZH0000803 2 pF,50V ,C ,NP0 ,TC ,1005 ,R/TP C425 CAP,CERAMIC,CHIP ECCH0000178...
  • Page 139 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark FL201 FILTER,CERAMIC SFCY0000901 2450 MHz,2.00*1.25*0.95 ,SMD ,Bluetooth Band Pass Filter FL301 FILTER,EMI/POWER SFEY0007401 SMD ,Coated type , CSP Package , 4-Channel ESD SMD ,SMD ,18 V,4ch. EMI_ESD Filter (100Ohm,15pF), Pb- FL303 FILTER,EMI/POWER SFEY0010501...
  • Page 140 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R196 RES,CHIP ERHY0000201 0 ohm,1/16W,J,1005,R/TP R197 RES,CHIP ERHY0000261 10K ohm,1/16W,J,1005,R/TP R202 RES,CHIP ERHY0000254 4.7K ohm,1/16W,J,1005,R/TP R203 RES,CHIP ERHY0000273 47K ohm,1/16W,J,1005,R/TP R204 RES,CHIP ERHY0000280 100K ohm,1/16W,J,1005,R/TP R207 RES,CHIP ERHY0000261...
  • Page 141 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark R410 RES,CHIP ERHY0000201 0 ohm,1/16W,J,1005,R/TP R412 RES,CHIP ERHY0000220 100 ohm,1/16W,J,1005,R/TP R413 RES,CHIP,MAKER ERHZ0000205 1 Mohm,1/16W ,F ,1005 ,R/TP R414 RES,CHIP ERHY0000220 100 ohm,1/16W,J,1005,R/TP R415 RES,CHIP ERHY0000263 15K ohm,1/16W,J,1005,R/TP R416...
  • Page 142 .032768 MHz,20 PPM,7 pF,65000 ohm,SMD ,6.9*1.4*1.3 X400 VCTCXO EXSK0006601 26 MHz,2.5 PPM,10 pF,SMD ,3.2*2.5*1.2 ,Pb Free SPFY00 PCB,MAIN SPFY0122501 FR-4 ,0.8 mm,BUILD-UP 8 , KG320P64-07-V10c-XXX-XX MAY 08 2006 mot@ KG320 WSYY00 SOFTWARE WSYY0372801 CIS S/W SAJY00 PCB ASSY,SUB SAJY0017202 Black...
  • Page 143 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C120 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C121 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C122 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP C123 CAP,CERAMIC,CHIP ECCH0004904...
  • Page 144 12. EXPLODED VIEW & REPLACEMENT PART LIST Location Level Description Part Number Specification Color Remark C229 CAP,CERAMIC,CHIP ECCH0000182 0.1 uF,10V ,K ,X5R ,HD ,1005 ,R/TP C233 CAP,CERAMIC,CHIP ECCH0000143 1 nF,50V,K,X7R,HD,1005,R/TP CONNECTOR, CN102 ENBY0025701 34 PIN,0.4 mm,ETC , ,H=1.5, Socket BOARD TO BOARD CN201 CONNECTOR,ETC ENZY0016601...
  • Page 145 EUSY0154410 Regulator WLCSP ,67 PIN,R/TP ,WLCSP ,67PIN,R/TP U202 EUSY0259801 ,MA5Si2(64POLY MIDI / Internal D-AMP) SAJD00 PCB ASSY,SUB,SMT TOP SAJD0011601 KG320 EUA_SUB PCB Black C115 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP C116 CAP,CERAMIC,CHIP ECCH0004904 1 uF,6.3V ,K ,X5R ,TC ,1005 ,R/TP...

  • Page 146: Accessory

    SBOM standard on GCSC Location Level Description Part Number Specification Color Remark ADEY00 DATA KIT ADEY0001057 KG320 Data kit of English version MBAZ04 MBAZ0004701 CD Cover MCHZ00 COMPACT DISK MCHZ0016101 Black MMBA00 MANUAL,INSTALLATION MMBA0018505 Installation guide for PC Sync...
  • Page 147 Note...
  • Page 148 Note...

Table of Contents