Cooper Lighting MS600 Instruction Manual

MS600 (Black)
MS600W (White)
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Flathead screwdriver
• Outdoor weatherproof silicone caulking
• (2) 150 watt (MAX) PAR 38 floodlight bulbs
NOTE: This fixture was designed to work with up to 150 watt maximum PAR halogen flood
bulbs. For improved energy efficiency, lower wattage PAR halogen flood bulbs may be used.
Compact Fluorescent (CFL) bulbs contain electronics which may interfere with the motion
sensing function of your fixture and are not recommended.
HOW IT WORKS
Your motion activated floodlight senses heat images
from objects such as people, large animals and
automobile engines. When motion is detected, the
lights will automatically turn on. Once motion has
stopped, the lights will turn off after a preselected
time delay. Your motion activated floodlight may
also be used as a standard floodlight.
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• For outdoor use only.
• cULus LISTED for wet location.
• Suitable for wall mount only. NOT suitable for eave or ground mount installation.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
WARNING
• Read and follow these instructions.
• To reduce the risk of a burn during relamping, disconnect power supply to the unit
before relamping.
• Bulb gets HOT quickly!
• The bulb and fixture get extremely hot during use. Disconnect power and allow fixture
to cool before changing bulb or handling fixture.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
Questions? / ¿Preguntas ? 1-800-334-6871 ConsumerProducts@cooperlighting.com
PACKAGING CONTENTS / CONTENIDO DEL PAQUETE
A. Light fixture and
motion detector
Accesorio y detector
de movimiento
110 degrees
B. Coverplate gasket C. Mounting bracket
Junta de la placa
de cubierta
E. (2) Wire nuts F. (2) Fixture mounting screws
(2) Conectores de cable
• Always replace bulb with the same wattage or lower wattage than included. Installing
a bulb of a higher wattage could create a fire hazard. Use of a higher wattage bulb will
void the warranty. (Maximum 150 watt halogen bulb.)
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source.
Any other connection voids the warranty.
• Fixture must be mounted to a grounded recessed
junction box marked for use in wet locations.
• Suitable for wall mount only. NOT suitable for
eave or ground mount installation.
• Fixture must be mounted horizontally, not
vertically (Fig. 1).
• Keep away from flammable objects. Do not position fixture within
2 inches of any combustible materials.
Up to 70 feet
• Do not position lamp housing within 2 inches of house.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatus (including amplifiers) that produce heat.
• Only use attachments/accessories specified by the manufacturer.
• MINIMUM 90° C SUPPLY CONDUCTORS.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation. Under Part 15 of the FCC Rules, any changes or
modifications to the motion detector described in this instruction sheet that are
not expressly approved by Cooper Lighting, LLC could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
1
Instruction Manual/ Instrucciones
D. (2) #6 and (2) #8 mounting screws
(use the size that fits your junction box)
Soporte para montaje
(2) Tornillos #6 y (2) tornillos #8 de
montaje (utilice el tamaño que mejor
se adecue a su caja de conexión)
G. (2) Lampholder gaskets
(2) Tornillos de montaje (2) Juntas obturadoras
del receptáculo
del accesorio
Fig. 1
Correct Incorrect