Page 1
∗ Refer to the PARTS LIST DC cord DC cord Plastic cabinet assy Mounting hardware assy (E30-4940-05) (E30-4944-05) (A02-1486-13) (J21-9716-03) Lever Remote controller assy Screw set Screw set Escutcheon (D10-4589-04) RC-410 (A70-2025-05) (N99-1719-05) (N99-1656-05) (B07-3055-05) : KRC-765 only : KRC-765 only...
KRC-765/691/691Y COMPONENT DESCRIPTION SYNTHESIZER UNIT (X14-68XX-XX) Component Purpose • Function Operation • Conditions • Compatibility SYSTEM µ-COM E-VOL, N.C. NPX Mute logic circuit 4 input NOR gate x 4 Power IC RDS Decoder Reset IC "L" detection voltage: 3.0 V or less...
KRC-765/691/691Y MICROCOMPUTER'S TERMINAL DESCRIPTION IC1(SYNTHESIZE UNIT : X14-68XX-XX) Pin No. Pin Name Description Processing Operation TYPE 1 Destination type selection port TYPE 2 Destination type selection port F/E IFC OUT input terminal H: Station exists Vth: 2.5V AVSS A/D,D/A converter ground connection terminal Connected to GND lines.
Page 5
KRC-765/691/691Y MICROCOMPUTER'S TERMINAL DESCRIPTION Pin No. Pin Name Description Processing Operation P-CON Power control output H: Power ON L: Power OFF CH-RECH Request output to changers L: Request CH-RST Reset output to changers L: Normally CH-MUTE Mute request from changers...
KRC-765/691/691Y TEST MODE 1. How to enter the test mode • Track jump takes place to the following track when the Track up key is pressed. • Reset the unit while holding preset 1 key and preset 3 No. 9 → No. 15 → No. 10 → No. 11 → No. 12 → No. 13 key.
Page 7
KRC-765/691/691Y TEST MODE 10. Special display when the display is All ON 2. Enter the security registration mode by pressing the CLK key. If the PRESET key is pressed while all displays are turned 3. Enter the CODE by pressing the Track up/down and AM/ on by ALL OFF, the following display appears.
KRC-765/691/691Y ADJUSTMENT BALANCE/FADER/BASS/MID/TREBLE : CENTER T.ADV/METAL/DOLBY NR : OFF INPUT OUTPUT ALIGNMENT ITEM ALIGN FOR FIG. SETTINGS SETTINGS POINTS Adjust so that output Head azimuth TCC-153 level in playing FWD AZIMUTH SP OUT screw 10kHz and REV becomes (FWD/REV) maximum each.
PC BOARD (Component Side View) PC BOARD (Foil Side View) SWITCH UNIT DAUGHTER UNIT DAUGHTER UNIT SWITCH UNIT SWITCH UNIT SWITCH UNIT X16-1640-10/1662-70 (J74-1314-02) X89-2510-10/2522-70 (J74-1325-02) X89-2510-10/2522-70 (J74-1325-02) X16-1640-10/1662-70 (J74-1314-02) (X16-1640-10/1662-70) (X16-1640-10/1662-70) REMO L-CLK L-CE L-INH Refer to the schematic diagram for the values of resistors and capacitors.
PC BOARD (Component Side View) SYNTHESIZER UNIT PRE OUT FRONT REAR SYNTHESIZER UNIT X14-6830-20/6832-71/6842-70 (J74-1324-02/1386-02) (X14-6830-20/6832-71/6842-70) L1/J1 R141 R246 R107 R111 DATA IC11 S-MTR C143 R165 C148 C141 R241 R256 R164 C147 R240 C144 C145 R163 R239 TEST 12MHz R237 R236 R235 R228...
Page 11
PC BOARD (Foil Side View) SYNTHESIZER UNIT PRE OUT REAR FRONT X14-6830-20/6832-71/6842-70 SYNTHESIZER UNIT (J74-1324-02/1386-02) (X14-6830-20/6832-71/6842-70) L1/J1 R248 C143 R245 R263 R243 R253 R262 R238 R209 R166 R210 R168 R247 R167 R222 R169 R226 C165 C166 R171 C154 4.332MHz C121 R217 C122 R137...
Page 12
C131 R62 470 D/A DATA/NC +10.5V 0.01 L-DATAS R63 470 L-INH/L-RST D/A CLK/NC 5 REMO FLIP DET 4 EJECT 3 D/A CLK/NC KRC-765/691/691Y (1/2) EJECT ILL FLIP DET (X14-68XX-XX) ESD-G 1 UNIT MODEL NAME R201 R202 KRC-765 30-20 X86-3240-11 100K...
ELECTRO 220UF 10WV ∗ H54-2297-03 ITEM CARTON CASE C61-68 CK73GB1E473K CHIP C 0.047UF K ∗ H54-2300-03 ITEM CARTON CASE C61-68 CK73GB1H473K CHIP C 0.047UF K CK73GB1H103K CHIP C 0.010UF K M: KRC-765 E: KRC-691Y E1: KRC-691 indicates safety critical components.
(H) ....... 53mm Weight ........... 1.20kg (D) ....... 150mm Weight ........... 1.20kg KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice. US and foreign patents licensed from Dolby Laboratories Licensing Corporation.