SUPPLEMENTS PUBLISHED SONY. CIRCUIT COMPOSANTS SONY DONT LE NUMÈRO DE PIÈCE EST ADJUSTMENTS THAT ARE CRITICAL FOR SAFE OPERATION INDIQUÈ DANS LE PRÈSENT MANUEL OU DANS DES ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE SUPPLÈMENTS PUBLIÈS PAR SONY. LES RÉGLAGES DE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE CIRCUIT DONT L’IMPORTANCE EST CRITIQUE POUR LA...
SELF DIAGNOSTIC FUNCTION OUTLINE • The units in this manual contain a self-diagnostic function. • If an error occurs, the STANDBY lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 5
DISPLAY OF STANDBY LIGHT FLASH COUNT * One flash count is not used for self-diagnostic. < Diagnostic Item > < Flash Count > 2 times • +B OCP/OVP PUSH TEMER REC REC • Vertical deflection stopped 4 times • White balance failure 5 times STANDBY lamp (RED) Lamp ON 0.3 sec.
Page 6
SELF-DIAGNOSTIC CIRCUIT LED flash IC001 µ-COM STANDBY lamp To item 2 and 5 via bus line SCL1 D1304 SDA1 RY603 RELAY MEMORY IC002 ITEM 2 Over current VCR PWR Q601 Detection(OVP) Q606 V PULSE STOP R611 • R656 Q611 +B LINE Q612 IC301 Y/C/J...
SECTION 3 SET-UP ADJUSTMENTS Perform the adjustments in the following order: • The following adjustments should be made when a complete realignment is required or a new picture tube is installed. 1. Beam Landing 2. Convergence • These adjustments should be performed with the rated 3.
• Movement of red, green and blue dots by V. STAT tilting 3-2. CONVERGENCE and opening or closing. Purity 1 Movement of opening or closing the BMC magnet V. STAT convergence magnet. Vertical static convergence magnet Movement of tilting the V. STAT conver- gence magnet counterclockwise.
(2) Convergence adjustment of screen surroundings. 3-3. FOCUS ADJUSTMENT (Dynamic convergence) 1. Receive monoscope pattern. 1. Recieve dot pattern. 2. Adjust FBT focus VR so that the picture has the best focus. 2. Set BRT to main and PIC to the level where dot pattern is Adjust the focus so that the center of the screen is in the best easy to see.
3-5. WHITE BALANCE ADJUSTMENT 1. Input ehite pattern. Adjust white balance of drive side, using service mode VP No. 22 RAMP, No. 23 GAMP and No. 24 BAMP, so that colour temperature is 8600 K + 0 MPCD. 2. Input gray pattern for 10NIT. Adjust white balance of cut-off side, using service mode No.
SECTION 4 CIRCUIT ADJUSTMENTS 4-1. ADJUSTMENTS WITH COMMANDER 6. WRITING "STANDARD VALUE" 1. ENTERING SERVICE MODE 1) Set to service mode. 1) Turn on the main power of the set and enter into stand-by 2) When push 5 button on the remote commander green mode.
4-2. ADJUSTMENT METHOD Service adjustment to this model can be performed with the supplied Remote Control Commander RM-955, 956. • HOW TO ENTER INTO SERVICE MODE Entering the service mode When exchange When exchange When repair connect- the MEMORY the board ed with picture quality IC002 (MA10 board) Perform “standard...
4-3. SERVICE DATA DISP DATA STANDARD ITEM DEVICE RANGE DATA VP00 SBRT 00-3F SUB BRIGHT CXA2139S VP01 HSIZ 00-3F H SIZE (Y/C/J) VP02 HPOS 00-3F H POSITION VP03 VSIZ 00-3F V SIZE VP04 LCPN 00-3F LOWERSIDE CORNER PIN VP05 UCPN 00-3F UPPERSIDE CORNER PIN VP06...
DISP DATA STANDARD ITEM DEVICE RANGE DATA IF00 AMFM 00-01 AUTO MUTE FM IF01 GAIN 00-01 AUDIO GAIN IF02 GATE 00-01 GATING (POSITIVE MODULATION) IF03 00-1F TAKE OVER POINT *DISPLAY -16 to +15* CXP85452 (µ-COM) IF04 TAGC 00-1F AGC FOR TV TUNER *DISPLAY -16 to +15* IF05 VAGC 00-1F...
SECTION 2 DISASSEMBLY 2-1. TOP COVER REMOVAL 2-2. VCR BLOCK ASSY REMOVAL 1 Four screws 4 screw (+BVTP 3 X 6) (+BVTP 3 X 12) 3 Five screws (+BVTP 3 X 12) RP earth plate 2 Top cover 5 VCR BLOCK assembly 1 CN701 2 Two screws (+BVTP 3 X 12)
Page 44
SECTION 3 CIRCUIT ADJUSTMENTS [ SET-UP FOR ADJUSTMENT ] Necessary items and indications for total adjustment of electric The video signal from the pattern generator is used as adjustment circuit of this unit will be described in this chapter. signal for electrical adjustment. This video signal should meet the requirement.
Page 45
X’tal OSC CHECK CARRIER DEVIATION CHECK Mode Mode Signal Alignment tape, Stair step Signal Color bar MA10 board IC802 %ªpin(PAL) MA10 board IC802 !•pin Measurement Point Measurement Point Measurement Equipment Oscilloscope Measurement Equipment Spectrum Analyzer Specified Value 500±200mVp-p Specified Value =1.00±0.08MHz Check: 1)Confirm the frequency is 4.433619MHz±100Hz(PAL).
Page 46
REC Y LEVEL CHECK PB Y LEVEL CHECK Mode E-E(SP) Mode Signal No signal Signal Color bar MA10 board IC802 !•pin Measurement Point Measurement Point MA10 board Q830 emitter Measurement Equipment Oscilloscope Measurement Equipment Oscilloscope Specified Value 260±70mVp-p(PAL) Specified Value 1.0±0.1Vp-p Check: Confirm the Vp-p of the waneform is 1.0±0.1Vp-p.
Page 47
SECTION 4 INTERFACE, IC PIN FUNCTION DESCRIPTION 4-1. µ-COM PORT FUNCTION DESCRIPTION (MA10 BOARD IC001) Pin No. Signal Function S SEL F S-INPUT SELECT (FRONT) S SEL R S-INPUT SELECT (REAR) TU STEREO MODE TU BILINGUAL MODE DGC SW – DGC ON/OFF CONTROL ST/ MONO SET MODE STEREO/MONO...
CN1001 :S-MICRO GND(AV) FE HEAD FULL ERASE HEAD CN1002 CTL(X) HEAD CTL(Y) GND(AV) AUDIO(P MA10(2/3) BOARD MARK LIST AUDIO A HEAD PB REC/PB A HEAD REC HEAD Ref No. FR model AEP/UK/ESP model GND(AV) AUDIO AERASE HEAD C1801 0.01 B:CHIP —...
Page 61
VOLTAGE D(AV) no mark:REC/PB ):REC < >:PB HEAD SW5V TL(X) TL(Y) D(AV) AUDIO(PB) SW5V D PB R1020 AUDIO(REC) 1/10W :CHIP D(AV) Q1001 2SD879-AA C1016 HEAD 47 16V C1014 R1017 (1.1)<4.8> (4.4) 0.01 5.6k R1023 1/4W <4.8> 5.6k C1002 F:CHIP R1003 :FPRD 1/10W 0.01...
The components identified by shading SECTION 6 and mark are critical for safety. Replace only with part number specified. EXPLODED VIEWS NOTE: • The construction parts of an assembled part are Les composants identifiés par la marque indicated with a collation number in the remark sont critiques pour la sécurité.
Page 66
6-2. CHASSIS Les composants identifiés par la marque The components identified by shading sont critiques pour la sécurité. and mark are critical for safety. : 7-685-648-79 +BVTP 3X12 Ne les remplacer que par une pièce Replace only with part number specified. : 7-682-147-01 +P 3X6 portant le numéro spécifié.
Page 67
6-3. MECHANISM DECK ASSEMBLY (1) : 7-685-646-79 +BVTP 3X8 Not supplied REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- 3-977-509-01 WASHER, THRUST 3-977-447-01 GEAR, ELEVATOR 3-977-507-01 TABLE, REEL (S) 3-977-514-01 OPENER, LID 3-977-508-01 TABLE, REEL (T) 3-977-441-03 GEAR, PINCH PRESSING...
Page 71
Les composants identifiés par la marque The components identified by shading and mark are critical for safety. sont critiques pour la sécurité. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF. NO. PART NO.
Page 72
Les composants identifiés par la marque The components identified by shading and mark are critical for safety. sont critiques pour la sécurité. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF. NO. PART NO.
Page 73
Les composants identifiés par la marque The components identified by shading and mark are critical for safety. sont critiques pour la sécurité. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF. NO. PART NO.
Page 74
The components identified by shading Les composants identifiés par la marque sont critiques pour la sécurité. and mark are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF. NO. PART NO.
Page 75
Les composants identifiés par la marque The components identified by shading and mark are critical for safety. sont critiques pour la sécurité. Ne les remplacer que par une pièce Replace only with part number specified. A CVM portant le numéro spécifié. REF.
Page 76
The components identified by shading Les composants identifiés par la marque sont critiques pour la sécurité. and mark are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF. NO. PART NO.
Page 77
The components identified by shading Les composants identifiés par la marque sont critiques pour la sécurité. and mark are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié. REF. NO. PART NO.
Page 78
The components identified by shading Les composants identifiés par la marque sont critiques pour la sécurité. and mark are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. MA10 VIDEO BLOCK portant le numéro spécifié. REF.
Page 79
Les composants identifiés par la marque The components identified by shading and mark are critical for safety. sont critiques pour la sécurité. Ne les remplacer que par une pièce Replace only with part number specified. MA10 portant le numéro spécifié. REF.
Page 80
Les composants identifiés par la marque The components identified by shading and mark are critical for safety. sont critiques pour la sécurité. Ne les remplacer que par une pièce Replace only with part number specified. MA10 portant le numéro spécifié. REF.
Page 81
Les composants identifiés par la marque The components identified by shading and mark are critical for safety. sont critiques pour la sécurité. Ne les remplacer que par une pièce Replace only with part number specified. MA10 portant le numéro spécifié. REF.
Page 82
The components identified by shading Les composants identifiés par la marque sont critiques pour la sécurité. and mark are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. MA10 portant le numéro spécifié. REF.
Page 83
Les composants identifiés par la marque The components identified by shading and mark are critical for safety. sont critiques pour la sécurité. Ne les remplacer que par une pièce Replace only with part number specified. MA10 portant le numéro spécifié. REF.