Connecting The Piping; Connecting Pipe To The Indoor Unit; Connecting The Interconnecting Pipe To The Outdoor Unit Valve - Carrier P1 Plus series Owners And Installation Manual

CONNECTING THE PIPING

Pay careful attention to the following points when installing the refrigerant pipes.
• Hold the pipe with one wrench while tightening the connections with a torque
wrench or double-ended wrench.
Be careful not to damage the flare nut threads.
• If the tightening torque is insufficient, gas will leak from the connection.
• If it is too strong, the flare will be damaged.
Tighten the nut with the torque shown in Table 1.
Flare nut
6.35mm (1/4")
9.52mm (3/8")
12.7mm (1/2")
• Do not bend the pipe more than three times at one place.
• When extending the rolled pipe, straighten the pipe by unwinding as shown
in Figure 14.
Page 29
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5

1) Connecting Pipe to the Indoor Unit

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5
a. Remove the indoor pipe flare nut. ( Check that there is no debris inside. )
b. Align the center of the flare surface, and tighten the indoor pipe union and
connection pipe flare nut with a torque wrench or double-ended wrench.
( Figure. 15 )
While aligning the center of the flare surface, tighten the nut by hand, hold the
union side with a wrench and tighten the nut according to the specified
Table 1
tightening torque with a torque wrench.
Tightening torque(kgf-cm)
150 ~ 200
310 ~ 350
500 ~ 550
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5

2) Connecting the Interconnecting Pipe to the Outdoor Unit Valve

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5
• Repeat the procedure for flaring the tube to connect to the outdoor unit.
• Tighten the flare nut of the connection pipe at the outdoor unit valve. ( Figure. 16 )
Figure 14
Three way valve
Torque wrench or
double-ended wrench
Outdoor side
Indoor side
Interconnecting
pipework
(Gas pipe)
(Liquid pipe)
Two way valve
2004.6.11, 3:15 PM
Figure 15
Figure 16
29