HP VS17E SERVICE MANUAL 17” LCD Monitor VS17E THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR...
HP VS17E 2.LCD Monitor Description The LCD Monitor will contain main board, power board, key board and an audio board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.
HP VS17E 3.3 Adjust the Picture Control Icons Control Icons Brightness Clock Phase Contrast Power Saver Auto Adjustment Mode Display Image Control Power-On Status Display Color Sleep Timer Custom Color Basic Menu Language Advanced Menu Management Power On Recall OSD Control...
HP VS17E 4. Input/Output Specification 4.1 Input Signal Connector Mnemonic Signal Mnemonic Signal Red Video +5 V +5 V (from PC) Green Video Sync Ground Blue Video None PC Connect detection DDC Data Ground (DDC Return) Horizontal Sync Red GND...
Page 14
HP VS17E REMARK: 1) MCU initialize. 2) Is the EEprom blank? 3) Program the EEprom by default values. 4) Get the PWM value of brightness from EEprom. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.
HP VS17E 6.3.2 Inverter / Power Board Block Diagram AC input Bridge Rectifier EMI filter Transformer Dc to Dc Rectifier diodes and Filter StartCircuit: CN902 R909/R910/R931 Feedback Over Circuit Voltage Control IC Protect ON/OFF Transformer MOSFET Resonance Lamp Over ON/OFF...
HP VS17E 9. Maintainability 9.1Equipments and Tools Requirement 1. Multi-meter. 2. Oscilloscope. 3. Pattern Generator. 4. DDC Tool with an IBM Compatible Computer. 5. Alignment Tool. 6. LCD Color Analyzer. 7. Service Manual. 8. User Manual.
HP VS17E 9.2 Trouble Shooting 9.2.1 Main Board 1、No power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the power section Measure CN201 PIN5/6=12V?
Page 30
HP VS17E No picture (LED is orange) No picture Y601 oscillate waveforms are Key is under control? normal Replace Y601 X401 oscillate waveforms are normal Replace U601 Replace X401 Replace U401 Check if the sync signal from computer is output and video cable...
Page 31
HP VS17E Panel Power Circuit Measure Q204 base is high level? Y601 oscillate waveforms are normal Check Q204 and Q203 are broken Replace Y601 or CN503 solder? Replace U601 Check Correspondent component. Replace U401 Replace PANEL...
HP VS17E 9.2.2 Power Board No Power No power Check AC line volt 110V or 220V Check AC line Check the voltage of C904(+) Check F901, bridge rectified circuit Check start voltage for the pin3 of IC901 Check R912, R916, R918, IC901...
Page 33
HP VS17E No Backlight Check CN903 Pin1/3 =12V Check adapter Check ON/OFF signal Check Interface board Check IC701 PIN6=5V+0.25V Check Q713,Q712, Q702, ZD701 circuit Check IC701 PIN1=5V Check Q707, Q706 circuit Check IC701 PIN 2 triangular wave is normal Check C720, C719, IC201 circuit...
HP VS17E 9.2.3 Keypad Board OSD is unstable or not working Is Keypad board connecting normally Connect Keypad Board Is Button Switch normally Replace Button Switch Replace Keypad Board Is Keypad board normally Check main board...
C. 6500K color: Don’t adjustment,Custom requires. 3. Into factory mode of HP VS17E A. Turn on power, press the down(-) button, pull out the power cord, and then plug the power cord. Then the factory OSD will be at the left top of the panel.
Page 36
HP VS17E B. Adjust sRGB color-temperature 1. Switch the chroma-7120 to sRGB channel. 2. The chroma 7120 will show x = 313 ±20, y = 329 ±20, Y >200 cd/m 3. Switch the chroma 7120 l to RGB MODE ( with press “MODE” button to change ) 4.
(Center). The exact brightness values are confirmed by the checking-regulations of different customers and different models. Ⅱ. Steps of white-balance adjustment for LCD:(Take 17” HP LCD for example) 1. Required instruments: Chroma7120、Chroma2325(BGA265A) 。 2. First connect the instruments together and turn on the LCD power, then warm up for 30 minutes under full white screen mode.
Page 38
HP VS17E d) Test white-balance again after Auto Level. Adjustment with hand is necessary if it is beyond the specs just the same. e) Select 7x00 item to adjust cool color-temperature and select 6x00 to adjust warm color- temperature. It can reach to the best effect through adjusting R/G/B value if it inclines to green or blue.
Page 39
HP VS17E 3.Input the serial number of the product (For instance: AOC LM729 is 13 bits), then press ENTER to start writing 4.Check the indication of DDC-writing program at the end. When you see the picture as the schematic picture above, “Data compare...
Page 40
HP VS17E Instruction:DDC-writing needs 4 files: Barcode.txt (Supply Barcode length and flow number) *.EXE (DDC-writing program) WR.bat (Group order file for cycling utilization of *EXE, and dual-click this file when perform DDC-writing) 4、w.dat The content with 128 bits of DDC...
HP VS17E 13. BOM List T786KS4DFHHPAPE Location Part No. for TPV Description Quantity Unit CBPC780KS4HPAP CONVERSION BO ARD KEPC782KD4P KEY BOARD PWPC1742SEH3P POWER BOARD FOR ROHS E095 S95G801830578 LVDS ASS'Y 15G8116 4 MAIN FRAME 23G3178690 6A LOGO 33G4788 PC L...
Page 45
HP VS17E R310 61L0603102 RST SM 0603 RC0603 1K P R311 61L0603102 RST SM 0603 RC0603 1K P R408 61L0603102 RST SM 0603 RC0603 1K P R725 61L0603102 RST SM 0603 RC0603 1K P R726 61L0603102 RST SM 0603 RC0603 1K P...
Page 53
HP VS17E JR705 61L1206000 RST SM 1206 JUMP MAX 0R JR706 61L1206000 RST SM 1206 JUMP MAX 0R JR707 61L1206000 RST SM 1206 JUMP MAX 0R JR708 61L1206000 RST SM 1206 JUMP MAX 0R JR709 61L1206000 RST SM 1206 JUMP MAX 0R...