Troubleshooting - Silvercrest KH 6510 Operating Instructions Manual

KH6510_11_A4_V3_EN.qxd 24.08.2006

14. Troubleshooting

The display is blank/DVD player does not function, even
though it was switched on
A
Check whether the power cord is properly plugged into
the socket.
B
Check whether the socket into which you have plugged
the power cord of the DVD player is supplying electricity
by plugging in another device. Where appropiate plug
the DVD players power cable into another power socket.
C
Check to see that the display dimmer function is switched
off. For this purpose press the button
remote control.
D
Switch the DVD player off by pressing the ON/OFF button
and then wait ten seconds. Switch the DVD player on again
by pressing the ON/OFF button once more.
The display indicates "No Disc", even though a disc was inserted
A
The disc is dirty, scratched or damaged. Clean the disc or insert a
different disc.
B
The Country/Regional code of the inserted DVD/VCD/
S-VCD does not coincide with the Country/Regional code
of the DVD player. In this case, the DVD/VCD/S-VCD cannot
be played with the DVD player.
Inserted disc is not played
A film of condensation may have formed on the laser sensor
lens of the DVD player. In particular, this may occur if the
DVD player has been subjected to extreem temperature fluc-
tuations.
In this case, place the DVD player in a dry environment at
normal room temperature. First remove any inserted disc
from the disc tray. Then leave the DVD player switched off for
at least one hour without using it until the condensation film
has evaporated.
No image or only black and white image
A
Check to see that all connection cables between the DVD
player and television (or Video projector) are plugged
firmly into the corresponding sockets
B
Check whether the settings in the OSD menu match the
connection option you have used to connect the DVD
player to the television (or the video projector).
Ô
For this refer to chapter 6 "Connection of the DVD player
to a television".
12:25 Uhr Seite 23
"Dimmer" on the
- 23 -
C
Using the television's (or Video projector's) instruction
manual check to see if current settings to the television
(or Video projector) are necessary in order to use the
DVD player with the television.
No sound
A
Check to see if the television and/or DVD player are
currently switched to mute.
B
Check to see if all connections cables between the DVD
player and currently connected audio components are
firmly plugged into the corresponding sockets.
C
Check whether the settings in the OSD menu match the
connection option you have used to connect the audio
components to the DVD player.
Ô
For this refer to chapter 7 "Connecting Audio components
to the DVD player.
D
Using the television's instruction manual check to see if
current settings to the television are necessary in order
to use the DVD player with the television.
E
Using the instructions manual of a currently connected
audio component check to see if settings to the compo-
nent are necessary in order to use it with the DVD player.
F
If you ...
Ú
have connected the DVD player to a stereo television and
have not connected an audio component to the DVD player
or
Ú
have connected a Dolby Prologic compatible audio compo-
nent via the analogue stereo outlet (via cinch cables to the
cinch sockets L and R) of the DVD player:
Check to see if you have selected the option Large in the
OSD Menu under the Sub menu option Front LS.
No 4:3 or 16:9 image
A
Consult the operating manual of the television to determine
which image format the television supports.
B
Check whether the settings in the OSD menu match the
available image format of the television.
Remote control does not function
A
Check to see that the remote control batteries are inser-
ted into the battery compartment according to the correct
polarity.
B
Check whether the batteries in the remote control are
dead and replace both batteries, if necessary.
KH 6510/6511