Adjust Volume; Adjust Tone; Setting The Time - E-Bench KH 2300 Operating And Safety Instructions Manual

DEVICE/ SOURCE SELECT
• Press the appropriate button
CD = CD player TUNER = radio

ADJUST VOLUME

• To increase the volume use the
• To reduce the volume use the
• To mute (silence) the loudspeakers and headphones press the mute button

ADJUST TONE

[ » CLASSIC / ROCK / POP « ]
Use the tone selector button
current setting CLASSIC, ROCK or POP is shown in the display
HEADPHONES
[ » PHONES « ]
8-32 Ohm stereo headphones
are connected the loudspeakers are turned off. Please note that high levels of sound can lead to serious hearing damage.

SETTING THE TIME

01) For you to be able to set the time, the equipment must be in Stand-by mode (operating display
02) Press MEMORY/CLK-ADJ button
03) Move the hours setting forward or backward using the
04) Press MEMORY/CLK-ADJ button
05) Move the minutes setting forward or backward using the
06) Press the MEMORY/CLK-ADJ button
SETTING TIMES FOR SWITCHING ON AND OFF
If the Switch-on time feature is enabled then your Designer Audio Unit can wake you at your chosen time.
01) Using the appropriate button
02) Set up the source, i.e. for TUNER (RADIO) set the desired station, for TAPE (CASSETTE RECORDER) insert the tape and wind
to the correct place or insert a CD and if required program a track sequence.
03) Press TIMER button . The display
0
NOTE: You have five seconds to complete the following steps. Otherwise the process is halted and you must begin
again with step 4.
04) Press the MODE/REMAIN button
05) Press the MEMORY/CLK-ADJ button
06) Move the hours setting forward or backward using the
07) Press MEMORY/CLK-ADJ button
08) Move the minutes setting forward or backward using the
09) Press the MEMORY/CLK-ADJ button
10) If you wish to be woken to a cassette: Press the Play button
11) Then switch off the Designer Audio Unit (ON-/OFF-button
If you enable the Switch-off time feature, your Designer Audio Unit will always switch off at the set time.
01) Press the TIMER button
0
NOTE: You have five seconds to complete the following steps. Otherwise the process is halted and you must
begin again with step 2.
02) Press the MODE/REMAIN button
03) Press the MEMORY/CLK-ADJ button
04) Move the hours setting forward or backward using the
05) Press MEMORY/CLK-ADJ button
06) Move the minutes setting forward or backward using the
07) Press the MEMORY/CLK-ADJ button
To switch off the TIMER functions, press the TIMER button
[ » CD / TUNER / TAPE / AUX « ]
to select a device or change the source:
*
TAPE = cassette recorder
[ » VOLUME / MUTE « ]
button .
W
button .
Q
to set the tone quality of a track to suit the type of music and increase listening pleasure. The
%
can be connected to the headphones connector with a 3.5 mm jack plug. As soon as the headphones
5
once - the hours display flashes.
\
again - the minutes display flashes.
\
again - the display stops flashing and the clock starts (the colon flashes).
\
select the desired device/ source (CD, TAPE or TUNER).
*
now shows TIMER.
@
twice. The time appears in display
9
once - the hours display flashes.
\
again - the minutes display flashes.
\
again - the Switch on time is stored.
\
. The display now shows TIMER.
@
three times. The time appears in the display
9
once - the hours display flashes.
\
again - the minutes display flashes.
\
again - the Switch-off time is stored.
\
AUX = external device, e.g. record deck
.
^
- (blank display = neutral tone).
@
Forward button or Reverse button
)
Forward button or Reverse button
)
[ » TIMER « ]
and TIMER ON flashes.
@
Forward button or Reverse button
)
Forward button or Reverse button
)
.
3
).
E
and TIMER OFF flashes.
@
Forward button or Reverse button
)
Forward button or Reverse button
)
repeatedly until the display
0
12
lights up red).
R
.
8
.
8
.
8
.
8
.
8
.
8
shows TIMER.
@