Manually Searching For A Radio Station; Improving Reception Quality Of Frequency Modulation (Fm) Radio Stations; Programming A Radio Station; Selecting A Preset Radio Station - Bench KH 2233 Instructions For Use Manual

2
The next available radio station will be found automati-
cally. As soon as a radio station is found with a sufficient
broadcast signal, the station search will be stopped.
3
If you would like to search further for a radio station:
Press and hold the Skip/Tun forwards or Skip/Tun re-
verse button again for a few seconds. The station search
will continue until the next radio station with a sufficient
broadcast signal is found.

10.2. Manually searching for a radio station

The manual search can be used to find radio stations, for
which only poor reception quality is available. To do this,
press the Skip/Tun forwards or the Skip/Tun reverse button
repeatedly. You can use this function to ...
Ú
search the medium wave (AM) frequency range in steps
of 9 kHz
Ú
search the frequency modulation (FM) frequency range
in steps of 0.05 MHz.
Repeat this until you have found the required radio station.
If you would like to search for a stereo radio station in the
FM (frequency modulation) frequency range: First press the
FM Mode/ST/Mono button on the main unit. If a stereo ra-
dio station is found, then the stereo symbol will appear on
the display screen.
10.3. Improving reception quality of
frequency modulation (FM) radio stations
To improve reception quality of FM radio stations:
1 Uncoil the trajectory antenna connector cable to its full
length. Slowly move the end of the trajectory antenna
connected to the main unit so that it points in different
directions. Once you have found a good position for re-
ception of the radio station: Fix the trajectory antenna in
this position (e.g. with tape).
2
In the case of poor reception of a frequency modula-
tion (FM) radio station in stereo mode, it could also help
to switch to mono reception. To do this, press the FM
Mode/ST/Mono button once if stereo reception is cur-
rently on. The stereo indicator will disappear from the
display screen.

10.4. Programming a radio station

You can preset up to ten radio stations in each frequency
range. To do this:
1
Use the automatic search function or the manual search
function to search for the radio station that you would
like to preset.
2
Press the Memo/C-Adj button on the main unit. 01 will
appear and Memory will blink on the display screen for
the first of ten program positions.
3
Press the Repeat/M-Up button on the remote control unit
to select another program position. You can switch to the
next program position by pressing the button again.
4 Once the program number, under which you would like
to save the radio station, appears on the display screen:
Press the Memo/C-Adj button again. The radio station is
now preset for the selected program position. Memory
appears on the display screen.
5
To preset additional radio stations on other program po-
sitions: Repeat steps 1 to 4.
To move a preset radio station to another program position:
1
Select the desired radio station.
2
Press the Memo/C-Adj button. Memory blinks on the
display screen.
3
Press the Repeat/M-Up button to select another pro-
gram position.
4
Once the program number, under which you would like
to save the radio station, appears on the display screen:
Press the Memo/C-Adj button again. The radio station is
now preset for the selected program position. Memory
appears on the display screen.
ô
Note:
If you preset a radio station to correspond to a program posi-
tion that is already occupied: Then the radio station that was
previously preset for the program position will be deleted.
In the case of power outages: If the power outage memory of
the mini hi-fi system has been activated, then all of the radio
stations will remain in memory. This is explained in more
detail in chapter 8.3. of these instructions.
If the power outage memory is not activated, then all of the
stored radio stations will be deleted in the case of a power
outage. Settings will also be deleted if the power cable is un-
plugged.

10.5. Selecting a preset radio station

1
Press the Stop/Band button to select the frequency range
of the preset radio station. The selected frequency range
(AM medium wave or FM frequency modulation) will
appear on the display screen.
2
Press the Repeat/M-Up button to switch to the next
stored radio station. The program position of the current-
ly selected radio station appears on the display screen.
English • 11