Black & Decker FSMH1621-XE Manual page 7

Assembly
Warning! Before attempting any of the following operations,
make sure that the appliance is switched off and unplugged
and that the appliance is cold and does not contain any water.
Attaching the handle (Fig. A)
Slide the bottom end of the handle (10) into the top end of
u
the steam mop body (9) until it clicks into place.
Attaching the steam head (Fig. B)
Slide the bottom end of the steam mop body (9) onto the
u
steam head (11) until it clicks into place.
The steam head can be removed from the Steam mop
u
body by pressing the steam head release button (18) and
pulling the steam mop body (9) off the steam head (11).
Attaching the hand held stean cleaner (Fig. C)
Holding the back of the steam mop body (9) Push the
u
hand held steam cleaner (5) firmly into the stem mop body
(9) until it clicks into place.
Caution! Always ensure the handle command lights up to
confirm the unit is docked.
Warning! Inspect that the seal (22 Fig. G) on the steam noz-
zle (4) before fitting the hand held steam mop to the steam
mop body. If the seal is missing or damaged then please
contact your nearest authorised repair agent. Do not use the
appliance.
Removing the hand held stean cleaner (Fig. C)
Push the release button (19) down and pull the hand held
u
steam cleaner (5) away from the steam mop body
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your Black &
Decker dealer:-
Steam head cleaning pad - cat. no. FSMP20-XE).
Place a cleaning pad (12) on the floor with the 'hook &
u
loop' side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(12).
Caution! Always place your steam mop on the resting mat
(13) with the handle (10) in the upright position when station-
ary and make sure the steam mop is turned off when not in
use.
Removing a cleaning pad (Fig. E)
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (10) to the upright position and turn the
u
steam mop 'OFF'.
(Original instructions)
Place the steam mop on the resting mat and wait until it
u
cools down. (approximately five minutes)
Place the front of your shoe onto the cleaning pad removal
u
tab (20) and press down firmly.
Lift the steam mop up off the cleaning pad.
u
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Attaching the carpet glider (Fig. F)
Place carpet glider on the floor.
u
Attach a claening pad to the unit.
u
Lightly press the steam mop down onto the carpet glider
u
(14) until it clicks into place.
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Removing the carpet glider (Fig. F)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (10) to the upright position and turn the
u
steam mop 'OFF'.
Place the steam mop on the resting mat and wait until it
u
cools down. (approximately five minutes)
Place the front of your shoe onto the carpet glider removal
u
tab (21) and press down firmly.
Lift the steam mop up off the carpet glider (14).
u
Caution! Always place the steam mop on the resting mat (13)
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Attaching the hose and accessories to the Hand
held steam cleaner (Fig. G & H)
Warning! Inspect the seal (22) on the steam nozzle (4) and
hose (23) before each use. If the seal is missing or damaged
then please contact your nearest authorised repair agent. Do
not use the appliance.
Attaching the hose (Fig. G)
Press in the clips (24) on either side of the hose (23).
u
Press the hose (23) onto the steam nozzle (4) and release
u
the clips (24).
Important! Ensure that the hose (23) is securely fastened
before using the hand held steeam cleaner. If steam escapes
from the joint then the hose is not correctly fit, allow the unit to
cool then remove and re-fit the hose.
Attaching the variable stem jet nozzle (Fig. H)
Press in the clips (26) on either side of the variable stem
u
jeet nozzle (27).
ENGLISH
7