Page 1
ZAS17 CX–NSZ207 • This Service Manual is the “Revision Publishing” and replace “Simple Manual” NSX-SZ201/203/207<K,V,EZ>, (S/M Code No. 09-012-440-9T2). • If requiring information about the CD mechanism, see Service Manual of BZG-2 (S/M Code No. 09-00C-353-2N2). S/M Code No. 09-013-440-9R2...
NOTE ON BEFORE STARTING REPAIR 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed.
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
Page 5
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
ELECTRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 87-010-384-080 CAP,E 100-25 M 11L SME<203EZ,203V> 87-010-407-080 CAP, E 33-50V<201K,207EZ> 87-A21-269-010 IC,EW732 87-010-384-080 CAP,E 100-25 M 11L SME<203EZ,203V> 87-A21-893-040 C-IC,NJM14558V-TE2 87-010-407-080 CAP, E 33-50V<201K,207EZ> 87-A21-419-040 C-IC,NJM14558MD-TE2 87-010-393-080...
Page 7
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C460 87-010-759-080 C-CAP,U, 0.1-25F C516 87-010-759-080 C-CAP,U, 0.1-25F C461 87-A12-466-080 C-CAP,U 390P-50 J SL C517 87-012-272-080 C-CAP,U 680P-50 B C462 87-A12-466-080 C-CAP,U 390P-50 J SL C518 87-012-272-080 C-CAP,U 680P-50 B C470 87-012-270-080 C-CAP,U 470P-50 K B...
CHIP RESISTOR PART CODE Chip Resistor Part Coding Figure Resistor Code Value of resistor Chip resistor Dimensions (mm) Symbol Wattage Type Tolerance Resistor Code Form 1/16W 1005 0.35 1/16W 1608 0.45 1/10W 2125 1.25 0.45 1/8W 3216 0.55 TRANSISTOR ILLUSTRATION E C B B C E B C E...
Page 28
IC DESCRIPTION IC, UPD780226GF-022-3BA Pin No. Pin Name Description SOL1 DECK1 solenoid output. SOL2 DECK2 solenoid output. O-MOTOR DECK MOTOR ON/OFF output. O-PB2 DECK2/DECK1 play output. O-BIAS BIAS ON output. O-RMT REC mute output. O-CD. ON CD ON output. O-TU. ON TUNER ON output.
Page 29
Pin No. Pin Name Description I-SPEANA2 A/D 2 input for spectrum analyser level display. I-SPEANA3 A/D 3 input for spectrum analyser level display. I-KEY1 Key 1 input. I-KEY2 Key 2 input. I-TU. SIG Tuner tuning signal level input. (Not used) AVSS GND.
Page 30
ADJUSTMENT – 1 <TUNER / FRONT> < TUNER SECTION > 1. Clock Frequency Check 11. Output Level Check Settings : • Test point : TP2 (CLK) <AM(MW)> Method : Set to AM(MW) 1602 kHz and check that the test point Settings : •...
Page 31
ADJUSTMENT – 2 <DECK> < DECK SECTION > 1. Tape Speed Adjustment (DECK 2) 4. REC/PB Frequency Response Check (DECK 2) Settings : • Test tape : TTA–100 Settings : • Test tape : TTA–602 • Test point : TP8 (Lch), TP9 (Rch) •...
CD TEST MODE 1. How to Start the CD Test Mode While pressing the FUNCTION button, insert the AC plug to the power outlet. When the test mode is started, the message [CD TEST] is displayed. 2. How to Exit the CD Test Mode Press the POWER button or disconnect the AC plug.
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) Type.1 Type.4 TOOLS Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units. 2 (() flat head screwdriver 3 Cut chisel How to Remove the PANEL, FR...