Black Box 12-Port 1000BASE-TX L2 Managed PoE Switch User Manual
  1. Manuals
  2. Brands
  3. Black Box Manuals
  4. Switch
  5. 12-Port 1000BASE-TX L2 Managed PoE Switch
  6. User manual
Black Box 12-Port 1000BASE-TX L2 Managed PoE Switch User Manual

Black Box 12-Port 1000BASE-TX L2 Managed PoE Switch User Manual

With 2 sfpdual media ports
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
©
Copyright 2006. Black Box Corporation. All rights reserved.

Advertisement

Table of Contents
loading

Related Manuals for Black Box 12-Port 1000BASE-TX L2 Managed PoE Switch

Summary of Contents for Black Box 12-Port 1000BASE-TX L2 Managed PoE Switch

  • Page 1 © Copyright 2006. Black Box Corporation. All rights reserved.
  • Page 2 (outside U.S. call CUSTOMER toll-free 877-877-BBOX 724-746-5500 FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 SUPPORT Mailing address: Black Box Corporation , 1000 Park Drive, Lawrence, PA 15055-1018 INFORMATION Web site: www.blackbox.com E-mail: info@blackbox.com...
  • Page 4 FCC AND ICRFI STATEMENTS FEDERAL COMMUNICATIONS COMMISSION INDUSTRY CANADA RADIO FREQUENCY INTERFEREN CE STATEMENTS This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
  • Page 5 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports INSTRUCCIONES DE SEGURIDAD (Normas Oficiales Mexicanas Electrical Safety Statement) 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.
  • Page 6 Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners. NOTE The 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports is called the LPB200A in the software screens and also in the screens shown in this manual. Both names refer to the LPB200A switch.

  • Page 7: Table Of Contents

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Contents Chapter Page 1. Specifications ..............................7 1.1 Hardware ..............................7 1.2 Management Software ..........................8 1.3 Null-Modem Cable ...........................9 2. Overview ................................10 2.1 Introduction ............................10 2.2 What’s Included ............................11 2.3 Hardware Description ..........................12 2.4 Optional SFP Fiber Transceiver Modules .....................14...

  • Page 8: Chapter Page

    Contents Chapter Page 4.3.1 Status ............................40 4.3.2 Configuration ..........................43 4.3.3 Simple Counter .........................44 4.3.4 Detail Counter ...........................45 PoE .................................48 4.4.1 PoE Status ..........................49 4.4.2 PoE Configuration ........................49 Mirror ..............................49 Bandwidth Management ........................50 QoS Configuration ..........................51 4.7.1 Per Port Priority .........................51 4.7.2 VLAN Tag Priority ........................51 4.7.3 IP TOS Classification ........................52 4.7.4 IP TCP/UDP Port Classification ....................53...
  • Page 9 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Contents (continued) Chapter Page 4.17 802.1x Configuration ..........................76 4.17.1 802.1x State Setting .........................80 4.17.2 802.1x Mode Setting ........................81 4.17.3 Port Security Management ......................81 4.17.4 Parameter Setting ........................82 4.18 Alarm Configuration ..........................83 4.18.1 Events Configuration ........................83...

  • Page 10: Specifications

    CHAPTER 1: Specifications 1. Specifications 1.1 Hardware Standards: IEEE802.3, 802.3ab, 802.3z, 802.3u, 802.3af Power over Ethernet, 802.1v protocol-based VLAN classification, 802.3x port-based network access control, 802.1q tag-based VLAN, 802.1d Spanning Tree Protocol, 802.1w Rapid Spanning Tree Protocol, 802.1p Class of Service with 2-level priority queuing, 802.1ad port trunking with flexible load distribution and failover function Compatible Fiber Transceiver Modules: Ports 11, 12 are TP/SFP fiber dual-media ports with auto detection function;...

  • Page 11: Management Software

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Power Consumption: Max. 15W ( in case no PD device connected) Max. 135W ( with 8 x 15.4W PoE device connected ) Max. 185W ( with 12 x 15.4W PoE device connected ) Size: 1.7"H x 17.4"W x 8.2"D (4.4 x 44.2 x 20.9 cm)

  • Page 12: Null-Modem Cable

    CHAPTER 1: Specifications 1.3 Null-Modem Cable Use the included DB9 cable to connect a terminal or terminal emulator to the managed switch’s RS-232 port to access the command-line interface. Table 1-1 shows the pin assignments for the DB9 cable. Table 1-1. Command-line interface DB9 connector pin out. Function Carrier (CD) Receive Data (RXD)

  • Page 13: Overview

    2. Overview 2.1 Introduction The 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports is standard switch that meet all IEEE 802.3/u/x/z Gigabit and Fast Ethernet specifications. Manage the switch via an async console directly connected to the switch’s RS-232 port, or through an Ethernet port using CLI or SNMP. In this switch, ports 11, 12 include two types of media --- TP and SFP Fiber (LC, BiDi LC, etc);...

  • Page 14: What's Included

    2.2 What’s Included Your package should contain the following items. If anything is missing or damaged, please contact Black Box at 724-746-5500. • 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports •...

  • Page 15: Hardware Description

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 2.3 Hardware Description Figure 2-1 shows the 12-Port 1000BASE-TX L2 Managed PoE Switch’s front panel. The numbered components in the figure are described in Table 2-1. Figure 2-1. Front panel.
  • Page 16 CHAPTER 2: Overview Table 2-1 (continued). Front-panel components. Component Description Reset button Resets the management system. Gigabit TP Ports 12 10/100/1000Mbps TP ports. 2 SFP fiber port module slots. SFP Fiber Ports The switch’s rear panel is shown in Figure 2-2. The numbered components in the figure are described in Table 2-2.

  • Page 17: Optional Sfp Fiber Transceiver Modules

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 2.4 Optional SFP Fiber Transceiver Modules Ports 11, 12 on the LPB200A include two types of media: twisted-pair (TP) and optional small form factor pluggable (SFP) fiber (LC, BiDi LC, etc.) modules. The twisted-pair ports are the switch’s two rightmost RJ-45 twisted-pair connectors (ports 11, 12).

  • Page 18: Installation

    CHAPTER 3: Installation 3. Installation 3.1 Installation Instructions CAUTION Wear a grounding device to avoid damage from electrostatic discharge. Be sure that the power switch is OFF before you connect the power cord to the power source. INSTALLING THE OPTIONAL MODULES NOTE If you do not plan to install SFP fiber transceivers in the switch’s ports 11, 12, skip this section.

  • Page 19: Installing The Chassis In A 19-Inch Wiring Closet Rail

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Installing the Rubber Feet For this switch, install the rubber feet and place it on a desktop, or install the switch in the rack with mounting hardware (see Section3.2).

  • Page 20: Cabling Requirements

    CHAPTER 3: Installation 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Figure 3-2. Installing the switch chassis in a 19"rack. 3.3 Cabling Requirements 3.3.1 T WISTED ORTS For Fast Ethernet or Gigabit Ethernet twisted-pair (TP) connections, use CAT5 or CAT5e cable up to 328 feet (100 m) long.
  • Page 21 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 3-1. Cable’s bit-time (round-trip) delay. 1000BASE-X TP , Fiber 1000BASE-TX TP 100BASE-FX Fiber Round-Trip Delay: 4096 Round-Trip Delay: 512 Cat. 5 TP Wire: 11.12/m Cat. 5 TP Wire: 1.12/m Fiber Cable: 1.0/m...
  • Page 22 The switch supports both port-based VLAN and tag-based VLAN. They are different in practical deployment, especially in physical location. Figures 3-4 and 3-5 show a port-based VLAN and Figure 3-6 shows an attribute-based VLAN. 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports VLAN 1 VLAN 2...
  • Page 23 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Example 3: Another Port-Based VLAN 12-Port 1000BASE-TX L2 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 Managed PoE Switch with 2 SFP Dual Media Ports SFP Dual Media Ports...

  • Page 24: Configuring The Management Agent

    CHAPTER 3: Installation Example 4. The same VLAN members can be at different switches with the same VID 12-Port 1000BASE-TX L2 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 Managed PoE Switch with 2 SFP Dual Media Ports SFP Dual Media Ports VLAN 1 VLAN 2 VLAN 3...

  • Page 25: Via The Serial Rs-232 Console Port

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 3.4.1 V RS-232 C ERIAL ONSOLE To configure the switch through its serial RS-232 console port, the port must be directly connected to a DCE device (for example, a PC, through an RS-232 cable with a DB9 connector). See Figure 3-7.
  • Page 26 After completing these settings, reboot it so the configuration takes effect. After this step, operate the management through the network, either from a Web browser or Network Management System (NMS). See Figure 3-8. Copyright (c) 1981–2005 Black Box Corp. L2 Managed Switch LPB200A...

  • Page 27: Via The Ethernet Port

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 3.4.2 V THERNET There are three ways to configure and monitor the switch through the switch’s Ethernet port: CLI, Web browser, and SNMP management. The user interface for SNMP is NMS dependent and is not described here.

  • Page 28: Ip Address Assignment

    CHAPTER 3: Installation 3.5 IP Address Assignment For IP address configuration, you will need the switch’s IP address, subnet mask, default gateway, and DNS. 3.5.1 IP A DDRESS The network device’s address is used for internetworking communication. The 32-bit address consists of a network identifier and a host identifier.

  • Page 29: Subnet Mask

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 3.5.2 S UBNET Subnet mask is the sub-division of a class-based network or a CIDR block. The subnet is used to determine how to split an IP address to the network prefix and the host address. It’s designed to use an IP address more efficiently to manage an IP network.

  • Page 30: Default Gateway

    CHAPTER 3: Installation 3.5.3 D EFAULT ATEWAY For the routed packet, if the destination is not in the routing table, all the traffic is put into the device with the designated IP address, known as the default router. Only the switch uses the gateway setting for Trap Events Host.

  • Page 31: Remote Site/Central Site Connection

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 3.6.1 FTTB/FTTO C ONNECTION Figure 3-10 shows a FTTB/FTTO application is used in carrier or ISP. Figure 3-10. Network Connection of FTTB/FTTO.

  • Page 32: Peer-To-Peer Network Connection

    CHAPTER 3: Installation 3.6.2 FTTH C ONNECTION Figure 3-11 shows a FTTH application is used in carrier or ISP. Figure 3-11. Network Connection of FTTH.

  • Page 33: Office Network Connection

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 3.6.3 D AISY HAIN IBER ETWORK ONNECTION Figure 3-12 shows the Daisy-Chain Fiber Network Connection. Figure 3-12. Typical office network using three switches.

  • Page 34: Web-Based Management

    CHAPTER 4: Web-Based Management 4. Web-Based Management This chapter explains how to configure and manage the switch through the Web user interface. Via one switch port, you can easily access and monitor the switch’s status, including MIBs, port activity, spanning tree, port aggregation, multicast traffic, VLAN and priority, and even a record of illegal access to the network.

  • Page 35: Home Overview

    CLI login screen. The system then displays a serial number. Write down this serial number and contact Black Box—we’ll give you a temporary password. Type in this new password as ID and Password, and the system will allow you to temporarily log into the system with manager authority. This password allows you to login to the system only one time, so modify your password immediately after you log into the system successfully.
  • Page 36 CHAPTER 4: Web-Based Management Table 4-3. System Information screen settings. Parameter Description Model Name LPB200A System Description 12-Port 1000BaseT/TX Managed PoE Switch. Location The user-defined switch location. Contact This is the contact name and phone number for help. Configure this parameter via the switch’s user interface or SNMP.

  • Page 37: Ip Configuration

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 4.2.2 IP C ONFIGURATION IP configuration is one of the most important switch configurations. Without the proper setting, the network manager will not be able to manage or view the device. The switch supports both manual IP address setting and automatic IP address setting via a DHCP server.

  • Page 38: Time Configuration

    CHAPTER 4: Web-Based Management Table 4-4 (continued). IP Configuration screen options. Parameter Description Subnet mask (continued) Subnet mask sets the subnet mask value, which should be the same value as that of the other devices residing in the same network that the switch is attached to.
  • Page 39 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-5. Time Configuration screen options. Parameter Description Time Type in the system time or set it by syncing from Time servers. The function also supports daylight savings time for different areas’ time adjustment.

  • Page 40: Account Configuration

    CHAPTER 4: Web-Based Management Table 4-5 (continued). Time Configuration screen options. Parameter Description Daylight saving (continued) The switch supports valid configurable daylight savings time of -5 to+5 step one hour. The zero for this parameter means it does not have to adjust current time; it’s equivalent to activating daylight saving.

  • Page 41: Management Policy

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports The default setting for administrator user account is: Username: admin Password: admin The default setting for guest user account is: Username: guest Password: guest 4.2.5 M ANAGEMENT OLICY Limiting User Access to the Switch Through the management security configuration, the administrator can control the switch and limit the user’s...

  • Page 42: Virtual Stack

    CHAPTER 4: Web-Based Management Table 4-7. Management Security Configuration settings. Parameter Description Name A name is composed of any letter (A–Z, a–z) and digit (0–9) with a maximum of 8 characters. VID supports two buttons for managed valid VLAN VID: Any and Custom.

  • Page 43: Port Configuration

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports an SNMP or Telnet user interface, VSM is only available in a Web user interface (UI). While one switch is the Master, two rows of buttons for a group device will appear on the top of its Web UI. Press the buttons to connect the group devices’...
  • Page 44 CHAPTER 4: Web-Based Management Table 4-9. Port Configuration menu options. Parameter Description Port Status Report the latest updated status of all switch ports. When any one of the ports in the switch changes its parameter displayed in the page, the port status will automatically refresh about every 5 seconds. Port No.
  • Page 45 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-9 (continued). Port Configuration menu options. Parameter Description Speed/Duplex Mode Display the speed and duplex of all port. There are three speeds 10Mbps, 100Mbps and 1000Mbps supported for TP media, and the duplex supported is half duplex and full duplex.

  • Page 46: Configuration

    CHAPTER 4: Web-Based Management Table 4-10 (continued). Ports 11--12. Parameter Description Vendor OUI Displays the Manufacturer's OUI code that’s assigned by IEEE. Vendor Name Displays the module manufacturer’s company name. Vendor P/N Displays the manufacturer’s switch’s part number. Vendor Rev (Revision) Displays the module revision.

  • Page 47: Simple Counter

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-11 (continued). Configuration screen options. Parameter Description Mode Set the speed and duplex of the port. In speed, 10/100Mbps baud rate is available for Fast Ethernet, Gigabit module in port 11, 12. If the media is 1Gbps fiber, it is always 1000Mbps and the duplex is full only.

  • Page 48: Detail Counter

    CHAPTER 4: Web-Based Management Table 4-12. Simple Counter screen options. Parameter Description Simple Counter Displays each port’s traffic summary counting, including Tx Byte, Rx Byte, Tx Packet, Rx Packet, Tx Collision, and Rx Error Packet. Refresh Interval Select a number (in seconds) from the drop-down menu. Reset button Click on this button to reset the simple counter.
  • Page 49 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-13. Detail Counter screen options. Parameter Description Detail Counter Displays the detailed counting number of each port’s traffic. The Detail Counter window can show all counter information of each port at onetime.
  • Page 50 CHAPTER 4: Web-Based Management Table 4-13 (continued). Detail Counter screen options. Parameter Description Rx 128-255 Bytes Number of 127 ~ 255-byte frames in good and bad packets received. Rx 256-511 Bytes Number of 256 ~ 511-byte frames in good and bad packets received. Number of 512 ~ 1023-byte frames in good and bad packets Rx 512-1023 Bytes received.

  • Page 51: Poe

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 4.4 PoE 4.4.1 POE S TATUS Table 4-14 shows all the parameters of the PoE status. Table 4-14 PoE screen options. Parameter Description PoE Status Display the information about the PoE status.

  • Page 52: Poe Configuration

    CHAPTER 4: Web-Based Management 4.4.2 POE C ONFIGURATION The switch complies with IEEE 802.3af protocol and be capable of detecting automatically that whether the device linked to the port on the switch is PD (Powered Device) or not. The switch also manage the power supplement based on the Class of the PD, and it will stop supplying the power once the power required by the PD excesses the Class, Short Circuit or over temperature occurs.

  • Page 53: Bandwidth Management

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-16. Mirror Configuration screen settings. Parameter Description Mode Used for the activation or de-activation of Port Mirror function. Default is disable. Monitoring Port Set up the port for monitoring. Valid port is Port 1~12 and default is Port 1.

  • Page 54: Qos Configuration

    CHAPTER 4: Web-Based Management 4.7 QoS (Quality of Service) Configuration The switch offers powerful 5 kinds of QoS functions. There are Per Port Priority that you can assign each port to different precedence, VLAN Tag priority that can make precedence of 8 priorities, IP TOS Classification, IP TCP/UDP Port Classification and IP DiffServe Classification.

  • Page 55: Ip Tos Classification

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-19. VLAN Tag Priority screen options. Parameter Description Quality of Service (QoS) Vlan Used for setting up the QoS belongs to Vlan operation. Tag Configuration Port User can set up the port (1~12) respectively to let Vlan Tag QoS function work on them.

  • Page 56: Ip Tcp/Udp Port Classification

    CHAPTER 4: Web-Based Management 4.7.4 IP TCP/UDP P LASSIFICATION In L4 QoS Configuration, you can enter one of these special network transmission events, for example we use Down prioritize web browsing, e-mail, FTP and news L4 QoS Configuration and click Apply button, and then click Advance button.
  • Page 57 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-21 (Continued). IP TCP/UDP Port Classification screen options. Parameter Description Advanced Mode Display the TCP/UDP port number in L4 QoS. In “Disable IP TCP/UDP Port Classification” mode, user can randomly choose TCP/UDP port number that L4 QoS will affect.

  • Page 58: Ip Diffev Classification

    CHAPTER 4: Web-Based Management 4.7.5 IP D IFFSERV LASSIFICATION In the late 1990s, the IETF redefined the meaning of the 8-bit SERVICE TYPE field to accommodate a set of differentiated services (DS). Under the differentiated services interpretation, the first six bits comprise a codepoint, which is sometimes abbreviated DSCP, and the last two bits are left unused.
  • Page 59 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-23 (Continued). SNMP Configuration screen options. Parameter Description SNMP The term SNMP here is used for the activation or de-activation of SNMP. Default is Enable. Get/Set/Trap Community...

  • Page 60: Igmp Snooping

    CHAPTER 4: Web-Based Management 4.9 IGMP Snooping The function, IGMP Snooping, is used to establish the multicast groups to forward the multicast packet to the member ports, and, in nature, avoids wasting the bandwidth while IP multicast packets are running over the network.

  • Page 61: Max Packet Length

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-24 (Continued). IGMP Snooping screen options. Parameter Description IP Address Show all multicast groups IP addresses that are registered on this device. VLAN ID Show VLAN ID for each multicast group.

  • Page 62: Vlan Mode

    CHAPTER 4: Web-Based Management 4.12.1 VLAN M The VLAN Mode Selection function includes five modes: Port-based, Tag- based, Metro Mode, Double-tag and Disable, you can choose one of them by pulling down list and selecting an item. Then, click Apply button, the settings will take effect immediately.

  • Page 63: Tag-Based Group

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 4.12.2 T ASED ROUP It shows the information of existed Tag-based VLAN Groups, You can also easily create, edit and delete a Tag-based VLAN group by pressing Add, Edit and Delete function buttons. User can add a new VLAN group by inputting a new VLAN name and VLAN ID.

  • Page 64: Tag Rule

    CHAPTER 4: Web-Based Management Table 4-28. Port-Based Group screen options. Parameter Description VLAN Name The name defined by administrator is associated with a VLAN group. Valid letters are A-Z, a-z, 0-9, “ - “ and “_” characters. The maximal length is 15 characters. Member This is used to enable or disable if a port is a member of the new added VLAN, “Enable”...

  • Page 65: Mac Table

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-29 (Continued). Tag Rule screen options. Parameter Description Rule 2 Drop untagged frame. You can configure a given port to accept all frames (Tagged and Untagged) or just receive tagged frame. If the former is the case, then the packets with tagged or untagged will be processed.

  • Page 66: Mac Table Maintenance

    CHAPTER 4: Web-Based Management Table 4-30 (continued). MAC Table screen options. Parameter Description Display the MAC address of one entry you selected from the searched MAC entries table. Alias Set up the Alias for the selected MAC entry. Set Alias Save the Alias of MAC entry you set up.

  • Page 67: Static Forward

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 4.13.3 STATIC FORWARD Static Forward is a function that allows the user in the static forward table to access a specified port of the switch. Static Forward table associated with a specified port of a switch is set up by manually inputting MAC address and its alias name.

  • Page 68: Mac Alias

    CHAPTER 4: Web-Based Management 4.13.5 MAC A LIAS MAC Alias function is used to let you assign MAC address a plain English name. This will help you tell which MAC address belongs to which user in the illegal access report. At the initial time, it shows all pairs of the existed alias name and MAC address.

  • Page 69: Gvrp Config

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 4.14.1 GVRP C ONFIG Table 4-33. GVRP Configuration screen options. Parameter Description GVRP Config In the function of GVRP Config, it is used to configure each port’s GVRP operation mode, in which there are seven parameters needed to be configured described below.

  • Page 70: Gvrp Counter

    CHAPTER 4: Web-Based Management Table 4-33 (Continued). GVRP Configuration screen options. Parameter Description Default Registrar Mode The mode here means the type of Registrar. There are three types of parameters for registrar administrative control value, normal registrar, fixed registrar and forbidden registrar, provided for the user’s choice.

  • Page 71: Gvrp Group Information

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-34 (Continued). GVRP Counter screen options. Parameter Description JoinEmpty Message Packets Number of GARP BPDU with Join Empty message is received/ transmitted by the GARP application. JoinIn Message Packets Number of GARP BPDU with Join In message is received/ transmitted by the GARP application.

  • Page 72: Stp Status

    CHAPTER 4: Web-Based Management 4.15.1 STP S TATUS In the Spanning Tree Status, user can read 12 parameters to know STP current status. The 12 parameters’ description is listed in the following table. Table 4-36. STP Status screen options. Parameter Description STP State Show the current STP Enabled / Disabled status.

  • Page 73: Stp Configuration

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-36 (Continued). STP Status screen options. Parameter Description STP Topology Change Count STP Topology Change Count expresses the time spent in unit of seconds since the beginning of the Spanning Tree Topology Change to the end of the STP convergence.

  • Page 74: Stp Port Configuration

    CHAPTER 4: Web-Based Management Table 4-37 (Continued). STP Configuration screen options. Parameter Description Max. Age When the LPB200A is the root bridge, the whole LAN will apply this figure set by this switch as their maximum age time. When a bridge received a BPDU originated from the root bridge and if the message age conveyed in the BPDU exceeds the Max.
  • Page 75 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4- 38. STP Port setting screen options. Parameter Description Port Status It displays the current state of a port. We cannot manually set it because it displays the status only. There are three possible states.

  • Page 76: Trunking Information

    CHAPTER 4: Web-Based Management 4.16 Trunking Configuration The Port Trunking Configuration is used to configure the settings of Link Aggregation. You can bundle more than one port with the same speed, full duplex and the same MAC to be a single logical port, thus the logical port aggregates the bandwidth of these ports.

  • Page 77: Port Setting Status

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 4.16.1 P ETTING TATUS Port setting/status is used to configure the trunk property of each and every port in the switch system. Table 4-39. Port Setting/ Status screen options.

  • Page 78: Aggregator View

    CHAPTER 4: Web-Based Management 4.16.2 A GGREGATOR To display the current port trunking information from the aggregator point of view. Table 4-40. Aggregator View screen options. Parameter Description Aggregator It shows the aggregator ID (from 1 to 12) of every port. In fact, every port is also an aggregator, and its own aggregator ID is the same as its own Port No.

  • Page 79: Lacp System Config

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 4.16.3 LACP S YSTEM ONFIG It is used to set the priority part of the LACP system ID. LACP will only aggregate together the ports whose peer link partners are all on a single system. Each system supports LACP will be assigned a globally unique System Identifier for this purpose.
  • Page 80 CHAPTER 4: Web-Based Management A port acting as an authenticator is thought to be two logical ports, a controlled port and an uncontrolled port. A controlled port can only pass the packets when the authenticator PAE is authorized, and otherwise, an uncontrolled port will unconditionally pass the packets with PAE group MAC address, which has the value of 01-80-c2-00-00-03 and will not be forwarded by MAC bridge, at any time.
  • Page 81 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Authentication server Authenticator Supplicant A Figure 4-2. The Fig. 4-3 shows the procedure of 802.1x authentication. There are steps for the login based on 802.1x port access control management. The protocol used in the right side is EAPOL and the left side is EAP.
  • Page 82 CHAPTER 4: Web-Based Management 9. When the authenticator PAE receives a Radius-Access-Accept, it will send an EAP-Success to the supplicant. At this time, the supplicant is authorized and the port connected to the supplicant and under 802.1x control is in the authorized state. The supplicant and other devices connected to this port can access the network.

  • Page 83: State Setting

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-43. Port Mode Port Control Authentication Port Status Disable Don’t Care Don’t Care Port Uncontrolled Multihost Auto Successful Port Authorized Multihost Auto Failure Port Unauthorized Multihost ForceUnauthorized Don’t Care...

  • Page 84: Mode Setting

    CHAPTER 4: Web-Based Management 4.17.2 802.1x M ETTING Set the operation mode of 802.1X for each port. In this device, it supports only Multi-host operation mode. Table 4-45. 802.1x Mode Setting screen options. Parameter Description Port Number Indicate which port is selected to configure the 802.1x operation mode.

  • Page 85: Parameter Setting

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 4.17.4 P ARAMETER ETTING This function is used to configure the parameters for each port in 802.1x port security application. Refer to the following parameters description for details.

  • Page 86: Alarm Configuration

    CHAPTER 4: Web-Based Management Table 4-47 (continued). Parameter Setting screen options. Parameter Description max. Request (1-10) The maximum of number times that the authenticator will retransmit an EAP Request to the supplicant before it times out the authentication session. The valid range: 1 – 10. Default: 2 times suppTimeout (1-65535 s) A timeout condition in the exchange between the authenticator and...

  • Page 87: E-Mail/Sms Configuration

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 4.18.2 E MAIL ONFIGURATION Alarm configuration is used to configure the persons who should receive the alarm message via either email or SMS, or both. It depends on your settings. An email address or a mobile phone number has to be set in the web page of alarm configuration (See Fig.

  • Page 88: Save/Restore

    CHAPTER 4: Web-Based Management User Configuration This is the configuration file for the specified or backup purposes. It can be updated while confirming the configuration. Retrieve it by performing Restore User Configuration 4.19.1 S ESTORE To get to this screen, click on Save/Restore in the Configuration menu. Table 4-50.

  • Page 89: Diagnostics

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Table 4-51 (Continued). Config File screen options. Parameter Description Import File Path Import Start button: Import Save As Start’s config file stored in the Flash. Import User-Conf button: Import Save As User’s config file stored in the Flash.

  • Page 90: Tftp Server

    CHAPTER 4: Web-Based Management 4.21 TFTP Server You can set up IP address of TFTP server in this page. Table 4-53. TFTP Server screen options. Parameter Description Server Specify the IP address where the TFTP server locates. Fill in the IP address of your TFTP server, then press Apply button to have the setting taken effect.

  • Page 91: Reboot

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Then, press Upgrade button if your download is not successful, the switch will also be back to “Software Upgrade”, and it will not upgrade the software as well.

  • Page 92: Logout

    CHAPTER 4: Web-Based Management 4.25 Logout You can manually logout by performing Logout function. In the switch, it provides another way to logout. You can configure it to logout automatically. The switch allows you to logout the system to prevent other users from the system without the permission. If you do not logout and exit the browser, the switch will automatically have you logout.

  • Page 93: Cli Management

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 5. CLI Management Locate the included RS-232 null-modem cable. Refer to Section 1.3for the null-modem cable’s configuration. Attach the DB9 female connector to the male DB9 serial port connector on the switch.

  • Page 94: Global Cli Commands

    CHAPTER 5: CLI Management Giga Switch — LPB200A Login: admin Password: LPB200A# ? 802.1x Enter into 802.1x mode account Enter into account mode alarm Enter into alarm mode autologout Change autologout time bandwidth Enter into bandwidth mode config-file Enter into config file moded dhcp-boot Enter into dhcp-boot mode diag...
  • Page 95 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports exit Syntax: exit Description: Return to the previous mode. When you enter this command, your current position moves back to the previous mode. Argument: None Possible value: None...
  • Page 96 CHAPTER 5: CLI Management exit Back to the previous mode Back to the top mode help Show available commands history Show a list of previously run commands logout Logout the system save start Save as start config save user Save as user config restore default Restore default config restore user...
  • Page 97 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Giga Switch(ip)# history 3 Command history: 13. ip 14. history 15. history 3 Giga Switch(ip)# logout Syntax: logout Description: When you enter this command via a Telnet connection, you will log out of the system and disconnect.
  • Page 98 CHAPTER 5: CLI Management restore user Syntax: restore user Description: Restores the startup configuration as a user-defined configuration. If restoring default is successful, the CLI asks if you want to reboot immediately or not. Pressing Y or y reboots the system immediately; if you press N or n, the software returns to the CLI system.

  • Page 99: Local Cli Commands

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Possible value: None Example: Giga Switch# save user Saving user... Save Successfully Giga Switch# 5.2.2 L CLI C OCAL OMMANDS NOTE For local CLI commands, syntax 1, 5–7 represents a range of ports. For example, if the port range is shown as 1, 5–7, available from 1 to 12, the range of ports available is 1–8.
  • Page 100 CHAPTER 5: CLI Management Possible value: <port range> : 1 to 12 <mode>: 0 or 1 Example: Giga Switch(802.1X)# set mode 2 1 set port-control Syntax: set port-control <port-range> <authorized> Description: Sets up each port’s 802.1x status. Argument: <port range> : syntax 1, 5–7, available from 1 to 12 <authorized>...
  • Page 101 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Example: Giga Switch(802.1X)# set quiet-period 2 30 set reAuthEnabled Syntax: set reAuthEnabled <port-range> <ebl> Description: A constant that defines whether regular reauthentication will occur on this port. Argument: <port range>...
  • Page 102 CHAPTER 5: CLI Management set reAuthPeriod Syntax: set reAuthPeriod <port-range> <sec> Description: A constant that defines a nonzero number of seconds between the Supplicant’s periodic reauthentication. Argument: <port range> : syntax 1, 5–7, available from 1 to 12 <sec> : timer, range 1–65535 Possible value: <port range>...
  • Page 103 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports set state Syntax: set state <ip> <port-number> <secret-key> Description: Configures the settings related to the 802.1x Radius Server. Argument: <ip> : the IP address of Radius Server <port-number> : the service port of Radius Server (Authorization port) <secret-key>...
  • Page 104 CHAPTER 5: CLI Management set txPeriod Syntax: set txPeriod <port-range> <sec> Description: A timer used by the Authenticator state machine to determine when a packet will be transmitted. Argument: <port range> : syntax 1, 5–7, available from 1 to 12 <sec>...
  • Page 105 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports show parameter Syntax: show parameter Description: Displays each port’s parameter settings. Argument: None Possible value: None Example: Giga Switch(802.1X)# show parameter port 1) port control : Auto reAuthMax...
  • Page 106 CHAPTER 5: CLI Management Example: Giga Switch(802.1X)# show security Port Mode Status ====== ============ ============== Disable Multi-host Unauthorized Disable Disable Disable Disable show state Syntax: show state Description: Shows the Radius server’s configuration. Argument: None Possible value: None Example: Giga Switch(802.1X)# show state Radius Server: 192.168.1.115 Port Number : 1812 Secret Key : WinRadius...
  • Page 107 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Example: Giga Switch(account)# add aaaaa Password: Confirm Password: Save Successfully Giga Switch(account)# Syntax: del <name> Description: Deletes an existing account. Argument: <name> : existing user account Possible value: None...
  • Page 108 CHAPTER 5: CLI Management show Syntax: show Description: Shows a system account, including account name and identity. Argument: None Possible value: None Example: Giga Switch(account)# show Account Name Identity -------------------------------- admin Administrator guest guest alarm <<email>> del mail-address Syntax: del mail-address <#> Description: Removes the email address configuration.
  • Page 109 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports set mail-address Syntax: set mail-address <#> <mail address> Description: Sets up the email address. Argument: <#> :email address number, range of 1 to 6 <mail address>:email address Possible value: <#>: 1 to 6...
  • Page 110 CHAPTER 5: CLI Management show Syntax: show Description: Displays the e-mail configuration. Argument: None Possible value: None Example: Giga Switch(alarm-email)# show Mail Server: 192.168.1.6 Username: admin Password: **************** Email Address 1: abc@mail.abc.com Email Address 2: Email Address 3: Email Address 4: Email Address 5: Email Address 6: <<events>>...
  • Page 111 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports del email Syntax: del email <range> Description: Disables the events’ email. Argument: <range>:del the range of email, syntax 1, 5–7 Possible value: <range>: 1–24 Example: Giga Switch(alarm-events)# del email 1-3 del sms Syntax: del sms <range>...
  • Page 112 CHAPTER 5: CLI Management set all Syntax: set all <range> Description: Enables email, sms, and events’ trap. Argument: <range>:set the range of events, syntax 1, 5–7 Possible value: <range>: 1–26 Example: Giga Switch(alarm-events)# set all 1-3 set email Syntax: set email <range> Description: Enables the events’...
  • Page 113 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Possible value: <range>: 1–26 Example: Giga Switch(alarm-events)# set trap 1-3 show Syntax: show Description: Displays the alarm event’s configuration. Argument: None Possible value: None Example: Giga Switch(alarm-events)# show...
  • Page 114 CHAPTER 5: CLI Management show (alarm) Syntax: show Description: Displays the trap, SMS, or e-mail configuration. Argument: None Possible value: None Example: Giga Switch(alarm)# show events Giga Switch(alarm)# show email Giga Switch(alarm)# show sms <<sms>> del phone-number Syntax: del phone-number <#> Description: Deletes the sms’...
  • Page 115 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports set phone-number Syntax: set phone-number <#> <phone-number> Description: Adds sms phone number. Argument: <#>: mobile phone number, range of 1 to 6 <phone-number>: phone number Possible value: <#>: 1 to 6...
  • Page 116 CHAPTER 5: CLI Management show Syntax: show Description: Displays the SMS trap event’s configuration. Argument: None Possible value: None Example: Giga Switch(alarm-sms)# show SMS Server: 192.168.1.7 Username : ABC Password : **************** Mobile Phone 1: 0968777777 Mobile Phone 2: Mobile Phone 3: Mobile Phone 4: Mobile Phone 5: Mobile Phone 6:...
  • Page 117 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports bandwidth disable egress-rate Syntax: disable egress-rate <range> Description: Cancels the port’s Egress rate. Argument: <range>:syntax 1, 5–7, available from 1 to 12 Possible value: <range>: 1 to 12...
  • Page 118 CHAPTER 5: CLI Management enable egress-rate Syntax: enable egress-rate <range> <data_rate> Description: Sets up the port’s Egress rate. Argument: <range>:syntax 1, 5–7, available from 1 to 12 <data_rate>: 0–1000 Possible value: <range>: 1 to 12 <data_rate>: 0–1000 Example: Giga Switch(bandwidth)# enable egress-rate 1-8 200 enable ingress-rate Syntax: enable ingress-rate <range>...
  • Page 119 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Argument: <range>:syntax 1, 5–7, available from 1 to 12 <data_rate>: 0–1000 Possible value: <range>: 1 to 12 <data_rate>: 0–1000 Example: Giga Switch(bandwidth)# enable storm-rate 1-8 150 show Syntax: show Description: Displays all current bandwidth settings.
  • Page 120 CHAPTER 5: CLI Management config-file export start Syntax: export start Description: Runs the export start function. Argument: None Possible value: None Example: Giga Switch(config-file)# export start Export successful. export user-conf Syntax: export user-conf Description: Runs the export user-conf function. Argument: None Possible value: None Example: Giga Switch(config-file)# export user-conf...
  • Page 121 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports import user-conf Syntax: import user-conf Description: Runs the import user-conf function. Argument: None Possible value: None Example: Giga Switch(config-file)# import user-conf Import successful. set export-path Syntax: set export-path <filepath>...
  • Page 122 CHAPTER 5: CLI Management show Syntax: show Description: Displays the config-file information. Argument: None Possible value: None Example: Giga Switch(config-file)# show TFTP Server IP Address: 192.168.3.111 Export Path and Filename: nmap/123.ts Import Path and Filename: user123.txt dhcp-boot set dhcp-boot Syntax: set dhcp-boot <sec> Description: Sets up the DHCPBoot delay time.
  • Page 123 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports diag diag Syntax: diag Description: Tests whether UART, DRAM, Flash, and EEPROM are normal or not. Argument: None Possible value: None Example: Giga Switch(diag)# diag EEPROM Test: OK...
  • Page 124 CHAPTER 5: CLI Management Example: Giga Switch(diag)# ping 192.168.1.115 Gateway: 192.168.1.253 192.168.1.115 is alive. firmware set upgrade-path Syntax: set upgrade-path <filepath> Description: Sets up the image file that will be upgraded. Argument: <filepath>: upgrade file path Possible value: <filepath>: upgrade file path Example: Giga Switch(firmware)# set upgrade-path gs2108c_Giga Switch_v2.03.img show...
  • Page 125 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Example: Giga Switch(firmware)# upgrade Upgrading firmware ... gvrp disable Syntax: disable Description: Disables the gvrp function. Argument: None Possible value: None Example: Giga Switch(gvrp)# disable enable Syntax: enable Description: Enables the gvrp function.
  • Page 126 CHAPTER 5: CLI Management Example: Giga Switch(gvrp)# show group GVRP group information Current Dynamic Group Number: 1 Member Port ---- -------------------------------------------------- Giga Switch(gvrp)# group 2 Giga Switch(gvrp-group-2)# set applicant 1-6 non-participant Giga Switch(gvrp-group-2)# show GVRP group VID: 2 Port Applicant Registrar ---- ---------------...
  • Page 127 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Possible value: <range>: 1 to 12 <normal|non-participant>: normal or non-participant Example: Giga Switch(gvrp)# set applicant 1-8 non-participant set registrar Syntax: set registrar <range> <normal|fixed|forbidden> Description: Sets each port’s default registrar mode.
  • Page 128 CHAPTER 5: CLI Management Example: Giga Switch(gvrp)# set restricted 1-8 enable Giga Switch(gvrp)# show config GVRP state: Enable Port Join Time Leave Time LeaveAll Time Applicant Registrar Restricted ---- --------- ---------- --------- ---- --------- --------- ---------- 1000 Normal Normal Enable 1000 Normal Normal Enable...
  • Page 129 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Possible value: None Example: Giga Switch(gvrp)# show config GVRP state: Enable Port Join Time Leave Time LeaveAll Time Applicant Registrar Restricted ---- --------- ---------- ------------- --------- --------- ----------...
  • Page 130 CHAPTER 5: CLI Management Possible value: None Example: Giga Switch(gvrp)# show group GVRP group information Member Port ---- ------------------------------------------------- hostname hostname Syntax: hostname <name> Description: Sets up the switch’s hostname. Argument: <name>: hostname, maximum of 40 characters Possible value: <name>: hostname, maximum of 40 characters Example: Giga Switch# hostname Company Company#...
  • Page 131 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports show Syntax: show Description: Displays the IGMP snooping mode and IP Multicast Table. Argument: None Possible value: None Example: Giga Switch(igmp)# show Snoop Mode: Active IP Multicast: 1) IP Address: 224.1.1.1...
  • Page 132 CHAPTER 5: CLI Management set dns Syntax: set dns <ip> Description: Sets the DNS server’s IPaddress. Argument: <ip> : dns ip address Possible value: 168.95.1.1 Example: Giga Switch (ip)# set dns 168.95.1.1 set ip Syntax: set ip <ip> <mask> <gateway> Description: Sets the system IP address, subnet mask, and gateway.
  • Page 133 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Example: Giga Switch(ip)# show DHCP: Disable IP Address: 192.168.2.237 Current IP Address: 192.168.2.237 Subnet mask: 255.255.255.0 Gateway: 192.168.2.252 DNS Setting: Manual DNS Server: 168.95.1.1 clear Syntax: clear Description: Clears the log data.
  • Page 134 CHAPTER 5: CLI Management enable auto-upload Syntax: enable auto-upload Description: Enables the auto-upload function. Argument: None Possible value: None Example: Giga Switch(log)# enable auto-upload show Syntax: show Description: Shows a list of trap log events. When any log event happens, it will be recorded and it will use show command in the log function to query.
  • Page 135 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports mac-table <<alias>> Syntax: del <mac> Description: Deletes the MAC alias entry. Argument: <mac> : MAC address, format: 00-02-03-04-05-06 Possible value: <mac> : MAC address Example: Giga Switch(mac-table-alias)# del 00-44-33-44-55-44 Syntax: set <mac>...
  • Page 136 CHAPTER 5: CLI Management Example: Giga Switch(mac-table-alias)# show MAC Alias List MAC Address Alias ----------- --------------------------- 00-02-03-04-05-06 00-33-03-04-05-06 00-44-33-44-55-44 <<information>> search Syntax: search <port> <mac> <vid> Description: Looks for the relative MAC information in the MAC table. Argument: <port> : set up the range of the ports to search for, syntax 1, 5–7, available from 1 to 12 <mac>...
  • Page 137 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Example: Giga Switch (mac-table-information)# show MAC Table List Alias MAC Address Port State ----------- ------------------ ----- ---- --------------- 00-10-db-1d-c5-a0 Dynamic 00-40-f4-89-c9-7f Dynamic 00-e0-18-2b-9d-e2 Dynamic 00-40-c7-d8-00-02 Dynamic <<maintain>> set aging Syntax: set aging <#>...
  • Page 138 CHAPTER 5: CLI Management Possible value: None Example: Giga Switch(mac-table-maintain)# show age-timer : 300 seconds Giga Switch(mac-table-maintain)# <<static-mac>> Syntax: add <mac> <port> <vid> [alias] Description: Adds the static MAC entry. Argument: <mac> : MAC address, format: 00-02-03-04-05-06 <port> : 0–8; 0 means this entry is filtering entry <vid>...
  • Page 139 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Example: Giga Switch(mac-table-static-mac)# del 00-02-03-04-05-06 0 show filter Syntax: show filter Description: Displays the static filter table. Argument: None Possible value: None Example: Giga Switch(mac-table-static-mac)# show filter Static Filtering Entry: (Total 1 item(s))
  • Page 140 CHAPTER 5: CLI Management management Syntax: Usage: set [<name> <value>] [<vid> <value>] [<ip> <value>] [<port> <value>] [<type> <value>] <action> <value> Synopsis: set name Mary vid 20 ip 192.168.1.1-192.168.1.90 port 2–5, 8 type h, s action a Synopsis: set name Mary vid 20 ip 192.168.1.1-192.168.1.90 Description: Saves the adding management policy records.
  • Page 141 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Giga Switch(management-add)# show #: 1 Name: Mary VlanID: 20 IP: 192.168.1.1-192.168.1.90 Type: Http,SNMP Action: Accept Port : 2,3,4,5,8 delete Syntax: delete # Description: Deletes a specific record or range.
  • Page 142 CHAPTER 5: CLI Management Argument: [<name> <value>] ACL entry name [<vid> <value>] VLAN ID [<ip> <value>] IP Range [<port> <value>] Incoming port [<type> <value>] Access type <action> <value> a(ccept) or d(eny) Possible value: [<name> <value>] No default and it must be set [<vid>...
  • Page 143 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports set priority Syntax: set priority <port-range> <priority > Description: To set the PoE priority on ports. Argument: <port-range>：which port(s) you want to set, syntax 1,5-7, available from 1 to 24 <priority>: set priority as 0:Low, 1:Normal, 2:High...
  • Page 144 CHAPTER 5: CLI Management Example: LPB200A(poe)# show Vmain : 48.3 V Imain : 0.0 A Pconsume : 0.0 W Power Limit : 185 W Temperature : 37 'C / 98 'F Port No | 1 2 3 4 5 6 7 8 9 10 11 12 ------------------------- | - - - - - - - - - -- -- -- Port On | X X X X X X X X X X...
  • Page 145 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Port Status State Priority Power(W) Current(mA) Class ---- ------ ------- -------- -------- ----------- ----- 1 Normal Enable Normal 2 Normal Enable Normal 3 Normal Enable Normal 4 Normal Enable...
  • Page 146 CHAPTER 5: CLI Management disable flow-control Syntax: disable flow-control <range> Description: Disables the port’s flow control function. Argument: <range>: syntax 1, 5–7, available from 1 to 12 Possible value: <range>: 1–8, 1–16, or 1–24 Example: Giga Switch (port)# disable flow-control 6 disable state Syntax: disable state <range>...
  • Page 147 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Possible value: <range>: 1–8 Example: Giga Switch (port)# enable state 3-7 set speed-duplex Syntax: set speed-duplex <range> <auto|10half|10full|100half|100full|1Gfull> Description: Sets up all ports’ speed and duplex. Argument: auto: set auto-negotiation mode...
  • Page 148 CHAPTER 5: CLI Management show detail-counter Syntax: show detail-counter <#> Description: Displays each port’s traffic detailed counting number. Argument: <#>: port, available from 1 to 12 Possible value: <#>:1–8 Example: Giga Switch (port)# show detail-counter 5 show sfp Syntax: show sfp <port> Description: Displays the SFP module information.
  • Page 149 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports show simple-counter Syntax: show simple-counter Description: Displays each port’s traffic summary counting. Argument: None Possible value: None Example: Giga Switch (port)# show simple-counter show status Syntax: show status Description: Displays the port’s current status.
  • Page 150 CHAPTER 5: CLI Management Example: Giga Switch(qos)# set advance-layer4 5 2 80 1 0 set default Syntax: set default <class> Description: Sets the packets’ priority class that qos won’t affect. Argument: <class>: class of service setting. 1: high, 0: low Possible value: <class>: 1 or 0 Example: Giga Switch(qos)# set default 1...
  • Page 151 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports <diffserv>: ip diffserv classification Possible value: port/pri_tag/tos/layer4/diffserv Example: Giga Switch(qos)# set mode port set port Syntax: set port <range> <class> Description: Set ports’ class on port-based qos. Argument: <range>...
  • Page 152 CHAPTER 5: CLI Management set simple-layer4 Syntax: set simple-layer4 <#> Description: Sets ports class on simple Layer 4 qos mode. Argument: <#>: layer-4 configuration mode, valid values are as follows: 0: disable ip tcp/udp port classification 1: down prioritize web browsing, e-mail, FTP, and news 2: prioritize ip telephony (VoIP) 3: prioritize iSCSI 4: prioritize web browsing, e-mail, FTP transfers, and news...
  • Page 153 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports show Syntax: show Description: Displays the chosen mode’s information. Argument: None Possible value: None Example: Giga Switch (qos)# show IP Diffserv Classification Default Class:high DiffServ Class DiffServ Class DiffServ Class DiffServ Class...
  • Page 154 CHAPTER 5: CLI Management snmp disable Syntax: disable set-ability disable snmp Description: Disable de-activates snmp or set-community. Argument: None Possible value: None Example: Giga Switch(snmp)# disable snmp Giga Switch(snmp)# disable set-ability enable Syntax: enable set-ability enable snmp Description: Enable activates snmp or set-community. Argument: None Possible value: None Example:...
  • Page 155 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Description: Sets up get-community, set-community, trap host ip, host port, and trap-community. Argument: <#>: trap number <ip>: ip address or domain name <port>: trap port <community>:trap community name Possible value: <#>: 1 to 6...
  • Page 156 CHAPTER 5: CLI Management disable Syntax: disable Description: Disables the STP function. Argument: None Possible value: None Example: Giga Switch(stp)# disable enable Syntax: enable Description: Enables the STP function. Argument: None Possible value: None Example: Giga Switch(stp)# enable MCheck Syntax: MCheck <range> Description: Forces the port to transmit RST BPDUs.
  • Page 157 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports set config Syntax: set config <Bridge Priority> <Hello Time> <Max. Age> <Forward Delay> Description: Sets up the STP parameters. Argument: <Bridge Priority>: priority must be a multiple of 4096, available from 0 to 61440 <Hello Time>: available from 1 to 10...
  • Page 158 CHAPTER 5: CLI Management Example: Giga Switch(stp)# set port 1-8 0 128 yes auto set version Syntax: set version <stp|rstp> Description: Sets up the STP version. Argument: <stp|rstp>: stp/rstp Possible value: <stp|rstp>: stp/rstp Example: Giga Switch(stp)# set version rstp show config Syntax: show config Description: Displays the STP configuration.
  • Page 159 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Example: Giga Switch# stp Giga Switch(stp)# show port Port Port Status Path Cost Priority Admin Edge Port Admin Point To Point ==== =========== ========= ======== =============== ==================== DISCARDING...
  • Page 160 CHAPTER 5: CLI Management system set contact Syntax: set contact <contact string> Description: Sets the switch’s contact description. Argument: <contact>:string length up to 40 characters. Possible value: <contact>: A, b, c, d, ... ,z and 1, 2, 3, …. etc. Example: Giga Switch(system)# set contact Taipei set device-name...
  • Page 161 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports show Syntax: show Description: Displays the switch’s basic information. Argument: None Possible value: None Example: Giga Switch(system)# show Model Name : Giga Switch System Description : L2 Managed Switch...
  • Page 162 CHAPTER 5: CLI Management show Syntax: show Description: Displays the tftp server’s information. Argument: None Possible value: None Example: Giga Switch(tftp)# show Tftp Server : 192.168.3.111 time set daylightsaving Syntax: set daylightsaving <hr> <MM/DD/HH> <mm/dd/hh> Description: Sets up the daylight saving. Argument: : daylight saving hour, range: -5 to +5 : daylight saving start Month (01-12)
  • Page 163 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports set manual Syntax: set manual <YYYY/MM/DD> <hh:mm:ss> Description: Sets up the current time manually. Argument: YYYY : Year (2000-2036) MM : Month (01-12) : Day (01-31) hh : Hour (00-23)
  • Page 164 CHAPTER 5: CLI Management Argument: None Possible value: None Example: Giga Switch(time)# show Current Time : Thu Thu 14 15:04:03 2005 NTP Server : 209.81.9.7 Timezone : GMT+8:00 Day light Saving : 0 Hours Day light Saving Start : Mth: 1 Day: 1 Hour: 0 Day light Saving End : Mth: 1 Day: 1 Hour: 0 trunk...
  • Page 165 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports set trunk Syntax: set trunk <port-range> <method> <group> <active LACP> Description: Sets up the trunk status, including the group number and trunk mode as well as LACP mode.
  • Page 166 CHAPTER 5: CLI Management show lacp-detail Syntax: show lacp-detail <aggtr> Description: Displays the LACP trunk group’s detailed information. Argument: <aggtr>: aggregator, available from 1 to 12 Possible value: <aggtr>: 1 to 12 Example: Giga Switch(trunk)# show lacp-detail 2 Aggregator 2 Information: Actor Partner --------------------------------- ---------------------------------...
  • Page 167 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Example: Giga Switch(trunk)# show status Trunk Port Setting Trunk Port Status --------------------------- ------------------------- port Method Group Active LACP Aggregator Status ==== ====== ===== =========== ========== ============ None Active...
  • Page 168 CHAPTER 5: CLI Management disable drop-untag Syntax: disable drop-untag <range> Description: Does not drop the untagged frames. Argument: <range> : which port(s) you want to set, syntax 1, 5–7, available from 1 to 12 Possible value: <range>: 1 to 12 Example: Giga Switch(vlan)# disable drop-untag 5-8 disable sym-vlan...
  • Page 169 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Possible value: <range>: 1 to 12 Example: Giga Switch(vlan)# enable sym-vlan 5-8 set mode Syntax: set mode <disable|port|tag|metro|double-tag> [up-link] Description: Switches VLAN mode, including disable, port-based, tag-based, metro, and double-tag modes.
  • Page 170 CHAPTER 5: CLI Management set port-role Syntax: set port-role <range> <access|trunk|hybrid> [vid] Description: Sets Egress rule: configures the port roles. Argument: <range> :which port(s) you want to set, syntax 1, 5–7, available from 1 to 12 <access>: Do not tag frames <trunk>: Tag all frames <hybrid>: Tag all frames except a specific VID <vid>: untag-vid for hybrid port...
  • Page 171 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports set tag-group Syntax: set tag-group <vid> <name> <range> <#> Description: Adds or edits the tag-based vlan group. Argument: <vid>: vlan ID, range from 1 to 4094 <name>: tag-vlan name <range>: vlan group members, syntax 1, 5–7, available from 1 to 12...
  • Page 172 CHAPTER 5: CLI Management show pvid Syntax: show pvid Description: Displays pvid, Ingress/Egress rule. Argument: None Possible value: None Example: Giga Switch(vlan)# show pvid Port PVID Rule1 Rule2 Port Rule Untag Vid ------ ------ ------- ------- ----------- --------------- Disable Disable Access Disable Disable...
  • Page 173 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports Example: Giga Switch(vs)# enable set gid Syntax: set gid <gid> Description: Sets the group id. Argument: <gid>:Group ID Possible value: <gid>:a–z, A–Z, 0–9 Example: Giga Switch(vs)# set gid group1 set role Syntax: set role <master|slave>...
  • Page 174 CHAPTER 5: CLI Management Example: Giga Switch(vs)# show Virtual Stack Config: State : Enable Role : Master Group ID : group1...

  • Page 175: Troubleshooting

    12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports 6. Troubleshooting 6.1 Resolving a No Link Condition The possible causes for a No Link LED status are as follows: • The attached device is not powered on.

  • Page 176: Calling Black Box

    • any particular application that, when used, appears to create the problem or make it worse. 6.4 Shipping and Packaging If you need to transport or ship your 12-Port 1000BASE-TX L2 Managed PoE Switch with 2 SFP Dual Media Ports: •...

Table of Contents