6) Install the springs into the s u s p e n
sion housings, a n d place the entire
assembly onto the appropriate s u s p e n
sion height adjustment s t e m observing
the color c o d e previously mentioned.
NOTE: Align the marks on the spring
supports such that they face the centre
spindle of the turntable.
7) Level the base b y adjusting the
height of the feet, m o u n t e d o n threaded
shafts. (Only rough leveling is required
at this time: precise leveling occurs after
the turntable is m o v e d to its final posi
tion.)
8) Install the s u b c h a s s i s onto the sus
pension towers, using extreme care.
9) Retrieve the platter from the polysty
rene packaging and install it on the spin
dle.
NOTE: The platter hole and the spin
dle are tapered. Extreme care should
be taken during installation,
sure that there is no dirt on either sur
faces.
The belt must not be installed yet.
Installing the Control Unit
1) Locate the control unit in the packag
ing. C o n n e c t the A C input line into a
convenient wall outlet.
Plug the 7-pin DIN connector c o m i n g
from the motor-base a s s e m b l y into the
control unit.
2) N o w set the turntable aside s o y o u
can use the w o r k surface to prepare the
tonearm.
Cartridge Installation
1) S e l e c t the right s c r e w s for mounting
your cartridge. R e m e m b e r that steel
s c r e w s are two-and-a-half
w e i g h t of a l u m i n u m s c r e w s , a n d any
unnecessary increase in m a s s here will
have an adverse effect of warp-riding.
27 Before installing the cartridge, make
sure that the stylus protector is firmly in
place. Tighten the s c r e w s just enough
so that the cartridge can still be m o v e d .
W h e n the use of a nut is required, w e
r e c o m m e n d mounting from the top of
the head shell. Cartridge alignment will
be c o m p l e t e d after the tonearm has
been installed.
NOTE: We do not recommend the use
of any putty or damping
between the cartridge and head shell,
or the use of nylon spacers and screws
since these materials will not allow a
firm enough coupling.
Place the turntable back onto the work
surface. Y o u are n o w ready to install the
tonearm.
Tonearm Installation
T h e tonearm base a n d the subchassis
are accurately marked to facilitate their
installation.
1) S e t the F I N A L E on the subchassis
and align the marks carefully.
making
12
2) Locate the tonearm mounting plate
and s c r e w s in the s e c o n d layer of pack
a g i n g , and mount t h e m o n the subchas
sis.
Tighten the screws gradually.
3) T h e R C C o m p e n s a t i o n B o x m a y be
placed o n any convenient surface or o n
the acrylic base. T h e connecting wires
are too compliant to interfere with the
s u s p e n s i o n . A printed circuit board is
h o u s e d in the box w h i c h can be remov
ed for the soldering of resistors a n d
capacitors w h i c h
d e p e n d i n g upon your choice of cart
ridge.
NOTE:
The assistance of a qualified
technician may be required to achieve
RC compensation. Consult your deal
er.
times the
4) T o remove the P C board, remove the
s c r e w holding the b o x together a n d
gently slide the circuit out of the alumi
n u m housing.
5) T o reassemble, simply reverse the
procedure.
Cartridge Alignment
NOTE: Make sure that you use the
section
of
"FINALE".
compound
1) Place the G r o o v e Isolator mat o n the
platter.
2) Locate the C A L I B R A T O R disc in the
packaging a n d set it o n the platter.
3) R e m o v e the stylus protector and set
the tracking force within the range re
c o m m e n d e d b y the cartridge manufac
turer.
NOTE: Refer to the instruction
tracking force adjustment on page 13.
4) S e t the tonearm d o w n s u c h that the
tip of the stylus rests precisely in the
identation in the center of the adjust
ment grid.
5) Turn the V T A knob until the arm
tube is parallel to the d i s c .
NOTE: Refer to the instructions
VTA adjustment on page 13.
6) M o v e the cartridge forward or back
w a r d in the head shell s u c h that the
sides of the head shell are lined up with
the grid w h e n v i e w e d from a b o v e .
M a k e sure that the cartridge b o d y is
also parallel to the grid (and therefore
parallel with the head shell).
NOTE: Extreme care should be taken
during all stages of this procedure to
prevent damage to the delicate stylus.
m a y b e desireable
the
protractor
marked
for
for