Victor WV35 Operating Instructions Manual

OPERATING INSTRUCTIONS WV35 / WV35N
WV35
1) Attach Hose Assembly and Squeegee Floor Tool/Crevice Tool.
> Screw end of hose assembly firmly into the intake radius.
> Attach the Extension Tubes together.
> Attach one end of the Extension Tubes to the free end of the Hose Assembly
> Push the free end of the Extension Tubes into the Floor Tool.
DRY VACUUM OPTION
This model can be converted to a dry vacuum cleaner with the insertion of the Tool
Kit for Dry Use part number AYK1008. The kit consists of a Dry filter and Filter Bag
(Which is inserted into the main tank) and a selection of Floor Tools.
WV35N
1) Attach Hose Assembly and Squeegee Assembly.
> Screw end of hose assembly firmly into the intake radius.
> Push other end of hose onto the intake hole of the Squeegee Assembly .
> Lock the Squeegee Assembly into position on the Squeegee Foot pedal
assembly by locking the slotted forks under the 2 knobs located on the top of
the Squeegee Assembley.
> The Squeegee height can be set by rotating the adjusting knob at the rear of
the Squeegee Assembly.
WANDERING HOSE KIT OPTION
This model can be fitted with a Wandering Hose and Wand as per the WV35 model
part number AYK1009. The kit consists of a Hose, Steel Wand, Crevice Nozzle and
Squeegee Tool.
WV / WV35N
2) Handle Assembly
> Lift the handle so that its fixing holes line up with the fixing holes in the main tank.
> Screw the Handle Adjustment Knob through the fixing holes.
3) Operate the machine.
> Plug the machine into an appropriate power supply outlet.
> Move On/Off switch to the on position.
> Push or pull the machine over the area that is to be vacuumed.
WV / WV35N (Cont'd)
4) Empty the Full Main Tank.
> A change in the motor sound will be heard when the 35 litre Main Tank is full.
> When this is heard, switch off machine and remove plug from outlet socket.
> The machine can be emptied by releasing the liquid through the drainage hose
or by removing the power head.
OPERATING INSTRUCTIONS D9 / WD30 / WD60
D9 / WD30 / WD60
Instructions for DRY cleaning
Before using, release the clips for holding on the vacuum head. Lift out and make
sure the cloth filter is in position. Replace the head and clips.
1) Attach Hose Assembly and Floor Tool/Crevice Tool.
> Insert grooved end of hose into the canister inlet by pushing until you hear it click.
> Attach the Extension Tubes together.
> Attach one end of the Extension Tubes to the free end of the Hose Assembly
> Push the free end of the Extension Tubes into the required Tool.
IMPORTANT:
When DRY cleaning never use the machine without the cloth filter in position. Keep
the cloth filter clear by regular emptying of the canister and shaking the filter cloth. A
clogged filter reduces the air flow and the efficiency is impaired, causing the motor
temperature to rise.
Instructions for WET pick-up (WD30 / WD60 Models Only)
Before using, release the clips for holding on the vacuum head. Lift out and make
sure the CLOTH FILTER IS REMOVED. Ensure that the float moves freely in its
guides.
WD30 / WD60 (Cont'd)
The float will rise when the level of the water reaches 20L (WD30) / 55L (WD60)
and will cut off the air flow. The float will not return until the vacuum is switched
off and the canister of water is emptied. Replace the head and clips.
1) Attach Hose Assembly and Squeegee Floor Tool.
> Insert grooved end of hose into the canister inlet by pushing until you hear it
click.
> Attach the Extension Tubes together.
> Attach one end of the Extension Tubes to the free end of the Hose Assembly
> Push the free end of the Extension Tubes into the Squeegee Floor Tool.
IMPORTANT:
Leaving the tank in a dirty condition after use for wet pick-up not only causes bad
smells but could with the right ingredients, generate an inflammable gas.
Only deposit soiled water or solution into safe , suitable approved locations.
SAFETY INFORMATION (All Models)
> This machine should only be used by trained operators.
> Do not use this machine unless it is in a safe condition.
> Check the cable & plug for damage before use, and if necessary, replace
with VICTOR approved cable from our agents or direct.
> Always work within the cable length to avoid cable stress or damage.
> Check the voltage shown on the serial number plate is suitable for supply
available.
> All VICTOR Machines have maximum A-Weighted sound pressure level
measured in dB(A) is less than 85dB(A).
> The maximum r.m.s. acceleration value of any VICTOR Machine which
operators arms are subjected to =1.5m/s².
> The materials used to manufacture this machine are susceptible to damage
from petroleum based liquids. Therefore using this machine to pick up this
type of liquid will invalidate the warranty.
For an exploded parts listing for this
machine visit our website:
www.victorfloorcare.com
© Dowding & Plummer Ltd. Issue level 5, Aug 2013