Table of Contents
Advertisement
[81] Miscellaneous Alarm Reporting Codes
[81] Miscellaneous Alarm Reporting Codes
(PC1575/1580 panel only)
(PC1575/1580 panel only)
Program 2 digit reporting codes for the following:
Program 2 digit reporting codes for the following:
• General Zone Fault Alarm
• General Zone Fault Alarm
This code will be sent when the LINKS2450 receives a General Zone Fault
This code will be sent when the LINKS2450 receives a General Zone Fault
Alarm event from the PC1575/1580.
Alarm event from the PC1575/1580.
• General System Tamper Alarm
• General System Tamper Alarm
This code will be sent when the LINKS2450 receives a General System
This code will be sent when the LINKS2450 receives a General System
Tamper Alarm event from the PC1575/1580.
Tamper Alarm event from the PC1575/1580.
• General System Supervisory Alarm
• General System Supervisory Alarm
This code will be sent when the LINKS2450 receives a General System
This code will be sent when the LINKS2450 receives a General System
Supervisory Alarm event from the PC1575/1580.
Supervisory Alarm event from the PC1575/1580.
[82] Miscellaneous Restoral Reporting Codes
[82] Miscellaneous Restoral Reporting Codes
(PC1575/1580 panel only)
(PC1575/1580 panel only)
Program 2 digit reporting codes for the following (see your PC1575/1580 Installa-
Program 2 digit reporting codes for the following (see your PC1575/1580 Installa-
tion Manual for more information):
tion Manual for more information):
• General Zone Fault Restoral: This code will be sent when the LINKS2450
• General Zone Fault Restoral: This code will be sent when the LINKS2450
receives a General Zone Fault Restoral event from the PC1575/1580.
receives a General Zone Fault Restoral event from the PC1575/1580.
• General System Tamper Restoral: This code will be sent when the
• General System Tamper Restoral: This code will be sent when the
LINKS2450 receives a General System Tamper Restoral event from the
LINKS2450 receives a General System Tamper Restoral event from the
PC1575/1580.
PC1575/1580.
• General System Supervisory Restoral: This code will be sent when the
• General System Supervisory Restoral: This code will be sent when the
LINKS2450 receives a General System Supervisory Restoral event from the
LINKS2450 receives a General System Supervisory Restoral event from the
PC1575/1580.
PC1575/1580.
NOTE: Sections [81] and [82] apply to the PC1575/1580 only. All other panels will
NOTE: Sections [81] and [82] apply to the PC1575/1580 only. All other panels will
use the reporting codes that are programmed for these events in the panel.
use the reporting codes that are programmed for these events in the panel.
[83] Miscellaneous Alarm Reporting Codes
[83] Miscellaneous Alarm Reporting Codes
(PC1555/1565 v2.0 panel only)
(PC1555/1565 v2.0 panel only)
Program 2 digit reporting codes for the following (see your PC1555/1565 Installa-
Program 2 digit reporting codes for the following (see your PC1555/1565 Installa-
tion Manual for more information):
tion Manual for more information):
• Police Code: This code will be sent when the LINKS2450 receives a Police
• Police Code: This code will be sent when the LINKS2450 receives a Police
Code event from the PC1555/1565.
Code event from the PC1555/1565.
• Delinquency Code: This code will be sent when the LINKS2450 receives a
• Delinquency Code: This code will be sent when the LINKS2450 receives a
Delinquency event from the PC1555/1565.
Delinquency event from the PC1555/1565.
12
12
2.4 Mount and Wire the LINKS2450
2.4 Mount and Wire the LINKS2450
1. Run the panel wiring and the power supply wiring to the LINKS2450
1. Run the panel wiring and the power supply wiring to the LINKS2450
mounting location.
mounting location.
2. Remove the four screws that attach the LINKS2450 circuit board to the
2. Remove the four screws that attach the LINKS2450 circuit board to the
plastic cabinet.
plastic cabinet.
3. Pull all wires through the hole at the back of the cabinet.
3. Pull all wires through the hole at the back of the cabinet.
4. Mount the cabinet securely to the wall. Use the appropriate wall anchors
4. Mount the cabinet securely to the wall. Use the appropriate wall anchors
when securing the panel to drywall, plaster, concrete, brick or similar
when securing the panel to drywall, plaster, concrete, brick or similar
surfaces.
surfaces.
5. Reattach the LINKS2450 into the mounted cabinet using the four mounting
5. Reattach the LINKS2450 into the mounted cabinet using the four mounting
screws.
screws.
6. Find the antenna connection in the hole at the top of the cabinet. Secure the
6. Find the antenna connection in the hole at the top of the cabinet. Secure the
antenna to the LINKS2450 antenna connector.
antenna to the LINKS2450 antenna connector.
NOTE: Make sure an antenna is always connected to the LINKS2450 whenever it
NOTE: Make sure an antenna is always connected to the LINKS2450 whenever it
is operated. The unit will not work and may be damaged if an antenna is not in-
is operated. The unit will not work and may be damaged if an antenna is not in-
stalled.
stalled.
7. Complete all wiring: If you will be connecting the LINKS2450 to a PC5015,
7. Complete all wiring: If you will be connecting the LINKS2450 to a PC5015,
PC5010, PC1575/1580, PC1555/1565 or PC580/585 panel, go to step 7a. If
PC5010, PC1575/1580, PC1555/1565 or PC580/585 panel, go to step 7a. If
you will be connecting the LINKS2450 to a PC4010 or PC4020 panel, go to
you will be connecting the LINKS2450 to a PC4010 or PC4020 panel, go to
step 7b.
step 7b.
7a. Connect the LINKS2450 according to diagram 2-1. Make sure jumper J3
7a. Connect the LINKS2450 according to diagram 2-1. Make sure jumper J3
on the LINKS2450 is NOT shorted.
on the LINKS2450 is NOT shorted.
7b. Connect the LINKS2450 to a PC2550RK keypad according to diagram 3-
7b. Connect the LINKS2450 to a PC2550RK keypad according to diagram 3-
1. Make sure jumper J3 on the LINKS2450 IS SHORTED. When you have
1. Make sure jumper J3 on the LINKS2450 IS SHORTED. When you have
finished programming, disconnect the power supply and the PC2550RK
finished programming, disconnect the power supply and the PC2550RK
keypad from the LINKS2450. Remove the short from jumper J3 . Connect
keypad from the LINKS2450. Remove the short from jumper J3 . Connect
the LINKS2450 to the control panel according to diagram 2-2.
the LINKS2450 to the control panel according to diagram 2-2.
NOTE: Check all wiring to ensure that it is correct. Incorrect wiring connections
NOTE: Check all wiring to ensure that it is correct. Incorrect wiring connections
may cause the LINKS2450 to operate improperly, or may damage the unit.
may cause the LINKS2450 to operate improperly, or may damage the unit.
8. Connect the power: Connect the power terminals (VTX
8. Connect the power: Connect the power terminals (VTX
14V
14V
, 1A power supply.
, 1A power supply.
DC
DC
CAUTION: Do not connect the power supply until all other wiring, including the
CAUTION: Do not connect the power supply until all other wiring, including the
antenna connection, has been completed and checked to ensure that it is correct.
antenna connection, has been completed and checked to ensure that it is correct.
+
+
and VTX
and VTX
–
–
) to a 11.5 -
) to a 11.5 -
5
5
Advertisement
Table of Contents
