Advertisement
Quick Links
(ver.1.4 2011/8)
Read this instructions manual carefully before use
Minoura Japan Headquarters
(for all customers)
1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Phone: +81-584-27-3131 / Fax: +81-584-27-7505
Email: minoura@minoura.jp / www.minoura.jp
Indoor Bicycle Trainer – instructions manual
Tire Size Capacity Range <w/o Z-adaptor>
Made in Japan
B60-D
B60-R
<with Z-adaptor>
(Shown image: non-remote B60-D)
Minoura North American Tech Center
(for U.S. residents only)
Phone: 1-510-538-8599 / Fax: 1-510-538-5899
Email: support@minourausa.com
(Non-Remote)
(Remote)
26 x 1.0 – 700 x 45c
22 x 1-3/8 – 700 x 32c
Advertisement
Related Manuals for MINOURA B60-D
Summary of Contents for MINOURA B60-D
- Page 1 Tire Size Capacity Range <w/o Z-adaptor> 26 x 1.0 – 700 x 45c <with Z-adaptor> 22 x 1-3/8 – 700 x 32c (Shown image: non-remote B60-D) Read this instructions manual carefully before use Minoura Japan Headquarters Minoura North American Tech Center (for all customers) (for U.S.
-
Page 2: Important Notice
Tire-to-roller contact will eventually wear both your tire and the trainer roller. It's normal. • On B60-D (non-remote type), adjusting the resistance must be done when the bike stopped. Do not operate the Dial Lever (EM-13) for changing the resistance power while the rear wheel is spinning. - Page 3 MF-3: Micro Adjust Knob Set BF-5 BF-6 BF-5 <B60-R Remote> BF-6 EM-1 M5-2 EM-2 MF-3 EM-4 EM-3 EM-5 EM-6 EM-17 EM-8 <B60-D Non-Remote> EM-1 EM-2 EM-9 EM-3 EM-4 EM-10 EM-13 EM-5 EM-8 EM-11 LM-10 EM-12 EM-17 EM-1: Outer Cap EM-10: Cable Guide...
- Page 4 Replace your rear wheel quick release skewer to the supplied one. Minoura guarantees the stability only when using the supplied skewer due to the coupling inner shape. If your bike is not equipped with quick release skewer and it's a hub nut type, you should remove the black plastic Grommet (Skewer Nut Protector) (F-9) from the right side coupling.
- Page 5 Place your rear wheel in between the couplings. 1) Turn the Hub Handle in the direction of counter-clockwise to make the enough space Coupling between the couplings. You should almost fully open the coupling for easier wheel installation. (see Fig. C) Be careful not to over-loosen the Hub Handle.
- Page 6 Contact the Drive Roller to the rear tire by turning the Roller Pressure Adjust Knob clockwise. (see Fig. G) The best position is that the roller compresses the tire in the depth of 3 - 4 mm. (see Fig. H) Please note too much and too less roller pressure will bring premature tire wear.
- Page 7 How To Adjust Resistance Level (B60-D) B60-D provides 3 different resistance levels to suit your training level. To Increase Resistance Level: Slide the Dial Lever toward "H" position. To Decrease Resistance Level: Slide the Dial Lever toward "L" position. (Fig. L)
- Page 8 Why My Remote Shifter Doesn't Work Properly? You may have a shifting problem that you cannot set at L or H position properly due to the lengthened inner cable. To fix this problem, follow the steps to adjust the initial cable tension.