Belkin Conserve Switch User Manual

Now you can control power to your
circuit breaker
whole computer system or AV-system
reset switch
0 1
with a single click. The wireless
protected
remote switch lets you shut off
indicator light
channelselector
power—including standby power—to up
(back of surge
to six devices at once. Two Always-On
protector)
Sockets stay on for devices that need
continuous power, like your router or
two (2)
always on
cordless phone. Place the remote on always on
indicator light
sockets
a desk or shelf, or mount it on the wall,
for the convenient way to save energy.
For more information and to learn
manual override
about other Belkin Conserve energy
switch and
management products, please
indicator light
go to belkin.com/conserve six (6)
remote
switched
sockets
Package Contents
2 meter power
8-Socket Conserve Switch Surge Protector
cord
Wireless Remote Switch (battery included)
Remote Switch Wall-Mount
User Guide and Warranty Information
cable management
8820uk00555_F7C01008_ConserveSwitch_harmonica_uk.indd 1
QUICK SETUP GUIDE 2
Plug in any of your devices that require
1
constant, round-the-clock power into
Plug in any of your devices that do not
one of the Conserve Switch Surge
require constant, round-the-clock power
detachable wireless Protector's Always-On Sockets.
into one of the Conserve Switch Surge
remote switch with
Protector's Remote-Switched Sockets.
wall-mount
on
off
Channel Select 0 1
front back
channel
selector
A23 (12V)
battery
3 INDICATOR LIGHTS HOW TO USE YOUR CONSERVE
Plug your Conserve Switch's
power cord into a wall socket.
The "Always-On Sockets" light should be REMOTE SWITCH
on if power is present. If this light goes out
1
at any time, it means the circuit breaker Firmly press and release the "I" button to
has tripped and should be reset. turn ON the Remote-Switched Sockets.
As you press the button, a green light
The "Remote-Switched Sockets"
flashes on the remote switch to indicate
light shows the state of the Remote-
that the remote is working. Your devices
Switched Sockets. When the light is
are now powered and ready for use.
on, the Remote-Switched Sockets are
powered; if the light is off, the Remote-
Switched Sockets are not powered.
4
Remove the clear battery tab from
the back of the remote switch. The
remote is now ready to use.
NOTE: Mounting screws are not included;
see the "Wireless Remote Switch with
Wall-Mount" section later in this user guide.
2 5 SYNCING INSTRUCTIONS
Turn on and use your devices as usual. When ready to use your equipment
again, repeat Steps 1–5.
On the bottom left corner of the back of the
3 NOTE: A green LED on the wireless Surge Protector, there is a similar set of
When you are finished using your devices,
remote switch will illuminate when the switches. The switch settings on both the
turn off each device as you normally would.
switch is pressed. This indicates that the
remote and Surge Protector must match
signal was sent and that the battery is in order for the remote to communicate
4 OK. If you do not see the light, it is time with the Surge Protector. You can use a
When your devices are turned off, firmly
to replace the battery. To replace the
press and release the "O" button to turn
battery, see the Troubleshooting section.
OFF the Remote-Switched Sockets. As
you press the button, a green light flashes
Not Matching/Not Synced
on the remote switch to indicate that
you have eliminated power to Conserve SYNCING INSTRUCTIONS 0 1 0 1
Switch's Remote-Switched Sockets.
Devices plugged into the Always- On Syncing your Conserve Switch Surge
Remote Surge Protector
Sockets will remain powered.
Protector and Wireless Remote Switch
By default your Conserve Switch Surge Matching/Synced
Protector and remote should be synced when
0 1 0 1
purchased. However, if you need to change
the sync settings for any reason, you can do
Remote Surge Protector
this by locating and changing the channel
setting switches on the back of the remote
small screwdriver to shift the switches.
and on the back of the Surge Protector. On the
By adjusting these channel setting switches,
back of the remote, under the battery cover,
you can control multiple Conserve Switch
there is a series of three switches that can be
Surge Protectors with a single remote
set to up to eight diff erent confi gurations.
switch. Adjust the channel setting on each
Conserve Surge Protector to match the
setting on a single remote switch. This will
enable you to easily turn off the power to
multiple devices connected to multiple
surge protector units within range.*
09/06/2010 09:31:50