Related Manuals for Keys Fitness Cable Gym KPS-CG
Summary of Contents for Keys Fitness Cable Gym KPS-CG
- Page 1 KPS-CG ABLE Questions? Call our toll free Keys Fitness Helpline 1 - 8 0 0 - 6 8 3 - 1 2 3 6...
-
Page 2: Registration Card
This manual will guide you through the assembly process. If at any time you are having trouble with the assembly or use of this product, then please contact us at our Keys Fitness Helpline. We have trained service technicians on site to take care of you, our valued customer. -
Page 3: Before You Start
• This Power System unit should only be used on a level surface and is intended for indoor use only. Keys Fitness recommends an equipment mat be placed under the unit to protect the floor or carpet and for easier cleaning. - Page 4 STEP 1 Slide weight guide rods into main base and secure with: 2 x (90) Allen Bolt Tighten allen bolts in guide rods before proceding. Attach left and right side base (6,7) to main base (1) using: 2 x (84) Bolt ASSEMBLY 2 x (101) Spring Washer 4 x (98) Washer...
- Page 5 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 2 Slide the following down onto the guide rods: 2 x (64) Weight Bumper 9 x (30) 10 lb plate 1 x (28) Top Plate ASSEMBLY 5 x (29) 15 lb plate 5 x (31) 5 lb plate...
- Page 6 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 3 Attach the upright to the main base using: 2 x (83) Bolt Slide top frame onto upright and weight guide rods and secure using: 2 x (81) Bolt 2 x (85) Bolt ASSEMBLY 4 x (98) Washer...
- Page 7 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 4 Complete assembly on right and left slide frames (10,11) using: 2 x (13) Swivel Pulley Block 2 x (101) Spring Washer Position right and left slide frames (10,11) on right and left guide rods (4,5) then attach to frame using: 2 x (86) Bolt 2 x (82) Bolt...
- Page 8 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 5 Connect seat frame (16) to main base and upright (1,2) using: 2 x (85) Bolt 2 x (84) Bolt ASSEMBLY 4 x (98) Washer 4 x (98) Washer 2 x (96) Nylon Locknut 2 x (96) Nylon Locknut...
- Page 9 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 6 Attach leg extension (18) to seat frame (16) using: 1 x (22) LE Pivot 2 x (97) Nylon Locknut Attach foam frames (34,35) to leg extension (18) using: 1 x (94) Split Pin 2 x (51) Bushing 2 x (70) Semi-Ball End Cap...
- Page 10 STEP 7 Attach seat pad (53) to seat support (17) using: 2 x (106) Allen Bolt Slide into seat frame and adjust to desired level. Attach back pad (52) to back pad rotative support (9) using: 2 x (79) Bolt Connect back pad rotative support (9) to back pad slide support (8) using: 1 x (88) Bolt Slide into upright frame and adjust to desired level.
- Page 11 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 8 Attach right and left roller frame (14,15) to upright frame (2) using: 2 x (84) Bolt Attach foot plate (19) to main base (1) using: 1 x (23) Long L Pin 4 x (98) Washer 2 x (96) Nylon Lock Nut...
- Page 12 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 9 Complete roller pad (25) assembly using: 1 x (55) Long Foam Tube 6 x (63) Mushroom Plug ASSEMBLY 2 x (65) Big Plastic Washer 6 x (25) Roller Pad 1 x (92) Screw...
- Page 13 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 10 Complete weight cable (37) assembly as shown using: 7 x (40) Big Pulley 1 x (86) Bolt 2 x (50) Pulley Spacer ASSEMBLY 2 x (54) Big Cable Retainer 14 x (98) Washer 1 x (105) Floating Pulley Block 6 x (79) Bolt...
- Page 14 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 11 Complete middle cable (38) assembly as shown using: 1 x (40) Big Pulley 1 x (79) Bolt 2 x (71) Bolt 2 x (78) Bolt 2 x (39) Gear Hook ASSEMBLY 2 x (73) Wide Pulley 2 x (27) Double Bracket Pulley Block 2 x (98) Washer...
- Page 15 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 12 Complete lat cable (36) assembly on left side of machine as shown using: 3 x (40) Big Puley 1 x (54) Big Cable Retainer 1 x (78) Bolt 2 x (79) Bolt 1 x (82) Bolt 1 x (89) Bolt...
- Page 16 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 13 Complete lat cable (36) assembly on right side of machine as shown using: 3 x (40) Big Puley 1 x (54) Big Cable Retainer 1 x (78) Bolt 2 x (79) Bolt 1 x (82) Bolt 1 x (89) Bolt...
- Page 17 ASSEMBLY STEP 14 Connect necessary attachments as shown for needed exercises. TIGHTEN ALL BOLTS AND NUTS BEFORE PROCEEDING.
- Page 18 ASSEMBLY STEP 15 Connect shrouds (68) to main frame using: 4 x (91) Allen Bolt 4 x (99) Washer...
- Page 19 ASSEMBLY You have now completed the assembly of your new Cable Gym. Included with your unit is a workout placard which shows all of the basic exercises that can be performed on the Cable Gym. This workout placard can be placed securely on either side of the weight stack shrouds for easy viewing during workouts.
-
Page 20: Parts List
Description main base upright top frame right guide rod left guide rod right side base left side base back pad slide support back pad rotative support right slide frame left slide frame weight guide rod swivel pulley block right roller frame left roller frame seat frame seat support... -
Page 21: Exploded View
EXPLODED VIEW... - Page 22 Product. To obtain warranty service, you must contact a Keys authorized retailer, service technician or Keys Fitness at our phone number located in this manual. Any parts determined to be defective must be returned to Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product.
- Page 24 Keys Fitness Products, L.P. 4009 Distribution Drive, Suite 250 Garland, Texas 75041 Customer Service: 1-800-683-1236...