Alarm Mode - Casio 2839 Operation Manual

Alarm Mode

You watch comes with five alarms and an hourly time signal.
• Daily Alarms (AL 1 to AL 4)
The watch beeps for about 10 seconds when an alarm time is
reached.
• Snooze Alarm (SNZ)
With the snooze alarm, the watch beeps for 10 seconds when the
alarm time is reached, and up to seven times at five-minute
intervals thereafter (approximately 30 minutes total). Pressing any
button stops the beeper, but the alarm will sound again after five
minutes.
• Hourly Time Signal
The hourly time signal causes the watch to beep twice every hour
on the hour.
When you enter the Alarm Mode, the screen for the alarm that was
displayed when you last exited the mode appears first.
Timekeeping Mode
Current Time
Alarm Number
(Three Times)
Alarm Time
5.
Use the D D D D D (+) and B B B B B (–)
buttons to change the
minute setting.
• Each press of the B (+) and
D (–) button changes the
minute setting in 30-minute
(Forward)
increments.
• Holding down either button
changes the setting at high
speed.
6.
When the setting is the
way you want, press the
A button. A A A A
• This exits the setting screen.
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
Operation Guide 2839
❚ To select an alarm or the Hourly Time
Signal screen
Each press of the D button cycles through available screens in
the sequence shown below.
Alarm 1
Hourly Time Signal
Snooze Alarm
❚ To turn an alarm or the hourly time
(Back)
signal on and off
1. Alarm number
In the Alarm Mode, use the
D D D D D button to display the
screen for the alarm you
want to turn on or off.
• The alarm number or snooze
alarm indicator (SNZ) appears
at the bottom of the display to
indicate the current screen.
2.
Press the B B button to toggle the displayed alarm on or off. B B B
Alarm Hourly Time Signal
Alarm On indicator Hourly Time Signal On Indicator
Snooze Alarm
Snooze On Indicator
❚ To set an alarm time
Example: To set Alarm 2 for 3:30 p.m.
1.
In the Alarm Mode, use the
D button to scroll through D D D D
the alarm screens until the
one whose setting you want
to change is displayed.
Alarm 2
• The alarm number or snooze
alarm indicator (SNZ) appears
at the bottom of the display to
indicate the current screen.
2.
Hold down the A A button A A A
for about two seconds
until the hour digits start
to flash on the display.
Alarm 3
• This also causes the alarm on
indicator to appear and
automatically turns on the alarm.
A A A A A Button
• Enters/exits the setting mode.
B B B B B Button
• Scrolls back through the options at the flashing (selected)
Alarm 4
setting.
C C C Button C C
• Moves the flashing between settings.
D D D D Button D
• Scrolls forward through the options at the flashing
(selected) setting.
❚ To stop the alarm beeper
Press any button.
• In the case of the snooze alarm the alarm will sound again in
about five minutes. "SNZ" flashes while the snooze alarm is active
(indicating that the alarm will sound again).
• The snooze alarm will be canceled automatically when any of the
following occurs while the Snooze alarm indicator (SNZ) is
flashing on the display.
• If you turn off the snooze alarm in the Alarm Mode.
• If you enter the Alarm Mode, display the snooze alarm screen,
and then display the setting screen.
• If you enter the Timekeeping Mode and then display the setting
screen.
❚ To test the alarm
In the Alarm Mode, hold down the B button to sound the alarm.
3.
Use the D D D D D (+) and B
buttons to change the
hour setting.
Alarm Number
• Holding down either button
changes the setting at high
speed.
• When setting the hour, make
sure you specify AM (A) or
PM (P) correctly when using
12-hour timekeeping, or that
you specify the correct
24-hour time.
• The same 12-hour/24-hour
format you select for the
Hour Timekeeping Mode time is
also applied in the Alarm
Mode.
4.
C C C button to
Press the C C
select the minute setting.
Alarm on indicator
(Back)
B (–) B B B
(Forward)
Minute
7