• The product-specific section includes service, reference, and product-specific parts information. Important: This manual is intended only for trained servicers who are familiar with Lenovo products. Use this manual to troubleshoot problems effectively. Before servicing a Lenovo product, make sure to read all the information under...
Safety information Safety information This chapter presents the following safety information that you need to get familiar with before you service a Lenovo MIIX 3-1030 computer: • “General safety” on page 2 • “Electrical safety” on page 3 • “Safety inspection guide” on page 5 •...
MIIX 3-1030 Hardware Maintenance Manual General safety Follow these rules below to ensure general safety: • Observe a good housekeeping in the area where the machines are put during and after the maintenance. • When lifting any heavy object: 1. Make sure that you can stand safely without slipping.
Safety information Electrical safety Observe the following rules when working on electrical equipments. Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents.
Page 8
MIIX 3-1030 Hardware Maintenance Manual • Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. • Do not touch live electrical circuits with the reflective surface of a plastic dental mirror.
4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
MIIX 3-1030 Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.
Safety information Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer.
Page 12
MIIX 3-1030 Hardware Maintenance Manual Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short- circuit it. Dispose of the battery as required by local ordinances or regulations.
Safety information Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
Page 14
MIIX 3-1030 Hardware Maintenance Manual Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations.
Page 15
Safety information Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau d’affichage à...
Page 16
MIIX 3-1030 Hardware Maintenance Manual Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation.
Page 17
Safety information Safety notice 8 DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
MIIX 3-1030 Hardware Maintenance Manual Laser compliance statement Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S.
Page 19
Safety information A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.
To download software fixes, drivers, and BIOS, follow the steps below: 1. Go to http://support.lenovo.com. 2. Enter a serial number or select a product or use Lenovo smart downloading. 3. Select the BIOS/Driver/Applications and download. 4. Follow the directions on the screen and install the necessary software.
Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: • If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue. •...
FRU part numbers. Lenovo plans to transit to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo’s requirements and schedule in the EU. Products sold in 2005 and 2006 will contain some RoHS compliant FRUs.
General checkout General checkout This chapter presents the following information: • “What to do first” on page 20 • “Power system checkout” on page 21 Before you go to the checkout, make sure to read the following important notes: Important notes: • Only certified trained personnel can service the computer.
MIIX 3-1030 Hardware Maintenance Manual What to do first When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2.
4. If the voltage is acceptable, do the following: • Replace the system board. • If the problem continues, go to “Lenovo MIIX 3-1030” on page 26. Note: Noise from the AC adapter does not always indicate a defect. Checking operational charging...
Page 26
MIIX 3-1030 Hardware Maintenance Manual Perform operational charging. If the battery status indicator or icon does not light on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack.
In order to save application files and the initial backed-up files of the system, the hard disk in a Lenovo computer includes a hidden partition when it is shipped. If you need to restore the system to the point of your first boot up, just enter the Recovery System (Push-button reset).
MIIX 3-1030 Hardware Maintenance Manual Passwords As many as two passwords may be needed for any Lenovo computer: the power-on password (POP) and the supervisor password (SVP). If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on.
Related service information Power management Note: Power management modes are not supported for APM operating system. To reduce power consumption, the computer has two power management modes: screen blank, sleep (standby). Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off.
• “FRU replacement notices” on page 28 • “Removing and replacing an FRU” on page 29 • “Locations” on page 49 • “Parts list” on page 51 Specifications The following table lists the specifications of the Lenovo MIIX 3-1030: Table 1. Specifications Feature Description Processor •...
Lenovo MIIX 3-1030 Function key combinations (located on the folio case) The following table shows the function of each combination of function key. Table 2. Fn key combinations (located on the folio case) Fn + Esc : Mutes/unmutes the sound.
This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the Lenovo computer, this problem is addressed with special nylon-coated screws that have the following characteristics: •...
Lenovo MIIX 3-1030 Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules: 1. Do not attempt to service any computer unless you have been trained and certified.
MIIX 3-1030 Hardware Maintenance Manual 1010 LCD cover Figure 1. Removal step of LCD cover Firstly, the suction cup* to stick under the camera's position, use your hand pull the suction cup. Then insert prying tool* between the logo "Lenovo" and the camera, slide it around.
Page 35
Lenovo MIIX 3-1030 Figure 1. Removal step of LCD cover (continued) When installing: 1. To install the LCD cover, align the connector hole of the LCD cover with the connector on the panel module. 2. Hold the tablet and press the two part together in the direction shown by arrows until you hear a slight click.
Page 36
MIIX 3-1030 Hardware Maintenance Manual Note: Applying labels to the LCD cover The new LCD cover FRU is shipped with a kit containing labels of several kinds. When you replace the LCD cover, you need to apply the following labels: The following labels need to be peeled off from the old LCD cover, and put on the new LCD cover.
Lenovo MIIX 3-1030 1020 Battery pack For access, remove this FRU: • “1010 LCD cover” on page 30 DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode. Figure 2. Removal steps of battery pack Disconnect the battery connector in the direction shown by arrow 1, then remove the screws 2.
Page 38
MIIX 3-1030 Hardware Maintenance Manual Figure 2. Removal steps of battery pack (continued) Remove the battery pack in the direction shown by arrow 4. When installing: • Make sure the connector is attached firmly. • Route the cables along the cable guides. As you route the cables, make sure that they are not subjected to any tension.
Lenovo MIIX 3-1030 1030 Docking transfer board For access, remove these FRUs in order: • “1010 LCD cover” on page 30 • “1020 Battery pack” on page 33 Figure 3. Removal steps of docking transfer board Detach the connector in the direction shown by arrow...
MIIX 3-1030 Hardware Maintenance Manual 1040 Power board For access, remove these FRUs in order: • “1010 LCD cover” on page 30 • “1020 Battery pack” on page 33 Figure 4. Removal steps of power board Detach the power board connector in the directions shown by arrows...
Lenovo MIIX 3-1030 1050 Microphone module For access, remove these FRUs in order: • “1010 LCD cover” on page 30 • “1020 Battery pack” on page 33 Figure 5. Removal steps of microphone module Detach the microphone connector in the direction shown by arrow .
MIIX 3-1030 Hardware Maintenance Manual 1060 Antenna assembly For access, remove these FRUs in order: • “1010 LCD cover” on page 30 • “1020 Battery pack” on page 33 Figure 6. Removal steps of antenna assembly Disconnect the two wireless LAN cables (black, white)
Lenovo MIIX 3-1030 1070 Front camera For access, remove these FRUs in order: • “1010 LCD cover” on page 30 • “1020 Battery pack” on page 33 • “1050 Microphone module” on page 37 • “1060 Antenna assembly” on page 38 Figure 7.
MIIX 3-1030 Hardware Maintenance Manual 1080 Speaker For access, remove these FRUs in order: • “1010 LCD cover” on page 30 • “1020 Battery pack” on page 33 Figure 8. Removal steps of speaker Detach the speaker connector in the direction shown by arrow...
Lenovo MIIX 3-1030 1090 System board Important notices for handling the system board: When handling the system board, bear the following in mind. • Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
Page 46
MIIX 3-1030 Hardware Maintenance Manual Figure 9. Removal steps of system board (continued) Remove the system board as shown by arrow...
Lenovo MIIX 3-1030 1100 Keyboard dock back cover (on select models) Figure 10. Removal steps of keyboard dock back cover (on select models) Pry up both ends of the rubber strip in the direction shown by arrows Open the two rubber feet in the direction shown by arrows Note: The two rubber feet are connected to the dock back cover (see illustration below, marked in the red).
Page 48
MIIX 3-1030 Hardware Maintenance Manual Figure 10. Removal steps of keyboard dock back cover (on select models) (continued) To separate the back cover and the upper case: 1. Insert a prying tool between the back cover and the dock upper case on the lower-right corner of the keyboard dock.
Page 49
Lenovo MIIX 3-1030 Figure 10. Removal steps of keyboard dock back cover (on select models) (continued) Gently detach the two connectors in the direction shown by arrows , then remove the dock upper case Peel off the two pieces of tape that secure the two USB boards in the direction...
Page 50
MIIX 3-1030 Hardware Maintenance Manual Figure 10. Removal steps of keyboard dock back cover (on select models) (continued) Remove the two USB boards...
Lenovo MIIX 3-1030 1110 Docking board (on select models) For access, remove this FRU: • “1100 Keyboard dock back cover (on select models)” on page 43 Figure 11. Removal steps of docking board (on select models) Remove the screws Step...
MIIX 3-1030 Hardware Maintenance Manual 1120 Touchpad (on select models) For access, remove these FRUs in order: • “1100 Keyboard dock back cover (on select models)” on page 43 • “1110 Docking board (on select models)” on page 47 Figure 12. Removal steps of touchpad (on select models)
Lenovo MIIX 3-1030 Locations Tablet front view Front camera Built-in microphone Power button Volume up button Volume down button Multi-touch screen Tablet rear view Speaker Micro SD card slot Micro HDMI port Micro USB port Combo audio jack Keyboard dock/Folio case connector...
MIIX 3-1030 Hardware Maintenance Manual Keyboard dock (on select models) Keyboard dock connector USB 2.0 port Touchpad Folio case (on select models) Folio case connector Keyboard Touchpad...
Lenovo MIIX 3-1030 Parts list This section presents the following service parts: • “Overall” on page 52 • “Screws” on page 56 • “AC adapters” on page 56 • “Power cords” on page 56 • “Folio case (on select models)” on page 57...
Page 57
Lenovo MIIX 3-1030 Table 3. Parts list—Overall (Tablet) (continued) FRU no. CRU ID. FFC Cable B MIIX3-1030 White 5C10H00063 LCD Module B MIIX3-1030 FHD 5D10G99942 LCD Module B MIIX3-1030 HD 5D10G99934 LCD Module B MIIX3-1030 FHD G1 5D10H11016 MB B MIIX3-1030 W8P Z3735 2G32G...
Page 58
MIIX 3-1030 Hardware Maintenance Manual Keyboard dock (on select models)
Page 59
Lenovo MIIX 3-1030 Table 4. Parts list—Overall (Keyboard dock (on select models)) (continued) FRU no. CRU ID. Upper Case B MIIX3-1030 W/KB US 5CB0H20075 Upper Case B MIIX3-1030 W/KB UK 5CB0H20092 Upper Case B MIIX3-1030 W/KB IT 5CB0H20073 Upper Case B MIIX3-1030 W/KB SP...
The result obtained in other operating environments may vary. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.
Notices Trademarks The following terms are either registered trademarks or trademarks of Lenovo in the United States and/or other countries: ® Lenovo ® Lenovo logo The following terms are trademarks of Microsoft Corporation in the United States, other countries, or both: ®...