Kenwood KAC-7203 Instruction Manual

Kenwood KAC-7203 Instruction Manual

Stereo bridgeable power amplifier
Table of Contents

Advertisement

Available languages

Available languages

KAC-7203
STEREO/BRIDGEABLE POWER AMPLIFIER 7 page 2-7
INSTRUCTION MANUAL
AMPLIFICATEUR DE PUISSANCE STEREO/COMPATIBLE 7 page 8-13
MODE D'EMPLOI
ESTÉREO/AMPLIFICADOR DE POTENCIA CONECTABLE 7 página 14-19
MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual. Familiarity
with installation and operation procedures will help you obtain the
best performance from your new power amplifier.
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below. Refer
to the model and serial numbers whenever you call upon your Kenwood
dealer for information or service on the product.
Model KAC-7203 Serial number
US Residence Only
Register your Kenwood product at
www.kenwoodusa.com
© B64-3501-00/00 (KV/EV)
Register Online

Advertisement

Table of Contents
loading

Summary of Contents for Kenwood KAC-7203

  • Page 1 Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
  • Page 2: Safety Precautions

    NOTE • If you experience problems during installation, consult your Kenwood dealer. • If the unit does not seem to be working right, consult your Kenwood dealer. FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.
  • Page 3: Installation Procedure

    Installation 380 mm 320 mm Ø6 Hexagon socket head cap screw Dressing cover (M4 × 8 mm) Cooling fan Self-tapping screw (ø5 × 18 mm) Accessories Self-tapping screws (ø5 × 18 mm) Terminal cover (Power or speaker terminal) Speaker level input cable Hexagon Wrench Installation procedure Since there are large variety of settings and connections possible according to...
  • Page 4 Connection 2WARNING To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the battery’s positive terminal. 2CAUTION • If sound is not output normally, immediately turn power off and check connections. • Be sure to turn the power off before changing the setting of any switch.
  • Page 5: Power Indicator

    (See page 3) 1 Fuse (40 A × 1) NOTE If you can’t find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF.
  • Page 6: System Examples

    System examples ■ 2-channel system CENTER UNIT ■ 2-channel + Subwoofer system CENTER UNIT LINE OUT LINE OUT ■ Tri-mode (High pass) CENTER UNIT English ■ High-power 2-channel subwoofer system Left speaker Right speaker Left speaker (High pass) Right speaker (High pass) Subwoofer (L + R) (Bridged)
  • Page 7: Troubleshooting Guide

    Troubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM POSSIBLE CAUSE No sound. • Input (or output) cables are disconnected. (No sound from one side.) •...
  • Page 8: Précautions De Sécurité

    (comme une pièce de monnaie ou un outil en métal) à l'intérieur de l'appareil. • Si l'appareil commence à émettre de la fumée ou une odeur bizarre, mettez immédiatement l'appareil hors tension et consultez un revendeur Kenwood. • Ne pas toucher l’appareil quand il est en service car la température de sa surface est suffisamment élevée pour provoquer des brûlures.
  • Page 9: Procédure D'installation

    Installation 380 mm 320 mm Ø6 Vis d’assemblage à six pans creux Enjoliveur (M4 × 8 mm) Ventilateur de refroidissement Vis taraudeuse (ø 5 × 18 mm) Accessoires Vis taraudeuses (ø5 × 18 mm) Cache de bornier (Borne d’alimentation ou d’enceinte) Câble d'entrée de niveau d'enceinte Clé...
  • Page 10 Raccordements 2AVERTISSEMENT Pour éviter tout incendie dû à un court- circuit, insérer un fusible ou un coupecircuit à proximité de la borne de la batterie. 2ATTENTION • En cas d'anomalie, mettre immédiatement l'appareil hors tension et vérifier tous les raccordements. •...
  • Page 11 1 FUSIBLE (40 A × 1) REMARQUE Si vous ne trouvez pas de fusible de calibre adéquat dans le commerce, etc., contacter votre agent Kenwood. 2 Borne BATT (alimentation) 3 Borne GND (masse) 4 Borne P.CON (fil de commande d’alimentation) Commande l’unité...
  • Page 12: Exemple De Configuration

    Exemple de configuration ■ Système 2 voies Unité centrale ■ Système 2 voies + enceinte d'extrêmes graves Unité centrale LINE OUT LINE OUT ■ Le Tri-mode (filtre passe- haut) Unité centrale Frençais ■ Système de subwoofer à 2 canaux haute puissance Haut-parleur gauche Haut-parleur droit Haut-parleur gauche (filtre passe-haut)
  • Page 13: Guide De Depannage

    Guide de depannage Ce qui peut apparaître comme un mauvais fonctionnement de votre appareil n’est peut être que le résultat d’une mauvaise opération ou d’une mauvaise connexion. Avant d’appeler un centre de service, vérifiez d’abord dans le tableau suivant les problèmes possibles. PROBLEME CAUSE POSSIBLE Absence de sons.
  • Page 14: Precauciones De Seguridad

    • Si nota que la unidad emite humos u olores extraños, desconecte inmediatamente la alimentación y consulte con su distribuidor Kenwood. • No toque el aparato mientras lo utiliza porque su superficie se calienta y puede causar quemaduras si se toca.
  • Page 15: Procedimiento De Instalación

    Instalación 380 mm 320 mm Ø6 Tornillo de cabeza hexagonal Cubierta exterior (M4 × 8 mm) Ventilador de refrigeración Tornillo autorroscantes (ø5 × 18 mm) Accesorios Tornillo autorroscantes (ø5 × 18 mm) Cubierta de terminales (Terminal de altavoz o de potencia) Cable de entrada del nivel de altavoces Llave hexagonal...
  • Page 16 Conexiones 2ADVERTENCIA Para evitar incendios producidos por cortocircuitos en el cableado, conecte un fusible o cortacircuito entre la batería y los terminales de la batería. 2PRECAUCIÓN • Si el sonido no sale normalmente, desconecte inmediatamente la alimentación y compruebe las conexiones. •...
  • Page 17 1 FUSIBLE (40 A × 1) NOTA Si no puede encontrar el fusible de la capacidad especificada en su almacén etc., consulte su distribuidor Kenwood. 2 Terminal BATT (alimentación) 3 Terminal GND (tierra) 4 Terminal del control de corriente (P.CON) Controla la CONEXIÓN / DESCONEXIÓN de la...
  • Page 18 Ejemplos del sistema ■ Sistema de 2 canales APARATO CENTRAL ■ Sistema de 2 canales + Altavoz de subgraves APARATO CENTRAL LINE OUT LINE OUT ■ Tri-modo (Paso alto) APARATO CENTRAL Español ■ Sistema subwoofer de 2 canales de alta potencia Altavoz izquierdo Altavoz derecho Altavoz izquierdo (Paso alto)
  • Page 19: Guia Sobre Localización De Averias

    Guia Sobre Localización De Averias Lo que podría parecer una falla de funcionamiento de su unidad podría ser simplemente el resultado de un pequeño error de operación o de un defecto de conexión. Antes de acudir al servicio, verifique primero el siguiente cuadro sobre los problemas que se podrían presentar. PROBLEMA CAUSA POSIBLE No hay sonido.

Table of Contents