Safety Check-Out; Unleaded Solder - Sony HDR-PJ260 Service Manual

Ver. 1.2 2012.05
The changed portions from
Ver. 1.1 are shown in blue.
Model information table
Model HDR-PJ260 HDR-PJ260E
Destination KR NE, E, CH, JE
COLOR system NTSC PAL
Internal memory Internal memory
Recording media
16 GB 16 GB
LENS LSV-1450A LSV-1450A
Projector ● ●
GPS ─ ─
Hot shoe ─ ─
Charging capacitor
─ ─
(for flash)
MODEL GROUP
• Abbreviation
AUS: Australian model
BR: Brazilian model
CH: Chinese model
CND: Canadian model
HK: Hong Kong model
JE: Tourist model
KR: Korea model
NE: North European model
HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2
HDR-PJ260V HDR-PJ260VE HDR-XR260E HDR-XR260V HDR-XR260VE
AEP,UK,NE, E,
US, CND, E E, CH US, CND, E, BR
AUS
NTSC PAL PAL NTSC
Hard Disk Hard Disk
Internal memory Internal memory
Drive Drive
16 GB 16 GB
160 GB 160 GB
LSV-1450A LSV-1450A LSV-1450A LSV-1450A
● ● ─ ─
● ● ─ ●
─ ─ ─ ─
─ ─ ─ ─
AEP,UK,NE, E,
AUS, HK
PAL
Hard Disk
Drive
160 GB
LSV-1450A
─
●
─
─
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are "pinched"
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Set the soldering iron tip temperature to 350 °C approximately.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
– 3 –
ATTENTION AU COMPOSANT AYANT RAPPORT
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.

UNLEADED SOLDER

This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
À LA SÉCURITÉ!