1 Introduction This booklet describes the programmable parameters, and provides bar codes for programming the Pocket Memo dictation recorder with barcode scanner. Operational Parameters The Pocket Memo dictation recorder with barcode scanner is shipped with the factory default settings shown in the table below. These factory default values are stored in non-volatile memory and are preserved even when the scanner is powered down.
Page 6
Parameter Parameter no (Hex) Factory default Code 32 Prefix Disable Set Length(s) for Code 39 2-55 Code 39 Check Digit Verification Disable Transmit Code 39 Check Digit Disable Code 39 Full ASCII Conversion Disable Code 93 Code 93 Disable Set Length(s) for Code 93 4-55 Code 11 Code 11...
Set Default Parameter 2 Set default parameter Scan Set Factory Defaults to restore the factory default values listed in Table 4-1 on page 4-2. Scan Set Factory Defaults to restore the factory default values listed in the table on page 5. Set Factory Defaults LED On Time Parameter # 88h...
UPC/EAN UPC/EAN Enable/Disable UPC-A 3 UPC/EAN Enable/Disable UPC-A Parameter # 01h Parameter # 01h To enable or disable UPC-A, scan the appropriate bar code below. Enable/Disable UPC-A To enable or disable UPC-A, scan the appropriate bar code below. Parameter # 01h To enable or disable UPC-A, scan the appropriate bar code below.
Parameter # 0Ch To enable or disable UPC-E1, scan the appropriate bar code below. To enable or disable UPC-E1, scan the appropriate bar code below. Enable/Disable UPC-E1 UPC-E1 is not a UCC (Uniform Code Council) approved symbology. NOTE Parameter # 0Ch UPC-E1 is not a UCC (Uniform Code Council) approved symbology.
Parameter # 03h Enable/Disable EAN-13 Parameter # 03h To enable or disable EAN-13, scan the appropriate bar code below. Enable/Disable EAN-13 Parameter # 03h To enable or disable EAN-13, scan the appropriate bar code below. To enable or disable EAN-13, scan the appropriate bar code below *Enable EAN-13 (01h) *Enable EAN-13...
Parameter # F1h 40h If Bookland EAN is enabled, select one of the following formats for Bookland data: Bookland ISBN Format • Parameter # F1h 40h Bookland ISBN-10 - The digital scanner reports Bookland data starting with 978 in traditional 10-digit format with the If Bookland EAN is enabled, select one of the following formats for Bookland data: special Bookland check digit for backward-compatibility.
Page 12
Decode UPC/EAN Supplementals (continued) Select the desired option by scanning one of the following bar codes. Select the desired option by scanning one of the following bar codes. Decode UPC/EAN With Supplementals (01h) *Ignore UPC/EAN With Supplementals (00h) Autodiscriminate UPC/EAN Supplementals (02h) Enable 378/379 Supplemental Mode (04h)
Parameter # F1h A0h Select an output format when reporting UPC/EAN/JAN bar codes with Supplementals with Transmit Code ID Character on page 4-67 set to AIM Code ID Character UPC/EAN/JAN Supplemental AIM ID Format • - transmit UPC/EAN with supplementals with separate AIM IDs but one transmission, i.e.: Separate Parameter # F1h A0h Select an output format when reporting UPC/EAN/JAN bar codes with Supplementals with Transmit Code ID Character set to AIM Code ID...
Transmit UPC-E Check Digit Parameter # 29h Transmit UPC-E Check Digit Scan the appropriate bar code below to transmit the symbol with or without the UPC-E check digit. Parameter # 29h Scan the appropriate bar code below to transmit the symbol with or without the UPC-E check digit. *Transmit UPC-E Check Digit (01h) 4 - 22 SE655 Decoded Linear Imaging Engine...
Page 16
(00h) UPC-A Preamble UPC-A Preamble Parameter # 22h Parameter # 22h Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A symbol. Select one of the following options for Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A symbol. Select one of transmitting UPC-A preamble to the host device: transmit system character only, transmit system character and country code (“0”...
UPC-E Preamble Parameter # 23h UPC-E Preamble Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E symbol. Select one of Parameter # 23h the following options for transmitting UPC-E preamble to the host device: transmit system character only, transmit system Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E symbol.
UPC-E1 Preamble Parameter # 24h UPC-E1 Preamble Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E1 symbol. Select one of Parameter # 24h the following options for transmitting UPC-E1 preamble to the host device: transmit system character only, transmit system Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E1 symbol.
Convert UPC-E1 to UPC-A Parameter # 26h Convert UPC-E1 to UPC-A Enable this parameter to convert UPC-E1 (zero suppressed) decoded data to UPC-A format before transmission. After Parameter # 26h conversion, data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit). Enable this parameter to convert UPC-E1 (zero suppressed) decoded data to UPC-A format before transmission.
UPC/EAN Security Level UPC/EAN Security Level UPC/EAN Security Level UPC/EAN Security Level Parameter # 4Dh UPC/EAN Security Level Parameter # 4Dh Parameter # 4Dh Parameter # 4Dh Parameter # 4Dh The SE655 offers four levels of decode security for UPC/EAN bar codes. Increasing levels of security are provided for The SE655 offers four levels of decode security for UPC/EAN bar codes.
UCC Coupon Extended Code Parameter # 55h UCC Coupon Extended Code The UCC Coupon Extended Code is an additional bar code adjacent to a UCC Coupon Code. To enable or disable UCC Parameter # 55h Coupon Extended Code, scan the appropriate bar code below. The UCC Coupon Extended Code is an additional bar code adjacent to a UCC Coupon Code.
Parameter # F1h DAh Traditional coupon symbols (old coupon symbols) are composed of two bar codes: UPC/EAN and Code128. A new coupon Coupon Report symbol is composed of a single Databar Expanded bar code. The new coupon format offers more options for purchase Parameter # F1h DAh values (up to $999.99) and supports complex discount offers such as a second purchase requirement.
Set Lengths for Code 128 Parameter # L1 = D1h L2 = D2h The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Code 128 to any length, one or two discrete lengths, or lengths within a specific range. NOTE: When setting lengths for different bar code types, enter a leading zero for single digit numbers.
Parameter # 0Eh Enable/Disable GS1-128 (formerly UCC/EAN-128) To enable or disable GS1-128, scan the appropriate bar code below. (See Appendix A, Miscellaneous Code Information Parameter # 0Eh details on GS1-128 (formerly UCC/EAN-128).) Enable/Disable GS1-128 (formerly UCC/EAN-128) To enable or disable GS1-128, scan the appropriate bar code below. (See Appendix A, Miscellaneous Code Information Parameter # 0Eh details on...
Select an option for concatenating pairs of ISBT code types: • If you select Disable ISBT Concatenation, the digital scanner does not concatenate pairs of ISBT codes it ISBT Concatenation encounters. Parameter # F1h 41h • If you select Enable ISBT Concatenation, there must be two ISBT codes in order for the digital scanner to decode Select an option for concatenating pairs of ISBT code types: and perform concatenation.
Page 28
Parameter # DFh If you set ISBT Concatenation to Autodiscriminate, use this parameter to set the number of times the digital scanner ISBT Concatenation Redundancy must decode an ISBT symbol before determining that there is no additional symbol. Parameter # DFh Scan the bar code below, then scan two numeric bar codes in Numeric Bar Codes on page 4-73 to set a value between 2...
Convert Code 39 to Code 32 (Italian Pharma Code) Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar code below to enable Parameter # 56h or disable converting Code 39 to Code 32. Convert Code 39 to Code 32 (Italian Pharma Code) Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry.
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for Code 39 may be set for any length, one or two discrete lengths, or lengths within a specific range. If Parameter # L1 = 12h L2 = 13h The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code Parameter # L1 = 12h L2 = 13h...
with specified check digit algorithm. Only those Code 39 symbols which include a modulo 43 check digit are decoded. Only Parameter # 30h Code 39 Check Digit Verification enable this feature if your Code 39 symbols contain a module 43 check digit. When this feature is enabled, the scan engine checks the integrity of all Code 39 symbols to verify that the data complies Parameter # 30h Code 39 Check Digit Verification...
Enable/Disable Code 39 Full ASCII Parameter # 11h Enable/Disable Code 39 Full ASCII Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set. To enable or Parameter # 11h disable Code 39 Full ASCII, scan the appropriate bar code below. Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set.
Set Lengths for Code 93 Parameter # L1 = 1Ah L2 = 1Bh Set Lengths for Code 93 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code Parameter # L1 = 1Ah L2 = 1Bh contains.
Page 36
Code 11 7 Code 11 Enable/Disable Code 11 Parameter # 0Ah Enable/Disable Code 11 To enable or disable Code 11, scan the appropriate bar code below. Parameter # 0Ah To enable or disable Code 11, scan the appropriate bar code below. Enable Code 11 (01h) Disable Code 11...
Set Lengths for Code 11 Parameter # L1 = 1Ch L2 = 1Dh The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Code 11 to any length, one or two discrete lengths, or lengths within a specific range. •...
Code 11 Check Digit Verification Code 11 Check Digit Verification Parameter # 34h Parameter # 34h This feature allows the scan engine to check the integrity of all Code 11 symbols to verify that the data complies with the This feature allows the scan engine to check the integrity of all Code 11 symbols to verify that the data complies with the specified check digit specified check digit algorithm.
Parameter # 06h Interleaved 2 of 5 To enable or disable Interleaved 2 of 5, scan the appropriate bar code below. 8 Interleaved 2 of 5 Enable/Disable Interleaved 2 of 5 Parameter # 06h Enable/Disable Interleaved 2 of 5 To enable or disable Interleaved 2 of 5, scan the appropriate bar code below. Parameter # 06h To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.
digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the Length Within Range - Select this option to decode only codes within a specified range. For example, to decode I 2 of 5 selection or cancel an incorrect entry, scan Cancel on page 4-74.
Transmit I 2 of 5 Check Digit Transmit I 2 of 5 Check Digit Parameter # 2Ch Transmit I 2 of 5 Check Digit Parameter # 2Ch Scan this symbol to transmit the check digit with the data. Parameter # 2Ch Scan this symbol to transmit the check digit with the data.
Discrete 2 of 5 Enable/Disable Discrete 2 of 5 Discrete 2 of 5 Enable/Disable Discrete 2 of 5 Parameter # 05h 9 Discrete 2 of 5 Enable/Disable Discrete 2 of 5 Parameter # 05h To enable or disable Discrete 2 of 5, scan the appropriate bar code below. Parameter # 05h To enable or disable Discrete 2 of 5, scan the appropriate bar code below.
Page 43
Selecting this option may lead to misdecodes for D 2 of 5 codes. NOTE NOTE: Selecting this option may lead to misdecodes for D 2 of 5 codes. D 2 of 5 - Any Length Barcode scanner configuration guide...
Chinese 2 of 5 10 Chinese 2 of 5 Enable/Disable Chinese 2 of 5 Parameter # F0h 98h Enable/Disable Chinese 2 of 5 To enable or disable Chinese 2 of 5, scan the appropriate bar code below. Parameter # F0h 98h To enable or disable Chinese 2 of 5, scan the appropriate bar code below.
Matrix 2 of 5 11 Matrix 2 of 5 Enable/Disable Matrix 2 of 5 Parameter # F1h 6Ah Enable/Disable Matrix 2 of 5 To enable or disable Matrix 2 of 5, scan the appropriate bar code below. Parameter # F1h 6Ah To enable or disable Matrix 2 of 5, scan the appropriate bar code below.
Set Lengths for Matrix 2 of 5 Parameter # L1 = F1h 6Bh L2 = F1h 6Ch The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Matrix 2 of 5 to any length, one or two discrete lengths, or lengths within a specific range.
edundancy Matrix 2 of 5 Redundancy 1h 6Dh Parameter # F1h 6Dh Matrix 2 of 5 Redundancy atrix 2 of 5 redundancy, scan the appropriate bar code below. To enable or disable Matrix 2 of 5 redundancy, scan the appropriate bar code below. Parameter # F1h 6Dh To enable or disable Matrix 2 of 5 redundancy, scan the appropriate bar code below.
Enable/Disable Codabar Codabar Parameter # 07h 13 Codabar Enable/Disable Codabar To enable or disable Codabar, scan the appropriate bar code below. Parameter # 07h Enable/Disable Codabar To enable or disable Codabar, scan the appropriate bar code below. Parameter # 07h To enable or disable Codabar, scan the appropriate bar code below.
Any Length - Scan this option to decode Codabar symbols containing any number of characters. 4 - 60 SE655 Decoded Linear Imaging Engine 4 - 60 SE655 Decoded Linear Imaging Engine CLSI Editing Parameter # 36h CLSI Editing Codabar - Any Length When enabled, this parameter strips the start and stop characters and inserts a space after the first, fifth, and tenth Parameter # 36h characters of a 14-character Codabar symbol.
14 MSI Enable/Disable MSI Parameter # 0Bh Enable/Disable MSI To enable or disable MSI, scan the appropriate bar code below. Parameter # 0Bh To enable or disable MSI, scan the appropriate bar code below. Enable MSI (01h) 4 - 62 SE655 Decoded Linear Imaging Engine 4 - 62 SE655 Decoded Linear Imaging Engine *Disable MSI Set Lengths for MSI...
Selecting this option may lead to misdecodes for MSI codes. NOTE MSI Check Digits Parameter Menus 4 - 63 NOTE: Selecting this option may lead to misdecodes for MSI codes. MSI Check Digits Parameter # 32h Parameter Menus 4 - 63 Parameter # 32h These check digits at the end of the bar code verify the integrity of the data.
Page 53
Parameter # 33h When the Two MSI check digits option is selected, an additional verification is required to ensure integrity. Select one of the MSI Check Digit Algorithm following algorithms. Parameter # 33h When the Two MSI check digits option is selected, an additional verification is required to ensure integrity. Select one of the following algorithms. MOD 10/ MOD 11 (00h) *MOD 10/ MOD 10...
Enable/Disable GS1 DataBar Expanded Parameter # F0h 54h Parameter # F0h 54h To enable or disable GS1 DataBar Expanded, scan the appropriate bar code below. Enable/Disable GS1 DataBar Expanded To enable or disable GS1 DataBar Expanded, scan the appropriate bar code below. Parameter # F0h 54h To enable or disable GS1 DataBar Expanded, scan the appropriate bar code below.
Numeric Bar Codes 16 Numeric Bar Codes For parameters requiring specific numeric values, scan the appropriately numbered bar code(s). For parameters requiring specific numeric values, scan the appropriately numbered bar code(s). Barcode scanner configuration guide...
Numeric Bar Codes (continued) Cancel Cancel To change the selection or cancel an incorrect entry, scan the bar code below. Cancel To change the selection or cancel an incorrect entry, scan the bar code below. To change the selection or cancel an incorrect entry, scan the bar code below. Cancel Cancel Barcode scanner configuration guide...