Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Proxima Tsunami MP.11
- Page 1 Part Number 69141 Tsunami MP.11 and MP.11a Version 2.2 Quick Install Guide...
-
Page 2: Fcc Compliance
FCC COMPLIANCE This document provides regulatory information for the following wireless outdoor products: ▪ Tsunami MP.11 2411 BSU, Tsunami MP.11 2411 SU, Tsunami MP.11 2411 RSU ▪ Tsunami 2411 QuickBridge 11 ▪ Tsunami MP.11a BSU, Tsunami MP.11a SU, Tsunami MP.11a RSU This device complies with Part 15 of the FCC Rules. -
Page 3: Key Features
The Tsunami MP.11 and MP.11a product families comprise several products (such as the Tsunami MP.11 SU and BSU). For simplification, all products that are part of the Tsunami MP.11 and MP.11a Product Families are referred to as MP.11/MP.11a. - Page 4 Wall mounting hardware Power supply with power cord The shipment also includes the Tsunami MP.11/MP.11a Quick Install Guide. 2. If you intend to install the unit free-standing, or if you intend to mount it to the ceiling, use a Phillips screwdriver to attach the metal base to the underside of the unit.
- Page 5 MP.11 and MP.11a Quick Install Guide 3. Unlock the unit’s cable cover. To release the cable cover, press down on the cable cover lock located in the front center of the unit. 4. Remove the cable cover. 5. Remove the front cover from the unit (the side with the LED indicators, shown in the figure on left); then remove the back cover (figure on right).
- Page 6 MP.11 and MP.11a Quick Install Guide 8. If you are not using Active Ethernet, or you want to connect the MP.11/MP.11a to Active Ethernet and AC power simultaneously, attach the AC power cable to the unit’s power port. To disconnect the power cable, slide back the black plastic fitting around the connector and gently pull the connector from the MP.11/MP.11a unit.
- Page 7 MP.11 and MP.11a Quick Install Guide Mounting the Unit The following are the mounting options for the MP.11/MP.11a: ▪ Desktop Mount ▪ Wall Mount ▪ Ceiling Mount Desktop Mounting This procedure consists of attaching the metal base to the MP.11/MP.11a unit. See “Installation Procedure” on page 4.
- Page 8 MP.11 and MP.11a Quick Install Guide 7. Place the back cover on the mounting location and mark the center of the three mounting holes. 8. Remove the cover from the wall and drill a hole at each of the locations you marked. Each hole should be wide enough to hold a mounting plug (6 mm x 35 mm).
- Page 9 MP.11 and MP.11a Quick Install Guide Switching On the Unit The MP.11/MP.11a can be powered by a power supply (just plug the power cord of the power supply into an AC power outlet), or by Active Ethernet (connect an Active Ethernet splitter to the Ethernet cabling). When the power is switched on, the MP.11/MP.11a performs startup diagnostics.
-
Page 10: Installing Documentation And Software
This is the help for the Web Interface. It is stored on your computer or network so it is always available. Documentation Documentation also is available in an electronic (PDF) form, including the Tsunami MP.11 and MP.11a Installation and Management Guide, Tsunami MP.11 Antenna Installation Guide, and this Quick Install Guide. -
Page 11: Accessing The Web Browser
2. A login window is displayed. Do not fill in the User name; enter only the default password public. If your MP.11/MP.11a is configured to obtain an IP address dynamically: 1. Install ScanTool, located on the Tsunami MP.11/MP.11a CD-ROM. The MP.11/MP.11a must be on the same subnet as the PC on which ScanTool is installed; if necessary, change the PC’s IP settings. - Page 12 It scans the available frequencies and channels to avoid radar and select a channel with the strongest signal. By default, the Tsunami MP.11/MP.11a lets you transmit at the maximum output power for the country or regulatory domain and frequency selected. However, with Transmit Power Control (TPC), you can adjust the...
-
Page 13: Changing The Security Settings
The MP.11/MP.11a is equipped with embedded software. Updates of this software can be found on the Proxim Internet site. Not all software releases support all products in the Tsunami MP.11/MP.11a family. Proxim recommends that you always refer to the Release Notes to determine whether the version of software to which you want to upgrade is supported on your MP.11/MP.11a product. - Page 14 MP.11 and MP.11a Quick Install Guide Support and Contacts If you are having a problem using a Proxim WAN product and cannot resolve it with the information in the product documentation, gather the following information and contact Proxim Technical Support: ▪...