Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nagel 2S Trimmer
Summary of Contents for Nagel 2S Trimmer
- Page 1 2S Trimmer User Manual Nagel 2S Trimmer...
- Page 2 PAGE INTENTIONALLY BLANK © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010...
-
Page 3: Table Of Contents
6.1 G ..............................21 ENERAL 6.2 C ..........................21 LEANING THE BELTS TECHNICAL INFORMATION ........................23 DECLARATION OF CONFORMITY ....................... 24 HISTORY................................. 25 NOTES ................................26 WIRING DIAGRAMS............................27 © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 4: Safety
10 meters of the concerning machines. RoHS The 2-Side Trimmer is RoHS compliant. ONLY use RoHS compliant replacement parts ordered from NAGEL. compliant © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. -
Page 5: General
The main goal of the 2-Side Trimmer, further referred to as 2S Trimmer or 2S Tr, is that it can be used for trimming the bleed off the booklet. Booklets with a maximum up to 25 sheets 80g/m2 (50 folded) can be trimmed from 2mm to 35mm on each short edge of the booklet, to a minimum of 200mm and a maximum of 320mm finished size. -
Page 6: Basic Information 2S Trimmer
User Interface (UI) Belt Stacker This manual applies to the 2S TRIMMER. Due to the mirroring, typical Front and Rear designations which normally is viewed from the operator location has been replaced by Left and Right. Left and Right is viewed from the paper input direction. - Page 7 Transport Belts Motor 7, Side Jogger Knives Motor 2, Knife Solenoid Trimmer Stop Motor 3, Knife Side Joggers Motor 8, Side Jogger Power Switch Motor 4, Knife Interlock Switch © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010...
-
Page 8: Operating The 2S Trimmer
4. Operating the 2S Trimmer This section explains how to use the 2S Trimmer during normal operation. From either side (top or bottom) 40mm of the finished booklet should be free from staples to ensure safe operation. NOTE: The System Setup has to be set once. -
Page 9: Language
Use the ‘▲ / ▼ buttons’ to select ‘Language:’ and press the ‘Enter’ button. (Fig. 2) Select Language Use the ‘▲ / ▼ buttons’ to select the correct Language (Fig. 3). Save and confirm with [Enter] © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 10: Job Setup
Finished Size (booklet after trimming) (A) Waste (front trim) (B) Waste (rear trim) (C) Equals: Input Size (booklet before trimming) (D) or short: A + B + C = D © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 11: Paper Size Setup
‘Enter’ button. (Fig. 2) Select ‘Standard Paper Size:’ Use the ‘▲ / ▼ buttons’ to select the correct ‘Standard Paper Size:’ (Fig. 3). Save and confirm with [Enter] © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 12: Job Setup
Job or ‘Rename’ the adjusted Job by pressing the ‘Enter’ button (Fig. 2). Attention: An “Saving Job” signal appears for a few seconds. Attention: After Rename a Job, repeat step 2A ‘Enter Job name’. © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 13: Paper Input Size Setup
4. Operating the 2S Trimmer (continued) 4.6 Paper Input Size Setup NOTE: In the “Input Size” menu of the 2S Trimmer the paper Input Size can be set or adjusted. Fig. 1 Fig. 2 Fig. 3 Step Action Remarks Input Size adjustment Use the ‘▲... -
Page 14: Side Trim On / Off
After all desired settings are adjusted press ‘Jobs’ (Fig. 4) and press ‘Enter’ (Fig. 5) to save the settings. Attention: A “Saving Job” signal appears for a few seconds. © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 15: Centre Offset
Press ‘Enter’ (Fig. 3) to confirm the settings. Save settings. After the Center Offset is adjusted press ‘Jobs’ (Fig. 1) and press ‘Enter’ (Fig. 2) to save the settings. © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 16: Purge Button
4. Operating the 2S Trimmer (continued) 4.9 Purge Button Fig.1 Step Action Remarks Press Purge Button. Use the ‘Purge buttons’ to move booklets forward onto the Belt Stacker (Fig.1). © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 17: Troubleshooting
Attention: It is possible that there is still some Waste. Cutting Waste left inside the 2S Tr. Place the Trim Waste bins back in (Fig. 3) the Trim Drawer. Close the Trim Drawer. (Fig. 2) © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 18: Clearing A Paper Jam
5.2.1 Warnings / Cautions An increasing number of Paper Jams is an indication of the need to clean the belts. The 2S Trimmer Upper knife blades are protected by a Knife Safety Plate that moves away during the Trim cycle movement. - Page 19 The booklet will move into the 2S Tr. Take the booklet out of the Push or pull the booklet inside the 2S Trimmer so it is machine. possible to take the booklet out of a machine. Turn ‘ON’ the 2S Tr.
-
Page 20: Stop If Booklet Is Too Thick
The booklet will move into the 2S Tr. Take the booklet out of the Push or pull the booklet inside the 2S Trimmer so it is machine. possible to take the booklet out of a machine. Turn ‘ON’ the 2S Tr. -
Page 21: Cleaning / Maintenance
6.2 Cleaning the belts The belts of the 2S Trimmer need to be cleaned regularly during normal conditions even if the 2S Trimmer has not been used for a while. How often this should be done depends on the paper type and print quality. - Page 22 Turn ‘ON’ the S2S Tr. A signal ‘Cover Open’ will appear. Close the Top Cover. The Knife blocks will automatically move to each other to set ready for current Job. © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010...
-
Page 23: Technical Information
340 mm must be Booklets Height (Z) 204 mm trimmed back to 320mm or up to 340 mm shorter. 40mm Booklet Staple Clearance from top/bottom (minimal) 70dB Noise Level (max) © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 24: Declaration Of Conformity
Year of affixing the CE marking/ L' an de l' application de la marque CE: 2010 Stuttgart, 22.Otober 2010 Ort und Datum/ Geschäftsführer/ Place and date/ Managing Director / Lieu et date Gérant © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 25: History
History Rev. 1.0 16.11.2010 © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 26: Notes
Notes © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0. 16.11.2010... -
Page 27: Wiring Diagrams
User Manual 2S Trimmer Wiring Diagrams © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0 16.11.2010... - Page 28 User Manual 2S Trimmer © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0 16.11.2010...
- Page 29 User Manual 2S Trimmer © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0 16.11.2010...
- Page 30 User Manual 2S Trimmer © Ernst Nagel GmbH 9965242 User Manual 2S Trimmer en.doc Rev.1.0 16.11.2010...