Advertisement
Disconnect the charger from the mains supply when not in use.
DO NOT charge battery if room temperature is below 41°F (5°C) or above 104°F (40°C)
DO NOT expose the charger to damp or wet conditions.
DO NOT pull or carry the charger by the power lead.
DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take the charger to an authorised agent for repair or
obtain a replacement.
DO NOT dismantle the charger as this may cause damage and/or personal injury and will invalidate the warranty.
DO NOT insert foreign objects or material into the hole reserved for the battery pack.
DO NOT recharge a second battery pack immediately after charging the first.
Consecutive charging will overheat the charger.
Allow the unit to cool for 15 minutes before charging the next pack.
Store the charger in the same manner as battery pack in paragraph 1.2.
2.
INTRODucTION & SPEcIFIcATION
one of the most powerful cordless impact wrenches
on the market. Produces torque in excess of 4150kg.
cm(300lb.ft) - enough to remove wheel nuts. Forward
and reverse controls integrated into housing for ease
of use. Suitable for workshop, body shop and tyre
shop applications. Features replaceable motor
brushes and includes 19.2Volt 2Ah Ni-Cad battery
pack and charger.
No-Load Speed . . . . . . . . . . . . . . . . . . 0-2000rpm
Impact Rate . . . . . . . . . . . . . . . . . . . . . . 2600bpm
Maximum Torque . . . . . . . . . .300ft.lb / 4150kg.cm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.0kg
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2V
Charge Time . . . . . . . . . . . . . . . . . . . . . . . . . . 1hr
Drive Size . . . . . . . . . . . . . . . . . . . . . . . . . .1/2"Sq
Battery Pack . 19.2V 2Ah (Model No. CP3003BP)
Noise Power . . . . . . . . . . . . . . . . . . . . .90.33dB.A
Noise Pressure . . . . . . . . . . . . . . . . . .101.33dB.A
3. OPERATING INSTRucTIONS
IMPORTANT WARRANTY INFORMATION:
The battery pack fitted to this cordless tool is considered to be a consumable item and its
ability to accept charge will reduce over time. We will warranty it against mechanical and
electrical defect for a period of one year - this does not cover fair wear and tear. If the
battery is not properly charged before first use, or regularly conditioned, its capacity will
diminish. Under these circumstances we will not replace the battery pack even if it is less
than one year old.
Remove battery pack from case and charge as below:
3.1.
Removing/Installing Battery Pack.
WARNING! Do not touch metal terminals.
3.1.1. To remove the battery from the wrench, grasp both sides of the battery pack and squeeze
the release buttons on each side (Fig. 2 & 2A), withdraw pack from wrench (Fig.2).
3.1.2. To insert the battery pack, align the tongue in battery pack with the groove in the wrench
housing and push into place (Fig. 2A).
WARNING! Do not use force when inserting the battery pack. If it does not slide in easily
then it is not being inserted correctly.
WARNING! Ensure you read, understand and apply safety instructions before use.
3.2.
charging Battery Pack.
Note: If you try to charge a battery pack that has just been used, the charging light may
not come on. If this occurs, let the pack cool for a while, then re-insert and try to
charge again.
If you try to charge a battery that is new or been inactive for a long period, it may
not accept a full charge. This is normal and after a couple of charges the battery
will accept a full charge.
If you wish to charge two battery packs, allow fifteen minutes between charging to
allow the charger to cool, after three consecutive charges allow one hour to cool
before further use.
3.2.1. Plug the charger into the supply.
3.2.2. Insert battery pack so that the + and - symbols on the battery line up with the + and -
symbols on the charger (battery only fits the charger in one position).
3.2.3. The red charging (fast charge) light will come on and charging will begin. If the charging
light goes out to soon, remove the battery pack and allow to cool for two minutes before
3.2.4. If the charging light goes out within a minute even after repeating this procedure a couple
battery is dead and requires replacing.
3.2.5. When the battery light switches to green (trickle charge) you may remove the fully charged battery pack.
3.2.6. After charging, unplug the charger from the power source.
Side Handle Adaptor (optional)
Variable speed switch
Forward/Reverse Button
Fig.1
Battery Pack
Original Language Version
Carbon Brush Cover
Fig. 2
Release Button
Fig. 2A
charging again.
of times, then the
CP3003.V2
Issue: 2 - 04/01/12
Charging
LEDs
Advertisement
