Program Overlap Warning Display; Other Functions; Checking Tape Position; Changing Display Information - JVC HR-S8010UM Instructions Manual

– Timer Recording –

Program overlap warning display

If "PROGRAM NOT COMPLETED PROGRAM OVERLAP"
appears, you have another program overlapping the program you
have just made. The Program Check screen appears and
conflicting programs will start blinking.
PROGRAM NOT COMPLETED
PROGRAM OVERLAP
Example:
Program 1 (you have just made) and Program 4 overlap each
other
A
Select program to modify
Press , then press .
rt e
You can only select one of the
overlapping programs.
If you do not mind this overlap, press
PROG. to finish the timer program
setting. The program starting earlier or
program with the lower program number will be recorded.
B
Cancel or change program setting
To cancel a program, press CANCEL when
the Program screen you do not want is
shown.
To change a program, press the
appropriate button: START
keys "1" and/or "4"), STOP
(Number keys "2" and/or "5"), DATE
and/or "6"), CH / and/or SP/EP when the Program screen on
which you want to make changes is shown, then press OK.
If the overlap is not yet solved, the conflicting programs will be
shown on the Program check screen. Repeat the above steps
again.
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4 9:00P 10:00 10 12/24
5
6
7
8
( , ), THEN ( ) (PROG.) : END
PR START STOP CH
1 8:00P 10:00 12
2 10:00A 10:45 40
3 11:30P 1:00 125
4 9:00P 10:00 10
5
6
7
8
( , ), THEN ( ) (PROG.) : END
PROGRAM 4
START STOP
9:00PM 10:00PM
DATE CH
12/24/03 10 SP
WED
PRESS (CANCEL) TO CANCEL
PRESS (OK) TO CONFIRM
/ (Number
PRESS (PROG.) TO END
/
/ (Number keys "3"

Other Functions

Checking tape position

When you change the VCR operation
mode from the stop mode to fast forward
or rewind mode, or when you perform an
Index Search or Instant Review, the tape
position indicator appears.
The position of "
(Beginning) or "E" (End) shows you where
you are on the tape.
Set "SUPERIMPOSE" to "ON". (

Changing display information

DATE
12/24
12/25
12/25
12/24
Each time you press DISPLAY, the display panel
shows the channel number and the clock time
alternatively.
You can change display in the stop, recording or
during picture search.
When "SUPERIMPOSE" is set to "ON"
( pg. 13) and DISPLAY on the Remote is pressed, time
counter will appear on the TV screen. To reset the time counter,
press C. RESET on the Remote.

Timer warning display

A warning appears on the TV screen to tell
you that the timer-recording is to start in
5 minutes if you are not in the timer
recording standby mode at that time. Press
TIMER to put the VCR into timer recording
standby mode. To clear the display, press
CANCEL on the Remote.

Tape Remaining Time

Press DISPLAY to display the tape remaining time on the screen.
NOTES:
Set "SUPERIMPOSE" to "ON" (
indication on the screen.
Depending on the type of tape used, the tape remaining time
may not appear right away, or is not correct. "– –:– –" may
sometimes appear, or the display may blink on occasion.
— 12 —
B
" in relation to "B"
q
pg. 13)
pg. 13) to display the
+ + + E
REMAIN 1:00
COUNT 1:23:45
–WARNING–
TIMER RECORDING
TO START SOON
(CANCEL)