Advertisement
1.3.8.DO NOT pull the plug from the socket by the cable.
1.3.9.DO NOT use worn or damage cables, plugs or connectors. Immediately have any faulty item
repaired or replaced by a qualified electrician. When an ASTA/BS approved UK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
Ensure that the double insulated charger is correctly connected via a three-pin plug, as
follows:
a)
Connect the Brown live wire to live terminal 'L'.
b) Connect the Blue neutral wire to the neutral terminal 'N'.
c)
After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends past the cable clamp and that the
clamp is tight. Note that the earth pin 'E' remains unconnected.
1.4. BATTERY CHARGER SAFETY INSTRUCTIONS
WARNING! DO NOT attempt to charge any battery other than that supplied for the wrench.
other types of batteries may explode!
All mains electrical supply safety features must be followed as described in 1.3 above.
Disconnect the charger from the mains supply when not in use.
DO NOT charge battery if room temperature is below 10°C (50°F) or above 40°C (104°F).
DO NOT expose the charger to damp or wet conditions.
DO NOT pull or carry the charger by the power lead.
DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take the charger to an authorised
agent for repair or obtain a replacement.
DO NOT dismantle the charger as this may cause damage and/or personal injury and will invalidate the warranty.
DO NOT insert foreign objects or material into the hole reserved for the battery pack.
DO NOT recharge a second battery pack immediately after charging the first. Consecutive charging will overheat the charger.
Allow the unit to cool for 15 minutes before charging the next pack.
DO NOT attempt to connect two chargers together.
Store the charger in the same manner as the battery pack in 1.2.
2.
INTRODUCTION & SPECIFICATION
Powerful cordless ratchet wrench with hardened steel anvil and twist-reverse mechanism. Finger
operated trigger incorporated in housing. Textured soft grip helps reduce vibration. Features built-in
lED work light for use in low-light areas. Suitable for workshop applications. Includes 14.4V ni-Cd
battery pack and 1 hour mains charger.
Drive: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8" Sq
Maximum Torque: . . . . . . . . . . . . . . . 35lb.ft, 48nm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9kg
Battery Pack: . . . . . ..14.4V (Model no. CP2144BP)
noise Power. . . . . . . . . . . . . . . . . . . . . . . . . 89dB.A
noise Pressure . . . . . . . . . . . . . . . . . . . . . 100dB.A
3. OPERATING INSTRUCTIONS
IMPORTANT WARRANTY INFORMATION:
The battery pack fitted to this cordless tool is considered to be a consumable
item and its ability to accept charge will reduce over time. We will warranty it
against mechanical and electrical defect for a period of one year - this does not
cover fair wear and tear. If the battery is not properly charged before first use,
or regularly conditioned, its capacity will diminish. Under these circumstances
we will not replace the battery pack even if it is less than one year old.
3.1.
CHARGING THE BATTERY PACK
3.1.1. Remove the battery pack (fig.1F) from the wrench, by depressing the two
side release clips (fig.1F).
WARNING! DO NOT touch metal terminals.
3.1.2. Place wrench in carry case and remove the battery charger.
3.1.3. The battery pack and charger positive (+) and negative (-) terminals are
marked. Align the terminals correctly and insert the battery into the slot.
Note: The battery pack is designed so that it will only enter the charger unit the correct
way. When placed in the charger, a very slight downward pressure will seat the
pack firmly into the power terminals.
3.1.4. Switch on main supply to charger and the red lED will light and the charger
will begin charging the battery.
3.1.5. When the red lED goes out and the green lED illuminates, this indicates that
charging is complete. The battery pack is now ready for use.
3.1.6. After removing the battery, disconnect the charger from the mains supply and
store it in the carry case.
note: The first charge and several subsequent charges will take longer than usual
until the battery reaches optimum performance, after that the usual charge
time will take approximately 1 hour.
© Jack Sealey limited
Original Language Version
RECOMMENDED
FUSE RATING:
5AMP
fig.1
CP2144 Issue:6(I) - 12/02/14
Advertisement
