OPERATING CONTROLS HANDSET CONTROLS Helical antenna Liquid Crystal Display (LCD) MEM button CID (Caller ID) button Press to enter the caller ID mode. Number 1 button TALK button Used for long distance dialing. Number 8 ( ) button (time button) 0-9, , # Dial buttons Used to display the date and time of the received calls.
ALIGNMENT PROCEDURE BASE UNIT / TRANSMITTER Test Equipment Required and Connections • Oscilloscope • Dummy Load, 50-ohm • Frequency Counter • AC Power Supply: 120V, 60Hz (With AC Adapter) • Digital Voltmeter Base Unit Frequency Counter Dummy Load (50-ohm) − RF Test DC IN 9V AC Adapter...
Page 5
RECEIVER Test Equipment Required and Connections • SG: RF Signal Generator, 49.830 MHz, 49.160 MHz • Dummy Load, 600-ohm • Digital Voltmeter • AF SSVM • SINAD Meter Base Unit AF SSVM Dummy Load (600-ohm) RF Test TEL Jack Point MOD = 1KHz DEV = ±3kHz Digital Voltmeter...
HANDSET / TRANSMITTER Test Equipment Required and Connections • DC Power Supply, 3.6V • Digital Voltmeter Frequency Counter Handset Unit Dummy Load (50-ohm) RF Test Point Batt Terminal DC Power Supply Digital Voltmeter TX VCO 3.6V Test Point Preset Turn Power on while depressing “ ” and “#” keys. A beep will be heard. Then the TX Mode is entered (CH21). Alignment Procedure Step Adjustment...
Page 7
RECEIVER Test Equipment Required and Connections • SG: RF Signal Generator, 46.770 MHz, 46.610 MHz • Dummy Load, 150-ohm • VTVM • DC Power Supply: 3.6 V • Digital Voltmeter • SINAD Meter Handset Unit VTVM Dummy Load (150-ohm) RF Test Point Terminal Batt Terminal...
TROUBLESHOOTING HINTS 1. The bell does not ring. When the PAGE SW of the See 2. The bell does not ring base is pressed, does the & page does not ring. ringer on the handset ring? When the TEL SG is joined By using voltage chart, with the base to make bell IC3 is defective.
Page 13
2. The bell does not ring & page does not ring. Can the base and handset By using voltage chart, Check the base TX power. be connected? check the base TX circuit. Check the base TX data Check R53, R74, R71, deviation.
Page 14
3. The base and handset cannot connect. By using voltage chart, Check whether the Check the base TX power. check the base TX circuit. handset and the base unit are connected. Check the base TX data Check R53, R74, R71, deviation.
Page 15
Then, can the sine wave Check Q2 and surrounding be seen at the Q2 Collector. circuit of Q2. Check the surrounding circuit of T1. 4. Cannot make a phone call (pulse). Can the base and handset See 3. The base and be connected? handset cannot connect.
6. Voice cannot be transmitted to other party (outgoing call). At the MIC of the handset, Check R548, R534, R532 Check the handset MIC does the bias voltage exist? and C555. sensitivity. Check the base RX In the base, with the SG Check the handset TX AF TEL-line out.
Page 17
7. The voice of the caller cannot be heard (incoming call). In the handset, with the SG Check the handset IF Check the handset RX SP standard modulation of circuit (around Pins 26~29 out. 1kHz 3kHz deviation and of IC504). input signal of 1mV, can the sine wave be seen at Pin 25 of IC504?
Page 21
Unit [V] Unit [V] Ref. Ref. STBY TALK Note STBY TALK Note 1.8~2.0 0.0~2.7 0.0~3.3 0.0~3.3 0.0~3.3 DATA 0.0~0.7 0.3~0.6 0.0~3.3 DATA 0.0~0.7 0.3~0.6 0.0~3.2 DATA 0.0~3.0 0.0~3.2 DATA IC503 IC504 0.0~3.2 DATA 0.0~3.2 DATA 0.0~3.3 0.0~0.3 0.0~3.2 DATA 0.0~0.3 0.0~1.6 0.0~1.5 0.0~2.6...
PARTS LIST PRODUCT SAFETY NOTE: Products marked with a have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice of this service manual. Don't degrade the safety of the product through important servicing. Symbol Symbol ±...
Page 34
LOC. PART NO. DESCRIPTION RC004492 BCUA818204Z CERAMIC 82PF 50V J CH RC004608 BCUB312245Z CERAMIC 0.22UF 16V K B RC004500 BCUB812235Z CERAMIC 0.022UF 50V K B RC004561 BCUB813935Z CERAMIC 0.039UF 50V K B RC004945 BCAP111016Z ELECTROLYTIC 100UF 10V M C-130 RC004562 RCUB814725Z CERAMIC 0.0047UF 50V K B...
Page 35
LOC. PART NO. DESCRIPTION RC004500 BCUB812235Z CERAMIC 0.022UF 50V K B RC004740 BCUE813091Z CERAMIC 3PF 50V C CJ RC004496 BCUB811025Z CERAMIC 0.001UF 50V K B RC004659 BCXB811025Z CERAMIC 0.001UF 50V K B RC004659 BCXB811025Z CERAMIC 0.001UF 50V K B RC004497 BCUB811035Z CERAMIC 0.01UF 50V K B...
Page 36
LOC. PART NO. DESCRIPTION C521 RC004185 BCSS951006Z TANTALUM CHIP 10UF 7V M A C-241 C522 RC004497 BCUB811035Z CERAMIC 0.01UF 50V K B C523 RC004491 BCUA816804Z CERAMIC 68PF 50V J CH C524 RC004488 BCUA814714Z CERAMIC 470PF 50V J CH C525 RC004502 BCUB814735Z CERAMIC 0.047UF 50V K B...
Page 37
LOC. PART NO. DESCRIPTION C569 RC005166 BCUP311050Z CERAMIC 1UF 16V Z F C570 RC004741 BCUP811040Z CERAMIC 0.1UF 50V Z F C571 RC004490 BCUA816092Z CERAMIC 6PF 50V D CH C572 RC004496 BCUB811025Z CERAMIC 0.001UF 50V K B C573 RC004747 BCUA813314Z CERAMIC 330PF 50V J CH C574 RC004659...
ASSEMBLY PARTS LIST NOTE: Following part numbers are not available as replacement parts. Order parts necessary for repair or contact the Toshiba Factory Service Center. LOC. PART NO. DESCRIPTION AD559ZLBA BASE MAIN ASSEMBLY RC008805 RC008806 AD559ZLPA HANDSET MAIN ASSEMBLY — 48 —...
SPECIFICATIONS MEASUREMENT CONDITIONS 1. Standard voltage: Handset: DC 3.6 V ±0.025 V AC 120 V ±3 V 60 Hz Base: 25°C ±5 °C 2. Temperature: 3. Channel: Handset (TX Frequency) Base (TX Frequency) 48.760 MHz 43.720 MHz 48.840 MHz 43.740 MHz 48.860 MHz 43.820 MHz 48.920 MHz...
Page 49
BASE UNIT RECEIVER Unit Nominal Limit µV 1. Sensitivity 12 dB SINAD 2. Bandwidth at 6 dB down −3.5 −7.5 ~ +0.5 3. Frequency Response 0.3 kHz −5 −9 ~ −1 3.0 kHz 4. Distortion at 1 mV Input 5. S/N ratio at 1 mV RF Input TRANSMITTER 1.
Page 50
HANDSET UNIT RECEIVER Unit Nominal Limit µV 1. Sensitivity 12 dB SINAD 2. Bandwidth at 6 dB down −3 −7 ~ +1 3. Frequency Response 0.3 kHz −6 −10 ~ −2 3.0 kHz 4. Audio Output Power at 1 mV Input 75 ~ 170 5.
2) Press CID (Caller ID) button. Then, the Caller ID memory will be deleted with the confirmation beep sound. Information of the Serial No. for Model FT-7807R The production of Model FT-7807R was started in April 1998, and the Serial No. started from 846000001. — 52 —...