Important Safety Instructions 1. Read these instructions. 20. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 2. Keep these instructions. Rules. These limits are designed to provide reasonable protection 3.
TH-15A FREQUENCY GRAPH ......... 14 TH-15A BLOCK DIAGRAM ........15 MACKIE LIMITED WARRANTY ........ 16 Please write the serial number for your TH-15A here (or for both TH-15As if you have two) for future reference (i.e., insurance claims, tech support, return authorization, etc.):...
3. Slowly turn up the LEVEL control on the TH-15A to the “U” (unity gain) mark at the center position. 4. Adjust the master volume on your mixer to a comfortably loud listening level.
INPUT THRU INPUT FX MASTER FX TO MON PHONES TAPE LEVEL MAIN MUTE MUTE MUTE MUTE MUTE MUTE ST RTN FX RTN The left and right line-level outputs from a mixer feed the inputs of two Mackie TH-15A Powered Loudspeakers.
Page 6
FX RTN The left and right line-level outputs from a For microphone connections, you can daisy-chain mixer feed the inputs of two Mackie TH-15A up to two TH-15As using the THRU jack, as shown. Powered Loudspeakers. Their respective THRU jacks feed the inputs of another pair of Mackie Take great care to point any microphones away TH-15A Powered Loudspeakers.
Page 7
(Mackie SRM1801) The left and right line-level outputs from a mixer feed the inputs of two powered subwoofers. The high pass line-level outputs of the subwoofers feed the inputs of the Mackie TH-15A loudspeakers. PA System with one powered subwoofer...
This is a male XLR-type connector that produces to the input of the TH-15A. This could damage the exactly the same signal that is connected to the input active input circuitry of the loudspeaker.
This control gives you up to 15 dB of boost or cut The OL (overload) indicator lights when the amplifiers in the TH-15A are near the clipping point. It (U). This frequency range represents the punch in bass is okay if the OL indicator blinks occasionally, because...
(i.e., frequent OL LED indications, excessive distortion), Driver Protection you can still damage the speakers in the TH-15A by overdriving them past the point of amplifier clipping. Such Each driver has its own compression circuit, which damage is beyond the scope of the warranty.
If are certain that the AC outlet is live, it is possible the problem switches sides, it’s not the TH-15A. It the fuse has blown. could be a bad cable, or no signal from the mixer.
XLR Connectors noises or hum. XLR connectors are used to make balanced input and through connections to the TH-15A. They are wired loudspeakers, try plugging them all into the same as follows, according to standards specified by the AES AC outlet panel or outlet strip. The purpose for (Audio Engineering Society).
50 watts into 4 ohms Mounting Methods: Design: Class AB Pole-mountable via the built-in socket on the bottom of the cabinet. Be sure the pole is capable of supporting the weight of the TH-15A. Crossover Type: 24 dB/octave Crossover Frequency: 3 kHz...
26.2 in / 702 mm 666 mm 8.8 in / 222 mm WEIGHT 36 lb 16.3 kg 5.9 in / 151 mm 24.9 in / 633 mm 16.8 in / 15.5 in / 427 mm 394 mm TH-15A Frequency Response...
Therefore, we reserve the right to change these specifications at any time without notice. “Mackie,” and the “Running Man” are registered trademarks of LOUD Technologies Inc. All other brand names mentioned are trademarks or registered trademarks of their respective holders, and are hereby acknowledged.
The Product Warranty will not extend to anyone other than the original purchaser of the product (hereinafter, “Customer,” “you” or “your”). For products purchased outside the U.S. or Canada, please visit www.mackie.com/warranty to find contact information for your local distributor, and information on any warranty coverage provided by the distributor in your local market.