Table of Contents
Advertisement
2-4: OSD POSITION
1.
Receive the monoscope pattern from the Pattern
Generator.
2.
Using the remote control, set the brightness and
contrast to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (00) on the remote control to
select "OSD H".
4.
Press the VOL. UP/DOWN button on the remote control
until the difference of A and B becomes minimum.
(Refer to Fig. 2-1)
00 OSD H
A
2-5: HORIZONTAL POSITION/ HORIZONTAL SIZE
1.
Receive the monoscope pattern.
2.
Press the MENU button. And, then press the Channel
UP/DOWN button on the remote control until the
PICTURE menu appears.
3.
Press the VOL. UP/DOWN button on the remote
control to highlight DISPLAY FORMAT.
4.
Press the Channel UP/DOWN button on the remote
control to select 1080i.
5.
Set the screen mode to FULL.
6.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (02) on the remote control to
select "H.POSI".
7.
Press the VOL. UP/DOWN button on the remote
control until the SHIFT quantity of the OVER SCAN on
right and left becomes becomes minimum.
8.
Receive the monoscope pattern.
9.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (04) on the remote control to
select "H. SIZE".
10.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on right and
left becomes 7.5%.
ELECTRICAL ADJUSTMENTS
TV-A
FULL
1
B
Fig. 2-1
2-6: VERTICAL CENT/ VERTICAL SIZE
1.
Receive the monoscope pattern.
2.
Press the MENU button. And, then press the Channel
UP/DOWN button on the remote control until the
PICTURE menu appears.
3.
Press the VOL. UP/DOWN button on the remote control
to highlight DISPLAY FORMAT.
4.
Press the Channel UP/DOWN button on the remote
control to select 1080i.
5.
Set the screen mode to FULL.
6.
Using the remote control, set the brightness and contrast
to normal position.
7.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (11) on the remote control to
select "V. CENT".
8.
Press the VOL. UP/DOWN button on the remote control
until the horizontal line becomes fit to the notch of the
shadow mask.
9.
Receive the monoscope pattern.
10.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (05) on the remote control to
select "V. SIZE".
11.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside and
downside becomes 8%.
2-7: VERTICAL LINEARITY
NOTE: Adjust after performing adjustments in section 2-6.
After the adjustment of Vertical Linearity, reconfirm
the Vertical Position and Vertical Size adjustments.
1.
Receive the monoscope pattern.
2.
Press the MENU button. And, then press the Channel
UP/DOWN button on the remote control until the
PICTURE menu appears.
3.
Press the VOL. UP/DOWN button on the remote control
to highlight DISPLAY FORMAT.
4.
Press the Channel UP/DOWN button on the remote
control to select 1080i.
5.
Set the screen mode to FULL.
6.
Using the remote control, set the brightness and contrast
to normal position.
7.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (06) on the remote control to
select "V. LIN".
8.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside and
downside becomes 8%.
D-2
Advertisement
Table of Contents
