TP-Link Archer D2 User Manual
  1. Manuals
  2. Brands
  3. TP-Link Manuals
  4. Wireless Router
  5. Archer D2
  6. User manual

TP-Link Archer D2 User Manual

Ac750 wireless dual band gigabit adsl2+ modem router
Hide thumbs Also See for Archer D2:
Table of Contents

Advertisement

Quick Links

Archer D2
AC750 Wireless Dual Band Gigabit ADSL2+ Modem
Router
Rev: 1.0.0
1910011088

Advertisement

Table of Contents
loading

Related Manuals for TP-Link Archer D2

Summary of Contents for TP-Link Archer D2

  • Page 1 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router Rev: 1.0.0 1910011088...
  • Page 2 Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.

  • Page 3: Fcc Statement

    FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

  • Page 4: National Restrictions

    This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction...

  • Page 5: Industry Canada Statement

    Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations.

  • Page 6: Safety Information

    Safety Information When product has power button, the power button is one of the way to shut off the product;  when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself.

  • Page 7: Declaration Of Conformity

    DECLARATION OF CONFORMITY For the following equipment: Product Description: AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router Model No.: Archer D2 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:...

  • Page 8: Table Of Contents

    CONTENTS Package Contents ....................1 Chapter 1. Product Overview ................... 2 1.1 Overview of the Modem Router ..................2 1.2 Main Features ....................... 3 1.3 Panel Layout ......................... 4 1.3.1 The Front Panel ........................4 1.3.2 The Back Panel ........................6 Chapter 2.
  • Page 9 4.7.2 Clients List .......................... 38 4.7.3 Address Reservation ......................38 4.7.4 Conditional Pool ......................... 39 4.8 Wireless 2.4GHz ......................41 4.8.1 Basic Settings ........................41 4.8.2 WPS Settings ........................42 4.8.3 Wireless Security ....................... 44 4.8.4 Wireless Schedule ......................46 4.8.5 Wireless MAC Filtering ......................
  • Page 10 4.14 Forwarding ........................73 4.14.1 Virtual Server ........................73 4.14.2 Port Triggering ........................75 4.14.3 DMZ ..........................76 4.14.4 UPnP ..........................77 4.15 Parental Control ......................78 4.16 Firewall ........................79 4.16.1 Rule ..........................79 4.16.2 LAN Host .......................... 80 4.16.3 WAN Host .........................
  • Page 11 Appendix A: Specifications ................. 105 Appendix B: Troubleshooting ................106 Appendix C: Technical Support ................109...

  • Page 12: Package Contents

    Quick Installation Guide  One RJ45 cable  Two RJ11 cables  One ADSL splitter  One Resource CD for Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router,  including: This User Guide • Other Helpful Information • ...

  • Page 13: Chapter 1. Product Overview

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Chapter 1. Product Overview Thank you for choosing the Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router. 1.1 Overview of the Modem Router The Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP.

  • Page 14: Main Features

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 1.2 Main Features Complies with IEEE 802.11ac to provide a wireless data rate of up to 300Mbps (2.4GHz) +  450Mbps (5GHz). Four 10/100/1000Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), one RJ11 port.

  • Page 15: Panel Layout

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The modem router’s LEDs are located on the top panel (View from top to bottom). They indicate the device’s working status. For details, please refer to LED Explanation.
  • Page 16 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide At least one LAN port is connected. (LAN) No LAN port is connected. The wireless 2.4GHz/5GHz band is working properly. (Wireless) The wireless function is disabled. The network is available with a successful Internet connection.

  • Page 17: The Back Panel

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 1.3.2 The Back Panel Figure 1-2 ADSL: Through the port, you can connect the telephone to the modem router. Or you can  connect them by an external separate splitter. For details, please refer to 2.3 Connecting the...

  • Page 18: Chapter 2. Connecting The Modem Router

    Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of Archer D2. Connect the other end to the MODEM port of the external splitter. Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s Ethernet port or a regular hub/switch port, and the other end to the LAN port on the modem router Archer D2.
  • Page 19 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 2-1...

  • Page 20: Chapter 3. Quick Installation Guide

    AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router using Quick Setup Wizard within minutes.

  • Page 21: Quick Installation Guide

    192.168.1.2 ~ 192.168.1.254. 3.2 Quick Installation Guide With a Web-based utility, it is easy to configure and manage the Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
  • Page 22 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 3-3 Step 3. The Quick Setup page will appear for you to quickly configure your modem router. Click Next to continue. Figure 3-4 Step 4. Select the Region and the Time Zone from the drop-down list, and then click Next.
  • Page 23 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 3-7 Step 7. Configure the basic parameters for 2.4GHz wireless network, and then click Next. Figure 3-8 Step 8. Configure the basic parameters for 5GHz wireless network and then click Next.
  • Page 24 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 3-10 Step 10. You will see the Complete screen below. Click Finish to complete these settings. Figure 3-11 The basic settings for your modem router are completed. Please open the web browser and try to log on to http://www.tp-link.com...

  • Page 25: Chapter 4. Configuring The Modem Router

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Chapter 4. Configuring the Modem Router This chapter will show configuration for the key functions on the Web-based management page. 4.1 Login After your successful login, you will see the twenty-three main menus on the left of the Web-based utility.

  • Page 26: Status

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.2 Status Choose “Status”, you can see the corresponding information about Device Information, DSL, WAN, LAN and Wireless.
  • Page 27 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-1...

  • Page 28: Quick Setup

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.3 Quick Setup Please refer to 3.2 Quick Installation Guide. 4.4 Operation Mode Choose “Operation Mode”, and you will see the screen as shown in Figure 4-2. Select your desired mode and then click Save.

  • Page 29: Wan Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.5.1 WAN Settings Choose “Network”“WAN Settings”, and you will see the WAN Port Information Table in the screen similar to Figure 4-3. There are six different configurations for the connection types, which are Static IP, Dynamic IP, PPPoE, PPPoA, IPoA and Bridge.
  • Page 30 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-4 4.5.1.1 Static IP Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below.
  • Page 31 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-5 ATM Configuration: VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range  is from 0 to 255. Please input the value provided by your ISP.
  • Page 32 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Gateway (Optional): Enter the gateway IP address in dotted-decimal notation provided by  your ISP. DNS Server/ Secondary DNS Server: Here you can set DNS Server (at least one) manually.
  • Page 33 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-6 Click Advance, advanced selections for WAN Service Setup can be shown.  MTU (bytes): The default MTU (Maximum Transmission Unit) value is 1500 Bytes. Do not change the default value unless required by your ISP.
  • Page 34 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Set IPv6 DNS Server manually: Choose “Set IPv6 DNS Server manually”, you can set IPv6 DNS Server manually here. The modem router will use this IPv6 DNS Server for priority.
  • Page 35 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Connect on demand: This mode is dependent on the traffic. If there is no traffic (or Idle) for a  pre-specified period of time (MAX Idle Time), the connection will drop down automatically.
  • Page 36 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-8 4.5.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the Connection Type on the screen.

  • Page 37: Bridge

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-9 IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP.  DNS Server/Secondary DNS Server: Type in your preferred DNS server.  Default Gateway: Select a WAN Interface from the drop-down list as the IPv4 default ...

  • Page 38: Interface Grouping

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Note: After you finish the Internet configuration, please click Save to make the settings take effect. 4.5.2 Interface Grouping Choose “Network”“Interface Grouping”, you can view all the current groups on this page (shown in Figure 4-11).

  • Page 39: Lan Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-12 Click Save to make the entry effective immediately 4.5.3 LAN Settings Choose “Network”“LAN Settings” menu, and you will see the LAN screen (shown in Figure 4-13). Please configure the parameters for LAN ports according to the descriptions below.

  • Page 40: Ipv6 Lan Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Enable IGMP Snooping: IGMP Snooping is the process of listening to IGMP (Internet Group  Management Protocol) network traffic. The feature prevents hosts on a local network from receiving traffic for a multicast group they have not explicitly joined.

  • Page 41: Mac Clone

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-15 • Start IPv6 Address: Enter a value for the DHCPv6 server to start with when issuing IPv6 addresses. • End IPv6 Address: Enter a value for the DHCPv6 server to end with when issuing IPv6 addresses.

  • Page 42: Alg Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide The WAN Interface List displays the WAN Interfaces you have configured on the section 4.5.1 WAN Settings and its default MAC Address. You can select the corresponding WAN Interface from the drop-down list and click Clone MAC To button to clone your current PC MAC, and then click Save.

  • Page 43: Dsl Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide IPSec Pass-through: IPSec (Internet Protocol security) is a suite of protocols for • ensuring private, secure communications over Internet Protocol (IP) networks, through the use of cryptographic security services. To allow IPSec tunnels to pass through the modem router, click Enable.
  • Page 44  Note: You could also use other VPN Routers to set VPN tunnels with Archer D2. Archer D2 supports up to 10 VPN tunnels simultaneously. Click Add New Connection in Figure 4-21 and then you will enter the screen shown in Figure 4-22.
  • Page 45 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Remote IPSec Gateway Address (URL): Enter the destination gateway IP address which is the public WAN IP or Domain Name of the remote VPN server endpoint. (For example: Input 219.134.112.247 in Device1, Input 219.134.112.246 in Device 2)

  • Page 46: Iptv

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-23  Mode: Select Main Mode to configure the standard negotiation parameters for IKE phase1. Select Aggressive Mode to configure IKE phase1 of the VPN Tunnel to carry out negotiation in a shorter amount of time.

  • Page 47: Dhcp Server

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-24 Enable IPTV: Check the box to enable IPTV function.  VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range ...
  • Page 48 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-25 Group/ IP Address/ Subnet Mask: Displays group name, IP address and subnet mask.  The parameters can be configured on the Interface Grouping page and LAN Settings page.

  • Page 49: Clients List

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Note: To use the DHCP server function of the modem router, you must configure all computers on the LAN as "Obtain an IP Address automatically". You have to disable NAT of the WAN connections, or the DHCP Relay may not take effect.

  • Page 50: Conditional Pool

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-27 MAC Address: The MAC address of the PC for which you want to reserve an IP address.  IP Address: The IP address reserved for the PC by the modem router.
  • Page 51 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-29 To add a vendor class: Click the Add New button. Then Figure 4-30 will pop up. Enter parameters for the vendor class. Click the Save button.

  • Page 52: Wireless 2.4Ghz

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Wireless 2.4GHz There are seven submenus under the Wireless 2.4 GHz menu: Basic Settings, WPS Settings, Wireless Security, Wireless Schedule, Wireless MAC Filtering, Wireless Advanced and Wireless Status. Click any of them, and you will be able to configure the corresponding function.

  • Page 53: Wps Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 11bg mixed: Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed: Select if you are using a mix of 802.11b, 11g, and 11n wireless clients.
  • Page 54 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Note: To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function meanwhile. Use the Wi-Fi Protected Setup Button Use this method if your client device has a Wi-Fi Protected Setup button.

  • Page 55: Wireless Security

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-34 Step 2: Enter the PIN number from the client device in the field on the above WPS screen. Then click Connect button. Step 3: “Connect successfully” will appear on the screen of Figure 4-34, which means the client device has successfully connected to the modem router.
  • Page 56 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-35 Disable Wireless Security: If you do not want to use wireless security, check this radio  button. But it’s strongly recommended to choose one of the below modes to ensure security.

  • Page 57: Wireless Schedule

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide authentication type automatically based on the wireless station's capability and request. Encryption: You can select Auto, TKIP or AES as Encryption. • RADIUS Server IP: Enter the IP address of the Radius Server.

  • Page 58: Wireless Mac Filtering

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-36  Note: The time you set is the period you need the wireless off. Before configure the wireless schedule, please set system time first which refer to 4.23.2 Time...
  • Page 59 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-37 To filter wireless users by MAC Address, click Enable. The default setting is Disabled. MAC Address: The wireless station's MAC address that you want to filter.

  • Page 60: Wireless Advanced

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Modify the information. Click the Save button. Click the Enable/ Disabled Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete the selected entries.

  • Page 61: Wireless Status

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Beacon Interval: Enter a value between 25-1000 milliseconds for Beacon Interval here. The  beacons are the packets sent by the modem router to synchronize a wireless network.

  • Page 62: Wireless 5Ghz

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Wireless 5GHz There are seven submenus under the Wireless 5GHz menu: Basic Settings, WPS Settings, Wireless Security, Wireless Schedule, Wireless MAC Filtering, Wireless Advanced and Wireless Status. Click any of them, and you will be able to configure the corresponding function.

  • Page 63: Wps Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Channel: Select the channel you want to use from the drop-down List of Channel. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.
  • Page 64 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-42 WPS: Enable or disable the WPS function here.  Current PIN: The current value of the modem router's PIN is displayed here.  Restore PIN: Restore the PIN of the modem router to its default.

  • Page 65: Wireless Security

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Step 2: Press and hold the WPS button of the client device directly. Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process.
  • Page 66 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-45 Disable Wireless Security: If you do not want to use wireless security, check this radio  button. But it’s strongly recommended to choose one of the below modes to ensure security.

  • Page 67: Wireless Schedule

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Encryption: You can select Auto, TKIP or AES as Encryption. • RADIUS Server IP: Enter the IP address of the Radius Server. • RADIUS Server Port: Enter the port that radius service used.

  • Page 68: Wireless Mac Filtering

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-46  Note: The time you set is the period you need the wireless off. Before configure the wireless schedule, please set system time first which refer to 4.23.2 Time...
  • Page 69 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-47 To filter wireless users by MAC Address, click Enable. The default setting is Disabled. MAC Address: The wireless station's MAC address that you want to filter.

  • Page 70: Wireless Advanced

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Click the Save button. Click the Enable/ Disabled Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete the selected entries. For example: If you desire that the wireless station A with MAC address 00:1D:0F:11:22:33 and the...
  • Page 71 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-49 Transmit Power: Here you can specify the transmit power of the modem router. You can  select 100%, 50% or 25%. 100% is the default setting and is recommended.

  • Page 72: Wireless Status

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.9.7 Wireless Status Choose menu “Wireless 5GHz””Wireless Status”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-50 MAC Address: The connected wireless station's MAC address ...

  • Page 73: Guest Network Status

    SSID: The guest network name. When setting up a Guest network, it is strongly  recommended to use a name that easily distinguishes it from your primary network. The default name is TP-LINK Guest_XGHz. Security: It’s strongly recommended to enable WPA/WPA2-Personal. ...

  • Page 74: Usb Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Received Packets: Packets received by the station.  Sent Packets: Packets sent by the station.  Click on the Refresh button to update this page. 4.11 USB Settings There are six submenus under the USB Settings menu, USB Mass Storage, User Accounts, Storage Sharing, FTP Server, Media Server and Print Server.

  • Page 75: User Accounts

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Status: Indicates the shared or non-shared status of the volume. Active means volume can  be shared, while Inactive means volume can not be shared. If Inactive in Action field is enabled, Active will be displayed in the Status field, which means volume can not be shared.

  • Page 76: Storage Sharing

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.11.3 Storage Sharing Choose menu “USB Settings” → “Storage Sharing”, you can configure a USB disk drive attached to the modem router and view volume and share properties on this page as shown below.

  • Page 77: Ftp Server

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-57 Click the Browse button, and then select the Select Volume from the drop-down list. Enter the display name of the share folder in Share Name filed.
  • Page 78 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-58 Server Status: Indicates the FTP Server's current status.  Internet Access: If Internet Access is enabled, user(s) in public network can access FTP  server via Internet Address.

  • Page 79: Media Server

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-59 Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed. Click the Apply button to apply the settings.

  • Page 80: Print Server

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Enter the name of the share folder in Share Name field. Click the Apply button to apply the configuration. Figure 4-61 Click the Scan now to scan all the share folders immediately. You can also select the Auto-scan, and, at the same time, select an auto scan interval time from the drop-down list.

  • Page 81: Default Gateway

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.12.1 Default Gateway Choose “Route Settings”“Default Gateway”, you can see the Default Gateway screen. You can select a WAN Interface from the drop-down list as the system default gateway.

  • Page 82: Rip Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Destination IP Address: The address of the network or host that you want to assign to a  static route. Subnet Mask: It determines which portion of an IP Address is the network portion, and ...

  • Page 83: Ipv6 Static Route

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-67 Click the Add Interface button, you can add WAN Interfaces. Click the Save button to save your settings. 4.13.2 IPv6 Static Route Choose “IPv6 Route Settings” “IPv6 Static Route”. You can see the IPv6 Static Route screen.

  • Page 84: Forwarding

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Prefix Length: The prefix length of the destination IPv6 address.  Gateway: Type in the correct IPv6 Gateway address for the IPv6 Static Route.  Interface: Select the Interface from the drop-down list.
  • Page 85 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide IP Address: The IP address of the PC running the service application.  Protocol: The protocol used for this application. The options are TCP, UDP, or All (all ...

  • Page 86: Port Triggering

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Otherwise there will be a conflict to disable the virtual server. 4.14.2 Port Triggering Choose menu “Forwarding”→ “Port Triggering”, you can view and add port triggering in the next screen (shown in Figure 4-72).

  • Page 87: Dmz

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Interface: Display the default gateway you have set in 4.5.1 WAN Settings.  Trigger Port: The port for outgoing traffic. An outgoing connection using this port will trigger ...

  • Page 88: Upnp

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-74 To assign a computer or server to be a DMZ server: Click the Enable button. Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field.

  • Page 89: Parental Control

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Status: Either Enabled or Disabled. "Enabled" means that the port is still active; • otherwise, the port is inactive. Click the Enable button to enable UPnP. Click the Disable button to disable UPnP.

  • Page 90: Firewall

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide MAC Address of Current PC: This field displays the MAC address of the PC that is  managing this modem router. If the MAC Address of your adapter is registered, you can click the Copy To Above button to fill this address to the MAC Address of Parental PC field above.

  • Page 91: Lan Host

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Status: Here displays the status of the rule, enabled or not.  Edit: Here you can edit or delete an existing rule. Click the Enable /Disable Selected button to enable or disable the selected rules in the list.

  • Page 92: Wan Host

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-79 Description: Here displays the description of the host and this description is unique.  Address Info: Here displays the information about the host. It can be IP or MAC.
  • Page 93 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-81 In Description field, create a unique description for the host (e.g. Host_1). In IP Address field, enter the IP address. If you select MAC Address, the screen shown is Figure 4-82.

  • Page 94: Schedule

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.16.4 Schedule Choose menu “Firewall” → “Schedule”, and then you can view and set a Schedule list in the next screen as shown in Figure 4-84. Figure 4-84 Description: Here displays the description of the schedule and this description is unique.

  • Page 95: Ipv6 Firewall

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.17 IPv6 Firewall There are four submenus under the IPv6 Firewall menu: IPv6 Rule, IPv6 LAN Host, IPv6 WAN Host and IPv6 Schedule. Click any of them, and you will be able to configure the corresponding function.

  • Page 96: Ipv6 Lan Host

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-87 Give a name (e.g. Rule_1) for the rule in the Description field. Select a host from the IPv6 LAN Host drop-down list or choose “Add IPv6 LAN Host”.

  • Page 97: Ipv6 Wan Host

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Edit: To modify an existing entry.  To add a new entry, please follow the steps below. Click the Add New button, and you will see the screen as shown in Figure 4-89.

  • Page 98: Ipv6 Schedule

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-91 Create a unique description for the host (e.g. Host_1) in the Description field. Enter an IPv6 address in the IPv6 Address field. Enter the prefix length of the IPv6 address in the Prefix Length field.

  • Page 99: Ipv6 Tunnel

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-93 Create a unique description for the schedule (e.g. Schedule_1) in Description field. Select the day or days you need in Apply To field. In time field, you can select all day-24 hours or you may enter the Start Time and End Time in the corresponding field.
  • Page 100 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-94 Enable: Check the box to enable IPv6 Tunnel function. It is disabled by default.  Mechanism: Select a type for IPv6 tunnel from the drop-down list. DS-Lite, 6RD and 6to4 are ...
  • Page 101 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-96 WAN Connection: Select a WAN connection from the drop-down list. Only the connected  WAN connections can be shown in the drop-down list. Configuration Type: Select a configuration type for this tunnel. Auto means to obtain the ...

  • Page 102: Bandwidth Control

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.19 Bandwidth Control Choose menu “Bandwidth Control”, and then you can configure the Upstream Bandwidth and Downstream Bandwidth in the next screen. The values you configure should be less than 1000000Kbps.

  • Page 103: Ip&Mac Binding

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-99 Click the Save button. Click the Enable/ Disable Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete the selected entries.

  • Page 104: Arp List

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Edit button, and then you will go to the next page. This page is used for adding or modifying an IP &...

  • Page 105: Dynamic Dns

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Click the Delete Selected button to delete the selected entries. Click the Refresh button to refresh all items. 4.21 Dynamic DNS Choose menu “Dynamic DNS”, and you can configure the Dynamic DNS function.

  • Page 106: System Tools

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-104 4.23 System Tools Choose menu “System Tools”, and you can see the submenus under the main menu: System Log, Time Settings, Manage Control, CWMP Settings, SNMP Settings, Backup & Restore, Factory Defaults, Firmware Upgrade, Reboot and Statistics.

  • Page 107: Time Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-105 Log Type: Select the log type to be displayed.  Log Level: Select the log level to be displayed.  Refresh: Refresh the page to show the latest log list.

  • Page 108: Manage Control

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-107 Time Zone: Select your local time zone from this drop-down list.  Date: Enter your local date in MM/DD/YY into the right blanks.  Time: Enter your local time in HH/MM/SS into the right blanks.

  • Page 109: Cwmp Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-108 Current User Status: This box displays the information about User Type, User Name, Host  IP Address and Host MAC Address. Account Management: Here you can set the account user information about New User ...

  • Page 110: Snmp Settings

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-109 CWMP: Select Enable to enable the CWMP function.  Inform: If enabled, the information will be informed to ACS server periodically.  Inform Interval: Enter the interval time here.

  • Page 111: Backup & Restore

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-110 An SNMP Agent is an application running on the modem router that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs.

  • Page 112: Firmware Upgrade

    Click the Browse button to find the upgrade file on the computer. Click the Upgrade button.  Note: New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use.

  • Page 113: Reboot

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide When upgrade the modem router's firmware, you may lose its current configurations, so please write down some of your customized settings before upgrading the firmware. Do not turn off the modem router or press the Reset button while the firmware is being upgraded.
  • Page 114 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-115 Traffic Statistics: If it is disabled, the function of DoS protection in Security settings will be  disabled. The default value is disabled. To enable it, click the Enable.

  • Page 115: Logout

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Reset Reset the value of the entry to zero. Operation Delete Delete the existing entry in the table. 4.24 Logout Choose “Logout”, and you will back to the login screen as shown in Figure 4-116.
  • Page 116 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Appendix A: Specifications General ANSI T1.413, ITU G.992.1, ITU G.992.3, ITU G.992.5, IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE Standards and Protocols TCP/IP, PPPoA, 802.11ac, IEEE 802.3, IEEE 802.3u, IEEE802.3ab, PPPoE, SNTP, HTTP, DHCP, ICMP, NAT Safety &...
  • Page 117 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my modem router’s configuration to its factory default settings? With the modem router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it.
  • Page 118 Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4） Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. For Windows 8 1） Move your mouse to the lower right corner and you will see Search icon in the Popups.
  • Page 119 3.2 Quick Installation Guide. Please contact our Technical Support if the problem still exists.  Note: For more details about Troubleshooting and Technical Support contact information, please log on to our Technical Support Website: http://www.tp-link.com/en/support...

  • Page 120: Technical Support

    Archer D2 AC750 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Appendix C: Technical Support Technical Support  For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq  To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download ...

Table of Contents