Sony KP-48V75 Service Manual page 15

4
Press V or v to select CHANNEL ERASE/ADD,
and press .
The CHANNEL ERASE/ADD menu appears.
CHANNEL ERASE/ADD
33
ERASE
ADD
MENU
Use[0 – 9]or [CH+/–]
to select the channel.
Use Exit MENU
5
Erase and/or add channels:
To erase an unwanted channel
(1) Make sure the cursor (z) is beside ERASE.
(2) Press CH +/– or the 0 – 9 buttons to select the
channel you want to erase, and press ENTER.
Selected channel number
CH
1 2 3
CHANNEL ERASE/ADD
33
ERASE
or
4 5 6
ADD
MENU
7 8 9
Use[0 – 9]or [CH+/–]
ENTER
to select the channel.
0
Use Exit
MENU
(3) Press .
The "–" indication appears beside the channel
number, showing that the channel is erased
from the preset memory.
To add a channel that you want
(1) Press V or v to move the cursor (z) to ADD.
(2) Press the 0 – 9 buttons to select the channel you
want to add, and press ENTER.
Selected channel number
1 2 3
CHANNEL ERASE/ADD
33
4 5 6 ERASE
ADD
MENU
7 8 9
ENTER
0
Use Exit
MENU
(3) Press .
The "+" indication appears beside the channel
number, showing that the channel is added to
the preset memory.
6
To erase and/or add other channels, repeat
step 5.
7
Press MENU to return to the original screen.
MENU
Notes
• If you erase or add a VHF or UHF channel, the cable TV
channel with the same number is also erased or added, and
vice versa.
• Erasing and adding channels is also available for the AUX
input.
Adjusting convergence
(CONVERGENCE)
The projection tube image appears on the screen in
three layers (red, green and blue). If they do not
converge, the color is poor and the picture blurs. To
correct this, adjust convergence.
You do not have to do this procedure if you perform
AUTO SET UP (page 21). Do this procedure only
when you want to adjust it manually.
1
Press MENU.
2
Press V or v to select , and press .
3
Press V or v to select CONVERGENCE, and
press .
The CONVERGENCE adjustment screen appears.
R
CONVERGENCE
G
+
RED
+ BLUE
B
MENU
B
Us e RETURN E x i t MENU
G
R
R=Red
G=Green
B=Blue
Getting Started 23 -EN
4
Press V or v to move the cursor (z) to the
symbol showing the line you want to
adjust, and press .
CONVERGENCE
+ RED
+
BLUE
MENU
Us e
+RED : Red vertical and horizontal line (left/right/up/
down adjustment)
+BLUE : Blue vertical and horizontal line (left/right/up/
down adjustment)
5
Press V, B, v, or b to move the line until it
converges with the center green line, and
press .
R
CONVERGENCE
G
+ RED
+
BLUE
B
MENU
B
EN Us e
G+R
To move Press
Up V
Down
v
Right b
Left B
6
Repeat steps 4 and 5 to adjust the other
lines until all three lines converge and are
seen as a white cross.
7
Press MENU to return to the original screen.
24 -EN Getting Started
Setting cable TV on or off
If you have connected the projection TV to a cable TV
system, set CABLE to ON (the factory setting). If not,
set CABLE to OFF.
You do not have to do this procedure if you perform
AUTO SET UP (page 21). Do this procedure only when
RETURN E x i t MENU
you want to set it manually.
1
Press MENU.
2
Press V or v to select , and press
3
Set CABLE to ON or OFF:
(1) Press V or v to move the cursor (z) to CABLE,
and press .
(2) Press V or v to select ON or OFF, and press
CC
RETURN E x i t MENU
Use
4
Press MENU to return to the original screen.
Note
• If CABLE appears in gray, the projection TV is set to a video
input and you cannot select CABLE. Press ANT so that a
channel number appears.
.
.
SET UP
CHANNEL ERASE/ADD
CHANNEL CAPTION
CHANNEL BLOCK
FAVORITE CHANNEL
CABLE : OFF
AUTO PROGRAM
VIDEO LABEL
LANGUAGE : ENGLISH
CONVERGENCE
MENU
Exit MENU