PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
TIMING CHART VIDEO SYNC Total Video Blanking Sync Back Front Sync Frequency MODE H / V Resolution Period Active Time Duration Porch Porch Polarity Clock ( E ) Time ( A ) ( B ) ( D ) ( F ) ( C ) 25.175 31.469 KHz...
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW D-Sub Signal Connector Power Button Power Indicator DC Power Connecter OSD Button AUTO/SET Button Buttons Front Control Panel 1. Power ON/OFF Button 4 AUTO/SET Button Use this button to enter a selection in the on screen display. Use this button to turn the monitor on or off.
Page 6
Listed below are icons, icon names, and icon descriptions On-Screen-Display (OSD) Control of the OSD menu. To adjust an image size, position, and operating parameters are quick and easy with the On-Screen- BRIGHTNESS CONTRAST Display control system, using the OSD button and the Adjustment control button.
Page 7
TRACKING SETUP TRACKING SETUP LANGUAGE ENGLISH FULL CLOCK IMAGE SIZE OSD POSITION PHASE MODE INFO 48 .3 kHz / 6 0. 0Hz PRESET M O DE LANGUAGE To choose the language in which the To minimize any vertical bars or CLOCK control names are displayed.
CONTROL LOCATIONS Ref. No. Control Function SW301 OSD BUTTON SW304 ADJUST LEFT MAIN PCB SW303 ADJUST UP SW306 ADJUST DOWN SW302 ADJUST RIGHT SW307 AUTO/SET CONTROL PCB SW305 POWER SWITCH WIRING DIAGRAM J301...
DISASSEMBLY 1. TILT/SWIVEL REMOVAL 2. BACK COVER REMOVAL (1) Remove two screws (a). (1) Remove four sheet (a) from Back Cover. (2) Remove the Tilt/swivel. (2) Remove four screws (b) from the Back Cover. (3) Remove the Back Cover. Back Cover 3.
Page 10
5.METAL FRAME ASSEMBLY REMOVAL (1) Remove five screws (a). (2) Remove six screws (b). (3)Remove theMetal Frame Ass’y 5. INVERYTER REMOVAL 6. BACKLIGHT REMOVAL (1) Disconnect CN2,CN3 . (1) Remove two screws (a). (1) Remove two screws (a). (2) Remove the Backlight from the LCD Module. (2) Remove the Inverter.
3.3V Memory 3.3V Video Signal 3.3V (KM416S102BT) Reg. R,G,B differential Address Data 48 Bit M-CLK 5.0V 3.3V Out - CLK LVDS Inverter DC-DC R,G,B Even 3.3V (LVDS8 3) Converter Video Controller DE ,H/V Sync out ADC CLK LCD Module Out - CLK MX88L282 LVDS 24V Input...
DESCRIPTION OF BLOCK DIAGRAM 1. Pre-amp/ ADC / PLL Part. This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the digital video signal using a pixel clock. The pixel clock for each mode is generated by the PLL. The range of the pixel clock is from 25MHz to 135MHz.
EEPROM. 1. Adjustment for Factory Preset Mode 8) Select PRESET EXIT command and Enter. 1) Run alignment program for FPD1570 on the IBM compatible PC. 2) Select EEPROM all clear command and Enter. 3) Display cross hatch pattern at Mode 1.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) TROUBLE IN CHECK U15 ADAPTOR or INPUT VOLTAGE INVERTER (24V) ? CHECK TROUBLE IN 5VST VOLTAGE (5V) ? CHECK U4 PIN 6. TROUBLE IN IS THIS PIN U4 or X2 OSCILLATED? TROUBLE SOMEWHERE ELSE...
Page 15
2. NO RASTER NO RASTER CHECK TROUBLE IN J4 PIN 10 POWER ADATER (24V) ? CHECK TROUBLE IN J4 PIN 5 (5V) ? INON PATTERN CHECK TROUBLE IN U4 PIN 42 U106, U105, U101, H. PULSE ? U109 CHECK TROUBLE IN U5 PIN 117 H.PULSE? CHECK...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS MODEL: FPD1570 DATE: 2000. 10. 11. LOC. NO. PART NO. DESCRIPTION / SPECIFICATION REMARK MAIN BOARD...
Page 24
MODEL: FPD1570 DATE: 2000. 10. 11. LOC. NO. PART NO. DESCRIPTION / SPECIFICATION REMARK 0CH8106J691 CAPACITOR, CHIP, [AL. ELECTROLYTIC], 10UF 35V M 105STD (CYL) R/TP 0CH3104K566 CAPACITOR, CHIP, [CERAMIC LD-LESS HD], 0.1UF 50V K X 2012 R/TP 0CH3104K566 CAPACITOR, CHIP, [CERAMIC LD-LESS HD], 0.1UF 50V K X 2012 R/TP 0CH3104K566 CAPACITOR, CHIP, [CERAMIC LD-LESS HD], 0.1UF 50V K X 2012 R/TP...
MX88L282 256PQFP BK XGA LCD INTEGRATION CHIP Pin Configurations GNDP 193 128 GNDP GNDP 194 127 GNDP W E # 126 GOUT1/OSDG0 CAS# 196 125 GOUT0/OSDB0 RAS# 197 124 L D T G DQM0 123 LVSYNC DQM1 122 LHSYNC G N D 121 VDDP GNDP 201 120 RA0...
Page 31
Chip Block Diagram SDRAM/SGRAM RGB/YUV PIXINA Color Brightness DRAM PIXINB Scale Down Scale up conversion Contrast controller with with (RGB or control SmartScaling SmartScaling YUV or Technology Technology YCrCb) PIXOUT - A (RGB) Odd/Even correction PIXOUT - B De-Interlace (RGB) Auto-tracking Auto-position CPU I/F...