Bosch WTB84200IL Instruction Manuals page 2

Only when switched off!
Care and cleaning Installation
Dryer housing, control panel
– Scope of delivery: dryer, operating and installation instructions, basket for woollens
– Wipe clean with a soft, damp cloth.
(depending on the model).
– Do not clean with a water jet. – Check the dryer for transport damage.
– Remove detergent and cleaning agent residue immediately. – The dryer is very heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– During drying, water may occasionally accumulate between the window and the seal.
– Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
This does not affect the proper operation of your dryer.
– Do not set up in a room that is susceptible to frost.
Heat exchanger
Freezing water may cause damage.
– If in doubt, have the appliance connected by a specialist.
The heat exchanger requires cleaning once a month,
however this varies depending on how frequently the dryer is used.
1. Setting up the dryer
Allow the dryer to cool down and place an absorbent cloth under the maintenance flap.
– The mains plug must always be accessible.
Residual water may escape. – Ensure that the appliance is placed on a clean, level and
firm surface.
1. Unlock the maintenance flap and open completely. – Do not obstruct the air inlet on the dryer.
2. Turn both locking levers towards each another. – Keep the area around the dryer clean.
– Level the dryer using the threaded feet
and a spirit level.
Never remove the threaded feet !
Do not install the dryer behind a door
3. Pull out the cap.
or sliding door which could prevent or
obstruct the dryer door from opening.
This will prevent children from locking
themselves in and risking their lives.
4. Remove the heat exchanger.
For mains connection,
2.
Take care not to damage the heat exchanger. – Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
When cleaning, use water only. Do not use hard or sharp-edged objects. – The mains voltage and the voltage shown on the rating plate (
– The connected load and necessary fuse protection are specified on the rating plate.
Converting the installed load
5. Rinse the heat exchanger and the cap on all sides with a jet of water to 3.
1. Turn the programme selector to Off.
completely remove all of the fluff.
2. Press and hold the
3. Turn the programme selector to Cottons Cupboard Dry Plus; wait until the recent setting
6. Remove any fluff from the seals on the dryer and heat exchanger.
appears in the display:
4. Press the Fine adjust button to change the settings.
7. Allow to drip dry fully. 5. Turn the programme selector to Off.
8. First insert the heat exchanger, then the cap.
9. Turn back both locking levers and close the
maintenance flap until it locks closed.
Frost protection / Transport
Moisture sensors
The dryer is equipped with stainless steel moisture sensors.
Preparation
Moisture sensors measure the moisture level of the laundry.
1. Empty the condensate container
After sustained, repeated operation, a fine layer of limescale
may form on the moisture sensors. 2. Select any programme using the programme selector.
3. Press the Start/Pause
4. Wait several minutes or until the dryer stops, and then empty the condensate container
1. Open the door.
again.
2. Clean the moisture sensors with a damp sponge which has a rough
5. Turn the programme selector to Off.
surface.
Do not use steel wool or abrasive agents!
8
Optional accessories
( order from the after-sales service using the order number, depending on the model)
WTZ Connection fittings for condensation outlet
1110 The condensation is conveyed directly via a hose.
WMZ Platform
20500 For easier loading and unloading. The basket contained in the drawer can be used
to carry the laundry.
Washer-dryer stack connection set
WTZ
11410 The dryer can be placed on top of a suitable washing machine with the same width and depth
Take all accessory parts out to save space. The dryer must be fastened to the washing machine using this connection set.
of the drum. WTZ 11400: with pull-out worktop.
The drum must be empty.
Technical data
Dimensions (DxWxH) 60 x 60 x 85 cm (height adjustable)
Weight approx. 45 kg
Max. capacity 7 kg
Condensation container 4.2 l
Connection voltage 220-240 V
Connected load 2100-2800 W
Fuse protection 10 A / 16 A
Ambient temperature 5-35°C
Product number
Inside of door
Clean and level
Production number
The rating plate can be found on the back of the dryer.
Make sure that the air inlet
remains unobstructed Consumption rates
Drum interior light (depending on model): The drum lights up after the door is opened
and after the programme starts, and switches off automatically.
see Safety instructions page 13. (The value on the label is achieved at the maximum heat setting.)
Residual moisture in the Drying time**
page 10) must be the same.
Fabrics/programmes
fabrics after spinning
Cottons 7 kg 10 A 16 A
Note the fuse protection of the socket ( 10/16 Amps.).
. Cupboard Dry* 1400 U/min (50%) 121 min 95 min
Fine adjust button. 1000 U/min (60%) 141 min 111 min
800 U/min (70%) 161 min 128 min
=10A or =16A.
Iron Dry* 1400 U/min (50%) 100 min 74 min
1000 U/min (60%) 119 min 88 min
800 U/min (70%) 140 min 100 min
Sinthetics 3.5 kg
800 U/min (40%) 52 min 46 min
. Cupboard Dry*
600 U/min (50%) 65 min 56 min
* Programme setting for testing in accordance with applicable standard DIN EN61121.
Do not operate the dryer if
there is a risk of frost. ** The values may differ from those specified, depending on the type of fabric, composition of
laundry to be dried, residual moisture in the fabric and the amount of laundry being loaded.
page 4/11.
button condensation is pumped into the container.
9
After-sales service What to do if ...
If you cannot rectify the fault yourself (e.g. switching off/on) What to do if..., page 11/12,
please contact our after-sales service. We will always find an appropriate solution and avoid
unnecessary visits by engineers.
The contact details of your local after-sales service can be found in the enclosed after-sales
service directory.
– GB 0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute.
A call set-up fee of up to 6 pence may apply.)
– IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
Please provide the after-sales service the product number (E no.) and the production number
(FD) of the appliance.
You can find this information:
inside the door* / in the opened service flap*
and on the rear of the appliance.
*depending on the model
Product number Production number
Trust the expertise of the manufacturer. Contact us for assistance. In this way, you can rest
assured that the repair will be carried out by trained service technicians using original spare
parts.
What to do if ...
Turn the programme selector to Off and remove the mains plug from the socket.
The Start/Pause indicator light Mains plug plugged in?
does not light up. Programme selected?
Check the socket fuse.
Energy
The display panel light and Energy-saving mode is activated see the separate
consumption**
indicator lights (depending on Energy-saving mode instructions.
10 A 16 A
model) go out and the Start/
3.36 kWh 3.36 kWh Pause indicator light flashes.
3.92 kWh 3.92 kWh
The display panel switches off. The appliance goes into the sleep mode after activating
4.48 kWh 4.48 kWh
Finished in option page 5.
2.42 kWh 2.42 kWh
The (Condensate container) Empty the condensate container page 4.
3.06 kWh 3.06 kWh
indicator light flashes. Press the Start/Pause button to reset the displayed
3.70 kWh 3.70 kWh indication and then press the Start/Pause button
again to restart the appliance if necessary.
If featured, check the hose for condensation outlet.
1.42 kWh 1.42 kWh
1.74 kWh 1.74 kWh (Fluff filter/Heat exchanger) Clean the fluff filter page 4.
indicator light flashes. Press the Start/Pause button to reset the displayed
indication and then press the Start/Pause button
again to restart the appliance if necessary.
Clean the heat exchanger page 8.
Dryer does not start. Start/Pause button selected?
Door closed?
Programme set?
11
10
Safety instructions
Programme terminates shortly Ambient temperature greater than 5°C?
Emergency – Pull the appliance plug out of the socket immediately or disconnect the fuse.
after starting. Is the appliance loaded with the laundry?
Load too small for selected programme?/Use timed ONLY use the – in rooms inside the house.
programme page 6/7. dryer... – to dry fabrics.
Loaded laundry dry?
The dryer must – be used for purposes other than those described above.
Water is leaking out. Make sure the dryer is level. NEVER... – be modified in terms of its technology or properties.
Clean the heat exchanger seal. Hazards – The dryer must not be used by children or persons who have not been
instructed in its use.
The door opens by itself. Push the door closed until you hear it engage.
– Do not leave children unsupervised near the dryer.
– Keep pets away from the dryer.
Creasing. Laundry load exceeded?
– Remove all objects from pockets, and lighters in particular
Remove articles of clothing immediately after the end
Risk of explosion.
of the programme, hang up and pull into shape.
– Do not lean or sit on the door
Unsuitable programme selected page 7.
Installation – Secure loose cables
Drying result is not satisfactory Warm laundry feels damper than it really is.
– Do not operate a dryer if there is a risk of frost.
(laundry feels too damp).
The selected programme does not suit the load. Use
Mains – Connect the dryer to an AC earthed socket according to specifications,
another drying programme or, in addition, select the connection otherwise it cannot be guaranteed that the appliance is completely safe.
timed programme page 7. – The cable cross-section must be sufficient.
+ – Only use earth-leakage circuit breakers with the following symbol:
Use Fine adjust for the dryness levels page 5.
– The appliance plug and socket must be compatible.
Fine layer of limescale on the humidity sensors – Do not use multiple plugs/connectors and/or extension cables.
Clean the moisture sensors page 8.
– Do not touch or hold the appliance plug with wet hands
Risk of electric shock.
Programme termination, e.g. tank full, mains power
– Never pull the appliance plug out of the socket by its cable.
supply failure, door open or maximum drying time
– Do not damage the mains lead
reached?
Operation – Only load the drum with laundry.
Drying time too long. Clean the fluff filter under running water page 4/11.
Check the contents before you switch the dryer on.
– Do not use the dryer if the laundry has been in contact with solvents, oil, wax,
Insufficient supply of air Ensure that air can circulate.
grease or paint (e.g. hair styling products, nail varnish remover, stain remover,
Air inlet possibly blocked Clear inlet page 9. cleaning solvent, etc.)
– Dust (e.g. coal dust, flour) poses a danger: Do not use the dryer
Ambient temperature higher than 35°C Ventilate the
Risk of explosion.
room.
– Do not put laundry containing foamed material/rubber in the dryer
One or more indicator lights are Clean the fluff filter and heat exchanger page 4,8/11. material may be destroyed and the dryer be damaged due to possible
flashing. Check the installation conditions page 9. deformation of the foamed material.
Switch off, allow to cool, switch back on and restart the – When cleaning the fluff filter, make sure that no foreign material (down or
programme. filling material) gets into the air duct opening. If necessary, clean the drum
beforehand with a vacuum cleaner. If foreign material should still get into the
Power failure. Remove the laundry from the dryer immediately and
air duct call the after-sales service
spread out. This allows the heat to dissipate. Be careful
– Light things, such as long hair, may be sucked into the air inlet of the dryer
as the door, the drum and the laundry may be hot.
Risk of injury.
– Switch off the dryer once the programme has ended.
– The water from condensation is not drinking water and may be contaminated
with fluff.
Defect – Do not use the dryer if it is defective or if you suspect that it is.
Repairs must only be carried out by the after-sales service.
– Do not use the dryer if the mains cable is defective. To avoid danger, only
have the defective mains cable replaced by the after-sales service.
Spare parts – For safety reasons, you must only use genuine spare parts and accessories.
Disposal – Pull out the appliance plug, then cut off the mains cable from the appliance.
Dispose of the appliance at a municipal waste disposal site.
– Packaging: Keep all packaging out of reach of babies and children
Risk of suffocation.
– All materials are environmentally sound and can be reused.
Dispose of them in an environmentally-responsible manner.
12
Risk of tipping.
Risk of tripping.
Risk of electric shock.
Risk of fire/explosion.
elastic
Risk of fire/explosion. Dryer
en Instruction manual
13