Page 1 Combined power zoom lens Illumination range Filter diameter 1 7/16 in. (37 mm) CCD-TR57/TR67/TR413PK : 0.4 lux hVIDEO CAMERA RECORDER CCD-TR57 : 16 x (Optical), 32 x to 100,000 lux (Digital) CCD-TR87/TR414PK/TR917/TR940/ CCD-TR67/TR87 : 16 x (Optical), 64 x TR940PK : 0.7 lux to 100,000 lux...
Page 2 Mass (Approx.) CCD-TR57 : 1 lb 11 oz (780 g) CCD-TR67/TR87/TR413PK/TR414PK/ TR917/TR940/TR940PK : 1 lb 11 oz (790 g) excluding the battery pack, lithium battery, cassette and shoulder strap CCD-TR57 : 2 lb (920 g) CCD-TR67/TR87/TR413PK/TR414PK/ TR917/TR940/TR940PK : 2 lb (930 g)
Page 3 – 3 –...
Page 4 Supplied accessories 1 Wireless Remote Commander (1) Except CCD-TR57 2 AC-L10A/L10B/L10C AC power adaptor 3 NP-F330 Battery pack (1) 4 CR2025 Lithium Battery (1) The lithium battery is already installed in your camcorder. 5 Size AA (R6) battery for Remote Commander (2)
Page 5: Power Supply During Repairs
SERVICE NOTE 1. POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. Battery switch This following two methods are available to prevent this.
Page 6: Self-Diagnosis Function
SELF-DIAGNOSIS FUNCTION 1. Self-diagnosis Function 2. Self-diagnosis display When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the counter of the function starts working, and displays on the viewfinder what to do. viewfinder shows a 4-digit display consisting of an alphabet and This function consists of two display;...
Page 7: Self-Diagnosis Code Table
4. Self-diagnosis Code Table Self-diagnosis Code Symptom/State Correction Block Detailed Function Code Condensation. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Video head is dirty. Non-standard battery is used. Use the InfoLITHIUM battery. LOAD direction.
Page 8: Table Of Contents
TABLE OF CONTENTS SERVICE NOTE 2. DISASSEMBLY Power Supply During Repairs ......... 5 2-1. Removal of Front Panel Block and Video Light Block ..2-1 To Take out a Cassette when not Eject (Force Eject) ..5 2-2. Removal of Cabinet (R) Block ......... 2-2 2-3.
Page 9 (VC-195 board) (CCD-TR917/TR940/TR940PK) ... 5-41 Bright Adjustment (VF-119 board) ......5-24 Standerd8 REC Y Current Adjustment (VC-195 board) Contrast Adjustment (VF-119 board) .....5-25 (CCD-TR57/TR67/TR87/TR413PK/TR414) ..5-42 Backlight Comsumption Current Adjustment Hi8 REC L Level Adjustment (VF-120 board) ............5-25 (VC-195 board) (CCD-TR917/TR940/TR940PK) ... 5-43 White Balance Adjustment (VF-119 board) ...5-25...
Page 10 6. REPAIR PARTS LIST 6-1. Exploded Views ............6-1 6-1-1. Cabinet (L) Block Assembly ........6-1 6-1-2. Front Panel Block Assembly (Except CCD-TR57) ...6-2 6-1-3. Front Panel Block Assembly (CCD-TR57) ....6-3 6-1-4. Cabinet (R) Block Assembly ........6-4 6-1-5. EVF Block Assembly ..........6-5 6-1-6.
Page 29: Disassembly
2-12. VC-195/SE-65 BOARDS NOTE : Follow the disassembly procedure in the numerical order given. 2-1. REMOVAL OF FRONT PANEL BLOCK AND VIDEO LIGHT BLOCK Cabinet (N) Two screws (M2x4) Except CCD-TR57 Cabinet (S) Screw (M2x4) Front panel block Two screws (M2x4)
Page 30: Removal Of Cabinet (R) Block
2-2. REMOVAL OF CABINET (R) BLOCK 2-3. REMOVAL OF EVF BLOCK-1 Note : Be sure to that the pin of the Lens assembly is put into the hole of the IR knob when attaching. (CCD-TR87/TR414PK/TR917/TR940/TR940PK) VF flexible retainer sheet Tapping screw Tapping screw VF base Three tapping...
Page 31: Removal Of Evf Block-2 (Lb-54, Vf-119 And Vf-120 Boards)
2-5. REMOVAL OF EVF BLOCK-2 (LB-54, VF-119 AND VF-120 BOARDS) Tilt-up the EVF block to the direction of arrow A . VF insulating sheet FP-638 flexible board CN5401,20P Remove the EVF rear cabinet assembly to the direction of arrow B . !¢...
Page 32: Removal Of Cabinet (L) Block
(M2x3) Screw (M2x3) FP-632 flexible board (VC side)CN151, 8P (SE side)CN909, 8P VL-16 board Except CCD-TR57 Screw (M2x3) 2-9. REMOVAL OF CONTROL SWITCH BLOCK 2-11. REMOVAL OF DD-105 AND PJ-81 BOARDS (FK-8500) Three screws (M2x3) FP-622 flexible board CN932, 16P...
Page 33: Removal Of Vc-195 And Se-65 Board
2-12. REMOVAL OF VC-195 AND SE-65 BOARDS FP-629 flexible board FP-220 flexible board CN903, 23P Flexible board CN105, 8P from loading motor !¡ CN101, 16P Screw (M2x3) from video head FP-621 flexible board CN902, 12P Flexible board CN104, 10P from drum motor FP-620 flexible board (VC side) CN904, 10P (SE side) CN650, 10P...
Page 34: Circuit Board Location
(STEREO MIC, LASER LINK) DD-105 (POWER) PJ-81 (AV IN/OUT) VF-120 (COLOR EVF) LB-54 (BACK LIGHT) VL-16 (EXCEPT CCD-TR57) (VIDEO LIGHT) VC-195 SE-65 (EXCEPT CCD-TR57/TR67/TR413PK) CAMERA, Y/C PROCESSOR, IN/OUT, (STEADY SHOT) REC.PB HEAD AMP, SERVO/SYSTEM CONTROL, SERVO, AUDIO, IR TRANSMITTER, MODE CONTROL...
Page 35: Block Diagrams
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM...
Page 36: Camera/Video 1 Block Diagram
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK 3-2. CAMERA/VIDEO 1 BLOCK DIAGRAM...
Page 37: Vtr/Camera Control Block Diagram
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK 3-3. VTR/CAMERA CONTROL BLOCK DIAGRAM 1.7Vp-p 20 MHz IC402 3Vp-p 13usec IC402 3Vp-p IC402 3Vp-p IC402 3Vp-p IC402 3-11 3-10...
Page 38: Servo Block Diagram
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK 3-4. SERVO BLOCK DIAGRAM 3Vp-p 13usec 3Vp-p IC402 0.76Vp-p 2.8msec 506 kHz IC402 IC801 1.2Vp-p 5.6msec IC451 3Vp-p 3Vp-p 1.2msec 0.76Vp-p IC402 507 kHz IC402 IC801 3Vp-p 13usec IC402 3-12 3-13 3-14...
Page 39: Mode Control Block Diagram
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK 3-5. MODE CONTROL BLOCK DIAGRAM 1.5Vp-p 20 MHz IC604 2.6Vp-p 32 kHz IC604 3-15 3-16 3-17 3-18...
Page 40: Audio Block Diagram
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK 3-6. AUDIO BLOCK DIAGRAM 0.5Vp-p 0.7Vp-p 0.09usec IC751 IC751 0.4Vp-p 0.34Vp-p IC301 0.09usec IC751 0.5Vp-p 2usec IC751 0.25Vp-p 3.58 MHz IC751 CAMERA REC 0.36Vp-p IC301 CAMERA REC 0.26Vp-p 3.58 MHz IC301 CAMERA REC 2.9Vp-p IC301 3-19 3-20 3-21 3-22...
Page 41: Color Evf Block Diagram
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK 3-7. COLOR EVF BLOCK DIAGRAM 7.5Vp-p 7.2Vp-p IC5401 IC5401 7.6Vp-p IC5401 3Vp-p IC5401 3Vp-p 12Vp-p IC5404 IC5301 3Vp-p IC5404 3.4Vp-p 1.84 MHz IC5404 23 24 3Vp-p 7.852 kHz IC5404 20 21 3Vp-p 2.7Vp-p 11.06 MHz IC5404 IC5404 2.4Vp-p...
Page 42: Power Block Diagram
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK 3-8. POWER BLOCK DIAGRAM 3-27 3-28 3-29 3-30 E...
Page 43: Frame Schematic Diagram
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM FRAME...
Page 44 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS CD-181 (CCD IMAGER) PRINTED WIRING BOARD – Ref No. CD-181 BOARD: 3,000 series – THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
Page 45 VF-120 LB-54 (COLOR EVF) (BACK LIGHT) 12 22 1-668-932- VL-16 (EXCEPT CCD-TR57) (VIDEO LIGHT) • For Printed Wiring Boards. There are few cases that the part isn't mounted in this model is printed on this diagram. VC-195 • Chip diode CAMERA, Y/C PROCESSOR, IN/OUT, REC.PB HEAD AMP, SERVO/SYSTEM CONTROL,...
Page 46 There are few cases that the part isn't mounted in this model is printed on this diagram. • Chip transistor • Chip diode VF-120 (COLOR EVF) LB-54 (BACK LIGHT) VL-16 (EXCEPT CCD-TR57) (VIDEO LIGHT) VC-195 11 21 1-668-928- CAMERA, Y/C PROCESSOR, IN/OUT, SE-65 (EXCEPT TR57/TR67/TR413PK) REC.PB HEAD AMP, SERVO/SYSTEM CONTROL,...
Page 47 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK VC-195 BOARD (SIDE A) VC-195 BOARD (SIDE A) C001 A-13 C328 C-11 CN908 A-17 R074 C-12 R527 B-17 C004 A-14 C330 C-11 CN909 G-11 R075 C-13 R529 E-12 C004 B-13 C331 C-11 CN911 D-17 R081 D-13 R551 G-11...
Page 48 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK • For schematic diagrams. • Refer to page 4–13 for Printed Wiring Board. VC-195 BOARD (1/10) CAMERA REC 2.3Vp-p 28.636 MHz IC501 CAMERA REC 2.3Vp-p 14.32 MHz IC501 11 12 CAMERA REC 7Vp-p IC501 CAMERA REC 7Vp-p IC501...
Page 49 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK • For schematic diagrams. • Refer to page 4–13 for Printed Wiring Board. 4-21 4-22 4-23 4-24 CAMERA (2) VC-195 (2/10)
Page 50 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK • For schematic diagrams. • Refer to page 4–13 for Printed Wiring Board. VC-195 BOARD (3/10) CAMERA REC CAMERA REC 0.34Vp-p 3.1Vp-p 3.58 MHz IC202 IC202 CAMERA REC CAMERA REC 0.84Vp-p 3Vp-p IC202 IC202 CAMERA REC CAMERA REC 0.5Vp-p...
Page 51 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK • For schematic diagrams. • Refer to page 4–13 for Printed Wiring Board. VC-195 BOARD (4/10) CAMERA REC 0.46Vp-p IC151 0.32Vp-p IC151 1.4Vp-p IC151 17 64 1.8Vp-p IC151 25 60 IC151 (2.1Vp-p) IC151 (1.6Vp-p) 4-31 4-32 4-29 4-30 IN/OUT...
Page 52 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK • For schematic diagrams. • Refer to page 4–13 for Printed Wiring Board. VC-195 BOARD (5/10) CAMERA REC 0.3Vp-p IC001 CAMERA REC 0.3Vp-p IC001 TRIG : IC001 0.4Vp-p IC001 0.4Vp-p IC001 0.4Vp-p IC001 CAMERA REC 2.9Vp-p IC001 CAMERA REC...
Page 53 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK • For schematic diagrams. • Refer to page 4–13 for Printed Wiring Board. VC-195 BOARD (6/10) CAMERA REC 1.7Vp-p 20 MHz IC402 3Vp-p IC402 3Vp-p IC402 3Vp-p IC402 3Vp-p 13usec IC402 3Vp-p 13usec IC402 3Vp-p 13usec IC402 3Vp-p 1.2msec...
Page 54 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK • For schematic diagrams. • Refer to page 4–13 for Printed Wiring Board. 4-40 4-41 4-42 SERVO VC-195 (7/10)
Page 55 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK • For schematic diagrams. VC-195 BOARD (7/10) • Refer to page 4–13 for Printed Wiring Board. CAMERA REC VC-195 BOARD (8/10) CAMERA REC 1.2Vp-p 2.9Vp-p 5.6msec IC451 IC301 3Vp-p 0.4Vp-p IC451 IC301 CAMERA REC 3Vp-p 0.36Vp-p 2.8msec IC451 IC301 CAMERA REC 0.26Vp-p...
Page 56 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK • For schematic diagrams. • Refer to page 4–13 for Printed Wiring Board. VC-195 BOARD (9/10) VC-195 BOARD (10/10) 1.5Vp-p 0.25Vp-p 20 MHz IC604 3.58 MHz IC751 2.6Vp-p 0.5Vp-p 32 kHz IC604 2usec IC751 0.34Vp-p 0.09usec IC751 0.7Vp-p 0.09usec...
Page 57 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK • For schematic diagrams. • Refer to page 4–13 for Printed Wiring Board. 4-53 4-51 4-52 MODE CONTROL VC-195 (10/10)
Page 58: Control Switch Block (Fk-8500/Ss-8500)
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK MA-311 (STEREO MIC, LASER LINK) PRINTED WIRING BOARDS – Ref No. MA-311 BOARD: 3,000 series – MA-311 BOARD (SIDE B) MA-311 BOARD (SIDE A) 1-668-934- 12 22 MA-311 BOARD Q301 R327 R356 C301 C344 C373 • For Printed Wiring Boards.
Page 59 (COLOR EVF) LB-54 (BACK LIGHT) There are few cases that the part isn't mounted in this model is printed on this diagram. VL-16 (EXCEPT CCD-TR57) (VIDEO LIGHT) • Chip transistor VC-195 CAMERA, Y/C PROCESSOR, IN/OUT, REC.PB HEAD AMP, SERVO/SYSTEM CONTROL,...
Page 60 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CF-49 (CONTROL) PRINTED WIRING BOARD – Ref No. CF-49 BOARD: 3,000 series – CF-49 BOARD (SIDE A) CF-49 BOARD (SIDE B) CF-49 BOARD BH001 B-18 R016 R019 B-11 BZ001 B-15 R020 BZ002 B-15 R022 R023 C001 R025 C002 R026...
Page 61 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CF-49 BOARD CAMERA REC 2.9Vp-p 24.48 kHz IC001 4-67 4-65 4-66 CONTROL CF-49...
Page 62 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK PJ-81 (AV IN/OUT) PRINTED WIRING BOARD – Ref No. PJ-81 BOARD: 3,000 series – PJ-81 BOARD (SIDE B) PJ-81 BOARD C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 CN101 D101 D102 D103 D105 D106 D107 J101...
Page 63 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK VF-119 (COLOR EVF (COLOR EVF MODEL) PRINTED WIRING BOARD VF-119 BOARD – Ref No. VF-119 BOARD: 10,000 series – CAMERA REC VF-119 BOARD (SIDE B) VF-119 BOARD (SIDE A) 3Vp-p IC5401 7.2Vp-p IC5401 7.5Vp-p IC5401 7.6Vp-p IC5401 3Vp-p 1-668-942-...
Page 64 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK VF-120 BOARD CAMERA REC 2.4Vp-p IC5301 12Vp-p IC5301 4-75 4-76 4-77 4-78 COLOR EVF, BACK LIGHT VF-120 LB-54...
Page 65 C5353 C5354 C5355 C5356 VF-120 CN5351 (COLOR EVF) LB-54 D5351 (BACK LIGHT) L5351 L5352 VL-16 (EXCEPT CCD-TR57) ND5351 (VIDEO LIGHT) Q5351 R5351 T5351 1-668-944- VC-195 CAMERA, Y/C PROCESSOR, IN/OUT, REC.PB HEAD AMP, SERVO/SYSTEM CONTROL, SE-65 (EXCEPT TR57/TR67/TR413PK) (STEADY SHOT) SERVO, AUDIO, IR TRANSMITTER, MODE CONTROL...
Page 66 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK DD-105 (POWER) PRINTED WIRING BOARD – Ref No. DD-105 BOARD: 2,000 series – DD-105 BOARD (SIDE B) DD-105 BOARD (SIDE A) DD-105 BOARD C801 L801 R823 C802 L802 R824 C803 L803 R825 C804 L804 R826 C805 L805 R827...
Page 67 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK DD-105 BOARD CAMERA REC 0.76Vp-p 507 kHz IC801 0.76Vp-p 506 kHz IC801 4-85 4-86 4-87 4-88 POWER DD-105...
Page 68: Adjustments
CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK SECTION 5 ADJUSTMENTS Refer to page 3 as Table for distinction functions of models and classification 5-1. CAMERA SECTION ADJUSTMENTS 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Adjusting driver •...
Page 69 J-10 J-11 J-12 J-13 Fig. 5-1-1.
Page 70: Preparations
5-1. CAMERA SECTION ADJUSTMENT 1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. 1) Connect the equipment for adjustments according to Fig. 5-1-3. 2) By setting the “Forced Camera Power ON mode”, the camera power can be turned ON even if the front panel block (MA-311 board, power switch, microphone unit) has been removed.
Page 71 Color monitor Vector scope Terminated at 75 Ω Lens block CD-181 board Regulaterd power supply CN401 (8.4 ± 0.1 Vdc) Battery terminal (Note 1) Extension cable(16P) (J-6082-357-A) Adjusting Need not connected remote VIDEO terminal commander LANC CN935 CN909 terminal CN551 CN912 CN932 CN501...
Page 72: Setting The Switch
1-1-3.Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. 1. POWER switch (MA-311 board) ......CAMERA 6. STEADY SHOT (Menu display) ........OFF 2. NIGHT SHOT switch (Lens block) ........ OFF 7.
Page 73: Adjusting Remote Commander
1-1-4. Adjusting Remote Commander • Changing the address The adjusting remote commander is used for changing the The address increases when the FF ()) button is pressed, calculation coefficient in signal processing, EVR data, etc. The and decreases when the REW (0) button is pressed. There adjusting remote commander performs bi-directional are altogether 256 addresses, from 00 to FF.
Page 74: Data Processing
1-1-5. Data Processing The calculation of the DDS display and the adjusting remote calculate and convert the result to hexadecimal notation, and use it commander display data (hexadecimal notation) are required for as the adjustment data. Table 5-1-2. indicates the hexadecimal obtaining the adjustment data of some adjustment items.
Page 75: Initialization Of D, E, F
1-2. INITIALIZATION OF D, E, F PAGE DATA 2. Modification of D, E, F Page Data If the D, E, F page data has been initialized, change the data of the 1. Initializing the D,E,F Page Data “Fixed data-2” address shown in the following tables by manual Note 1: If “Initializing the D, E, F Page Data”...
Page 76 3. D Page Table Note1 : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Address Initial Value Remark Address Initial Value Remark 00 to 0F Fixed data-1 Fixed data-1...
Page 77 Y OUT level adj. according to the model. AFC f0 adj. Hi8 model : CCD-TR917/ TR940/ TR940PK C OUT level adj. Standard8 model : CCD-TR57/ TR67/ TR87/ TR413PK/ Fixed data-1 TR414PK Filter f0 adj. RP filter f0 adj. Address...
Page 78 Address Initial Value Remark Address Initial Value Remark Switching position adj. Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-2 Fixed data-1 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-2 Fixed data-1 Fixed data-1...
Page 79 5. E Page Table Address Initial Value Remark Note 1: Fixed data-2 Fixed data-1 : Initialized data. ( Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. Fixed data-1 (Refer to “2. Modification of D, E, F Page Data”). Address Initial Value Remark Fixed data-1...
Page 80 Address Initial Value Remark Address Initial Value Remark Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 FC to FF Fixed data-1 VCO adj.
Page 81: Camera System Adjustments
1-3. CAMERA SYSTEM ADJUSTMENTS 2. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain Before perform the camera system adjustments, Check that the and offset. specified value of “28MHz Origin Oscillation Adjustment”, “Y OUT level Adjustment”...
Page 82: Flange Back Adjustment
22) Read the DDS display data, and this data is named K . If K lies 3. Flange Back Adjustment within the “19” to “1D” range, perform “Processing after The inner focus lens flange back adjustment is carried out completing adjustments”. If it is lies outside the range, perform automatically.
Page 83: Flange Back Adjustment (1)
3-2. Flange Back Adjustment (2) 4. Flange Back Check Perform this adjustment after performing “Flange Back Adjustment Subject Siemens star (1)”. (2.0 m from the front of the lens) (Luminance: approx. 200 lux) Subject Subject more than 500m away Measurement Point Check operation on TV monitor (Subjects with clear contrast such as Measuring Instrument...
Page 84: Picture Frame Setting
5. Picture Frame Setting 1. Horizontal period Subject Color bar chart standard picture frame (1.5m from the front of the lens) Measurement Point Video output terminal Measuring Instrument Oscilloscope and TV monitor A=B, C=D, t=0 ± 0.1msec Specified Value Setting method: 1) Adjust the zoom and the camera direction, and set to the specified position.
Page 85: Color Reproduction Adjustment
Adjustment Page Adjustment Address 34, 36, F5, F6 Specified Value All color luminance points should settle within each color reproduction frame. Note1: 510H model (CCD-TR57/TR67/TR413PK) 760H model (CCD-TR87/TR414PK/TR917/TR940/ TR940PK) Switch setting: 1) NIGHT SHOT switch ............OFF Adjusting method: Burst positon 1) Select page: 0, address: 01, and set data: 01.
Page 86: Iris In/Out Adjustment
00 00 XX 00 XX XX n Object data n Lower two digits n Upper two digits Note 2: 510H model : CCD-TR57/TR67/TR413PK Switch setting: 760H model : CCD-TR87/TR414PK/TR917/TR940/ 1) STEADY SHOT (Menu display) ........OFF TR940PK 2) NIGHT SHOT switch ............OFF Switch setting: 1) STEADY SHOT (Menu display) ........
Page 87: Auto White Balance Standard Data Input
9. Auto White Balance Standard Data Input 10. Auto White Balance Adjustment Adjust to the proper auto white balance output data. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color bar standard picture frame) be poor.
Page 88: White Balance Check
11. White Balance Check Subject Clear chart (Color bar standard picture frame) Filter Filter C14 for color temperature correction ND filter 1.0 and 0.3 2 mm Measurement Point video output terminal Measuring Instrument Vectorscope Specified Value Fig. 5-1-10. A to C Switch setting: 1) NIGHT SHOT switch ............
Page 89: Angular Velocity Sensor Sensitivity Adjustment
12. Angular Velocity Sensor Sensitivity Adjustment • This adjustment is performed only when replacing the angular velocity sensor. Although this adjustment need not be performed when the circuit is damaged, etc., check the operations. • Note down the sensitivity displayed on the angular velocity sensor of the repair parts.
Page 90: Color Electronic Viewfinder System Adjustments
1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM 1. EVF Initial Data Input ADJUSTMENT Mode VTR stop Note 1: The back light (fluorescent tube) is driven by a high voltage Signal No signal AC power supply. Therefore, do not touch the back light Adjustment Page holder to avoid electrical shock.
Page 91: Vco Adjustment (Vf-119 Board)
2. VCO Adjustment (VF-119 board) 3. Bright Adjustment (VF-119 board) Set the VCO free-run frequency. If deviated, the EVF screen will be Set the level of the VIDEO signal for driving the LCD to the specified blurred. value. If deviated, the screen image will be blackish or saturated (whitish).
Page 92: Contrast Adjustment (Vf-119 Board)
4. Contrast Adjustment (VF-119 board) 5. Backlight Consumption Current Adjustment (VF-120 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated Set the backlight luminance and color temperature. (whitish).
Page 93: Mechanical Section Adjustment
5-2. MECHANICAL SECTION ADJUSTMENT 2-2. TAPE PATH ADJUSTMENT 1. Preparations for adjustments Mechanism Parts Adjustments 1) Clean the tape path face (tape guide, drum, capstan shaft, pinch roller). For details on the adjustments and checks of mechanical section 2) Connect the adjusting remote commander to the LANC terminal. and replacements of mechanism parts, refer to the separate volume- 3) Turn on the HOLD switch of the adjusting remote commander.
Page 94: Video Section Adjustments
5-3. VIDEO SECTION ADJUSTMENTS When performing adjustments, refer to the layout diagrams for adjustment related parts beginning from page 5-52. 3-1. PREPARATIONS BEFORE ADJUSTMENT The following adjusting instruments are used for adjusting the video section. 3-1-1. Equipments to be Used 12) Remote commander for adjustment (J-6082-053-B) 1) TV monitor 2) Oscilloscope: 2 phenomena, band 30 MHz or wider, with delay...
Page 95: Precautions In Adjusting
3-1-2. Precautions on Adjusting 3-1-3. Adjusting Connectors 1) The adjustments of this unit are performed in the VTR mode or Some of the adjusting points of the video section are concentrated camera mode. at VC-195 board CN910. Connect the measuring instruments via To set to the VTR mode, set the power switch to “VTR”...
Page 96: Connecting The Equipments
3-1-4. Connecting the Equipments Connect the measuring instruments as shown in Fig. 5-3-2 and perform the adjustments. Connecting the TV Monitor and Regulated Power Supply Battery terminal Main Unit TV monitor Regulated power supply 8.4 ± 0.1Vdc VIDEO Connect when using the camera mode or playing back.
Page 97: Input/Output Level And Impedance
3-1-6. Input/Output Level and Impedance 3-1-8. Service Mode Video input/output Additional note on adjustment Phono jack, 1 Vp-p, 75Ω, Note: After the completion of the all adjustments, cancell the unbalanced, sync negative service mode by either of the following ways. S video input/output (Hi8 model) 4-pin mini DIN 1) Unplug the main power supply and remove the lithium battery.
Page 98: Emergency Memory Address
2. Emergency Memory Address 2-1. EMG CODE (Emergency Code) The codes shown in the following table which correspond to errors Page F Address 10 to 1B that occur are recorded in addresses 10, 14, and 18. Address Contents Code Type of Emergency 1st EMG code No error Upper: MSW code when the mechanism starts shifting...
Page 99: Msw Codes
2-2. MSW Codes • The lower parts of the data of addresses 12, 16 and 1A represent the MSW codes (mode switch, mechanism position) when errors occurs. • The upper parts of the data of addresses 12, 16 and 1A represent, when the mechanism position is to be moved, the MSW codes at the start of movement (when moving the loading motor).
Page 100: Bit Value Discrimination
3. Bit value discrimination 4. Switch check (1) Bit values must be discriminated using the display data of the Page 3 Address 43 adjusting remote commander for the following items. Use the table below to discriminate if the bit value is “1” or “0”. Function When bit value=1 When bit value=0 0 VTR MODE SW...
Page 101: Switch Check (2)
5. Switch check (2) Page 3 Address 60 to 65 Using method: 1) Select page: 3, address: 60 to 65. 2) By discriminating the display data, the pressed key can be discriminated. Data Address 00 to 0D 0E to 29 2A to 46 47 to 68 69 to 90...
Page 102: Led, Lcd (Display Window) Check
8. LED, LCD (display window) check 9. Record of Use Check Page 3 Address 05 Bit5 Page 3 Address A2 to AA Address Using method: Function Remarks 1) Select page: 3, address: 05, and set the bit value of Bit5 to “1”. 1000th place digit and 2) Check that all LED are lit and all segments of LCD (display 100th place digit of...
Page 103: System Control System Adjustment
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Initialization of D, E, F Page Data If the D, E, F page data is erased due to some reason, perform “1-2. INITIALIZATION OF D, E, F PAGE DATA”, of “5-1. CAMERA SECTION ADJUSTMENT”. 2.
Page 104: Servo System Adjustments
3-3. SERVO SYSTEM ADJUSTMENTS 2. Switching Position Adjustment (VC-195 Board) If deviated in this case causes switching noise or jitter on the played 1. CAP FG Offset Adjustment (VC-195 board) back screen. Improve the capstan servo characteristic. If it is not correct. jitters Mode Playback will increase.
Page 105: Ntsc Lp Mode Switching Position Adjustment (Vc-195 Board) (Ccd-Tr917/Tr940/Tr940Pk)
3. NTSC LP mode Switching Position Adjustment 3-4. VIDEO SYSTEM ADJUSTMENTS (VC-195 Board) (CCD-TR917/ TR940/ TR940PK) Video system adjustments must be performed in the following order. If deviated in this case causes switching noise or jitter on the LP mode played back screen. [Adjusting Order] 1.
Page 106: Afc F0 Adjustment (Vc-195 Board)
2. AFC f0 Adjustment (VC-195 board) 3. Filter f0 Adjustment (VC-195 board) Adjust the pull-in range of the A/D converted clock generator during Minimize the chroma signal residual components during composite playback. video signal input. Mode VTR stop Mode VTR stop Signal No signal Signal...
Page 107: Y Out Level Adjustment (Vc-195 Board)
4. Y OUT Level Adjustment (VC-195 board) 5. C OUT Level Adjustment (VC-195 board) Set the Y signal output level. Set the chroma signal output level. Mode VTR stop Mode VTR stop Signal No signal Signal No signal Measurement Point Hi8 model : Measurement Point Hi8 model :...
Page 108: Rp Filter F0 Adjustment (Vc-195 Board)
6. RP Filter f0 Adjustment (VC-195 board) 7. Hi8 REC Y Current Adjustment (VC-195 board) (CCD-TR917/TR940/TR940PK) Adjust the LPF of the playback RF amplifier. Adjust the Y FM signal recording current. Mode VTR stop Signal No signal Mode VTR recording (SP mode) Pin 9 of CN910 (RF AGC OUT) Measurement Point Signal...
Page 109: (Ccd-Tr57/Tr67/Tr87/Tr413Pk/Tr414)
8. Standard8 REC Y Current Adjustment (VC-195 board) 10) Write the following data in page: F, address: 57 to 5A. (CCD-TR57/ TR67/ TR87/ TR413PK/ TR414PK) Address Data Adjust the Y FM signal recording current. Mode VTR recording (SP mode) Signal No signal Pin !º...
Page 110: Hi8 Rec L Level Adjustment (Vc-195 Board) (Ccd-Tr917/Tr940/Tr940Pk)
9) Write the following data in page: F, address: 63 to 64. 9. Hi8 REC L Level Adjustment (VC-195 board) (CCD-TR917/TR940/TR940PK) Address Data Set the recording levels of the REC AFM signal and REC ATF signal. If the level is too low, the audio S/N will deteriorated, tracking will not be stable, or SP/LP will not be discriminated properly.
Page 111: (Ccd-Tr57/Tr67/Tr87/Tr413Pk/Tr414Pk)
10. Standard8 REC L Level Adjustment (VC-195 board) 9) Write the following data in page: F, address: 63 to 64. (CCD-TR57/ TR67/TR87/TR413PK/ TR414PK) Address Data Set the recording levels of the REC AFM signal and REC ATF signal. If the level is too low, the audio S/N will deteriorated, tracking will not be stable, or SP/LP will not be discriminated properly.
Page 112: Rec C Current Adjustment (Vc-195 Board)
A = 34.6±1.2mV Standard8 model : A = 30.9±1.1mV Note 1: HI8 model: CCD-TR917/ TR940/ TR940PK Standard8 model: CCD-TR57/ TR67/ TR87/ TR413PK/ TR414PK 1.35 µ sec Connection: 1) Remove C085 (0.01µF, Pin !§ of IC202). Fig. 5-3-17. Note: After completing “REC L Level Adjustment” and “REC C Current Adjustment”, replace C085 with new parts (1-162-...
Page 113: Ir Transmitter Adjustments (Ccd-Tr87/Tr414Pk/Tr917/Tr940/Tr940Pk)
3-5. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (VC-195 board) (CCD-TR87/ TR414PK/ TR917/ TR940/ TR940PK) Mode Camera standby Subject Arbitrary Adjust using a IR receiver jig (J-6082-383-A). Measurement Point VIDEO OUT terminal of IR receiver jig (Terminated at 75Ω) Switch setting: Measuring Instrument Oscilloscope...
Page 114: Ir Audio Deviation Adjustment (Vc-195 Board)
3. IR Audio Deviation Adjustment (VC-195 board) Adjusting method: 1) Select page: 0, address: 01, and set data: 01. Mode VTR recording 2) Connect the audio level meter to the AUDIO L terminal of the Signal Audio signal : IR receiver jig. 400Hz, –7.5dBs : L or R of AUDIO 3) Select page: F, address: 67, change the data and set the 400Hz terminal...
Page 115: Stereo Audio System Adjustment (Ccd-Tr917/Tr940/Tr940Pk)
3-6. STEREO AUDIO SYSTEM ADJUSTMENT [Connecting the measuring instruments for the audio] (CCD-TR917/ TR940/ TR940PK) Connect the audio system measuring instruments in addition to the video system measuring instruments as shown in Fig. 5-3-22, and • Perform the adjustment using the color bar signal as a video perform adjustments at the power switch [VTR] or [PLAYER] signal input for VIDEO terminal.
Page 116 1. 1.5 MHz Deviation Adjustment (VC-195 board) 2. 1.7 MHz Deviation Adjustment (VC-195 board) Sets the spectrum of the L-ch ((L+R)/2 signal) level modulated Sets the spectrum of the R-ch ((L-R)/2 signal) level modulated during during recording. If deviated, the crosstalk signal of the audio signal recording.
Page 117: Bpf F0 Adjustment (Vc-195 Board)
MONAURAL Sets the BPF passing frequency so that the AFM signal can separate from the playback RF signal properly. If deviated. the mono/stereo (CCD-TR57/TR67/TR87/TR413PK/ TR414PK) mode will be differentiated incorrectly, and noises and distortions will increase during high volume playback.
Page 118: Mhz Deviation Adjustment (Vc-195 Board)
1. 1.5 MHz Deviation Adjustment (VC-195 board) 2. BPF Adjustment (VC-195 board) 3-8. ARRANGEMENT DIAGRAM FOR ADJUSTMENT PARTS Adjust to the optimum audio BPF characteristics of the IC. Adjust to the optimum audio FM signal distortion. If the adjustment is not correct, its playback level will differ from If the adjustment is not correct, the distortion rate and S/N ratio will VC-195 BOARD (SIDE A) worsen.
Page 119: Repair Parts List
Les composants identifiés par une 6-1-1. CABINET (L) BLOCK ASSEMBLY marque ! sont critiques pour la sécurité. Ne les remplacer que par une Except CCD-TR57 piéce portant le numéro spécifié. S003 not supplied J001 not supplied...
Page 120: Front Panel Block Assembly (Except Ccd-Tr57)
6-1-2. FRONT PANEL BLOCK ASSEMBLY (EXCEPT CCD-TR57) not supplied not supplied not supplied not supplied MIC901 MIC902 LAMP,HALOGEN CCD- TR917/TR940/ VL901 XB-3D(DC6V/3W) TR940PK Les composants identifiés par une The components identified by marque ! sont critiques pour la mark ! or dotted line with mark ! are critical for safety.
Page 121: Front Panel Block Assembly (Ccd-Tr57)
6-1-3. FRONT PANEL BLOCK ASSEMBLY (CCD-TR57) not supplied not supplied not supplied not supplied MIC901 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3948-189-1 PANEL (870) ASSY, FRONT 3-987-633-01 BUTTON, LOCK A-7073-463-A MA-311(7ZL) BOARD, COMPLETE 3-987-631-01 KNOB, P...
Page 122: Cabinet (R) Block Assembly
6-1-4. CABINET (R) BLOCK ASSEMBLY not supplied CCD-TR917/TR940/TR940PK CCD-TR917/ TR940/TR940PK not supplied LCD901 not supplied CCD-TR87/TR414PK/ TR917/TR940/TR940PK supplied ND801 CCD-TR917/TR940/ TR940PK not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-475-620-11 SWITCH BLOCK, CONTROL(MF-8500) X-3948-393-1 COVER (864D) ASSY, TR (TR917) (TR917/TR940/TR940PK) * 160 3-987-755-01 HOLDER (864), LCD (TR917/TR940/TR940PK)
Page 123: Evf Block Assembly
6-1-5. EVF BLOCK ASSEMBLY not supplied LCD902 not supplied ND5351 Les composants identifiés par une The components identified by mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety. sécurité. Replace only with part number Ne les remplacer que par une specified.
Page 124: Main Boards Block Assembly
6-1-6. MAIN BOARDS BLOCK ASSEMBLY CCD-TR57 not supplied Except CCD-TR57 SE452 SE451 CCD- TR87/TR414PK/TR917/ TR940/TR940PK Be sure to read “Note on the CCD Imager replacement” on page 4–8 when changing the CCD imager. Ref. No. Part No. Description Remark Ref. No.
Page 125: Battery Panel And Lens Block Assembly
6-1-7. BATTERY PANEL AND LENS BLOCK ASSEMBLY IC401 not supplied not supplied not supplied not supplied J901 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-758-133-21 FILTER BLOCK, OPTICAL X-3948-171-1 PANEL ASSY, BATTERY (TR57/TR67/TR413PK/TR414PK) 3-968-729-01 SCREW (M2X3), LOCK ACE, P2 3-987-656-01 LID, JACK 3-978-981-11 ADAPTOR (FK), CCD FITTING 8-848-724-01 DEVICE, LENS, LSV-601A (SOC)
Page 126: Zoom Lens Block Assembly
6-1-8. ZOOM LENS BLOCK ASSEMBLY CCD-TR917/TR940/TR940PK M906 M905 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 8-848-722-01 DEVICE, LENS LSV-600A (SOC) 2-327-405-01 WASHER (TR917/TR940/TR940PK) 2-623-756-21 SCREW (B1.7X5), P 8-848-724-01 DEVICE, LENS LSV-601A (SOC) 3-979-037-11 SPRING, RETURN (TR57/TR67/TR87/TR413PK/TR414PK) M905 1-763-047-11 MOTOR, FOCUS STEPPING...
Page 127: Cassette Compartment Assembly
6-1-9. CASSETTE COMPARTMENT ASSEMBLY LS CHASSIS BLOCK SECTION (See page 6-10) MECHANISM CHASSIS BLOCK SECTION (See page 6-11) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7040-421-A DAMPER ASSY X-3945-399-1 GEAR ASSY, GOOSENECK 7-624-102-04 STOP RING 1.5, TYPE -E 3-947-503-01 SCREW (M1.4X2.5) X-3945-400-X CASSETTE COMPARTMENT ASSY 3-331-007-21 WASHER...
Page 128: Ls Chassis Assembly
6-1-10. LS CHASSIS ASSEMBLY S002 S001 D001 FP-249 (not supplied) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7040-419-A BASE (S) BLOCK ASSY, GUIDE 3-965-563-01 GEAR, T SOFT A-7040-418-B BASE (T) BLOCK ASSY, GUIDE 3-965-559-01 STOPPER (T) 3-965-565-01 CLAW, T SOFT 3-965-557-01 STOPPER (T), GB X-3945-397-1 DECK ASSY, REEL, S...
Page 129: Mechanism Chassis Assembly
6-1-11. MECHANISM CHASSIS ASSEMBLY M901 M903 M902 S901 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3947-343-1 GROUND (IM) ASSY, SHAFT 3-965-542-01 SHIELD, MOTOR 3-965-550-02 SCREW (M1.7X1.6) 3-965-539-01 GEAR (A) 1-657-785-11 FP-248 FLEXIBLE BOARD 3-965-538-01 SLEEVE, MOTOR HOLDER 3-965-545-01 SPACER, CAPSTAN 3-965-549-01 SCREW (M1.4 X 6.5)
Page 130: Electrical Parts List
CD-181 CF-49 6-2. ELECTRICAL PARTS LIST Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by In each case, u: µ , for example: may be different from the parts specified in the mark ! or dotted line with mark uA...: µ...
Page 131 CF-49 DD-105 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R026 1-216-825-11 METAL CHIP 2.2K 1/16W C804 1-107-826-11 CERAMIC CHIP 0.1uF R028 1-216-822-11 METAL CHIP 1.2K 1/16W C805 1-107-826-11 CERAMIC CHIP 0.1uF R029 1-216-828-11 METAL CHIP 3.9K 1/16W R031...
Page 132 DD-105 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D802 8-719-067-36 DIODE MA3ZD1200LS0 ! PS803 1-533-760-21 FUSE (SMD) (1.4A/24V) D803 8-719-067-36 DIODE MA3ZD1200LS0 (TR57/TR67/TR87/TR917/TR940) D804 8-719-067-36 DIODE MA3ZD1200LS0 D805 8-719-067-36 DIODE MA3ZD1200LS0 ! PS803 1-533-761-21 LINK, IC (SMD) (1.4A/24V) (TR413PK/TR414PK/TR940PK) D809 8-719-027-77 DIODE MA796-TX...
Page 133 DD-105 FP-249 FP-355 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R808 1-218-879-11 RES,CHIP 0.50% 1/16W R912 1-218-879-11 RES,CHIP 0.50% 1/16W R809 1-216-813-11 METAL CHIP 1/16W R810 1-216-837-11 METAL CHIP 1/16W R913 1-216-857-11 METAL CHIP 1/16W R916 1-216-864-11 METAL CHIP 1/16W...
Page 134 LB-54 MA-311 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7073-439-A LB-54 BOARD, COMPLETE C306 1-135-259-11 TANTAL. CHIP 10uF 6.3V (EXCEPT TR57) ********************** (Ref. No. 10,000 Series) C321 1-163-809-11 CERAMIC CHIP 0.047uF (EXCEPT TR917/TR940/TR940PK) ! ND5351 1-517-414-51 FLUORESCENT TUBE (0.55 INCH) C322 1-115-467-11 CERAMIC CHIP 0.22uF...
Page 135 (EXCEPT TR57/TR67/TR413PK) D302 8-749-060-65 DIODE DCC3810 R315 1-216-864-11 METAL CHIP 1/16W (EXCEPT TR57/TR67/TR413PK) (EXCEPT TR57/TR67/TR413PK) D303 8-719-061-82 DIODE TLSU1002 (TPX1,SONY) R321 1-216-864-11 METAL CHIP 1/16W D305 8-719-404-49 DIODE MA111-TX (EXCEPT TR57) (TR917/TR940/TR940PK) D321 8-719-420-14 DIODE MA8082-TX (TR917/TR940/TR940PK) Les composants identifiés par une...
Page 136 MA-311 PJ-81 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R322 1-216-864-11 METAL CHIP 1/16W R354 1-216-829-11 METAL CHIP 4.7K 1/16W R323 1-216-864-11 METAL CHIP 1/16W (TR917/TR940/TR940PK) R324 1-216-864-11 METAL CHIP 1/16W (TR917/TR940/TR940PK) R355 1-216-833-11 METAL CHIP 1/16W (TR917/TR940/TR940PK) R325...
Page 137 SE-65 VC-195 PJ-81 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D105 8-719-059-57 DIODE MAZJ082DFLSO C466 1-162-970-11 CERAMIC CHIP 0.01uF (TR917/TR940/TR940PK) D106 8-719-059-57 DIODE MAZJ082DFLSO < CONNECTOR > (TR917/TR940/TR940PK) CN451 1-691-348-11 CONNECTOR, FFC/FPC (ZIF) 10P < JACK > <...
Page 138 VC-195 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C008 1-162-927-11 CERAMIC CHIP 100PF C070 1-162-908-11 CERAMIC CHIP 0.25PF 50V C009 1-164-217-11 CERAMIC CHIP 150PF C071 1-104-752-11 TANTAL. CHIP 33uF 6.3V C010 1-162-970-11 CERAMIC CHIP 0.01uF C072 1-162-958-11 CERAMIC CHIP 270PF...
Page 139 VC-195 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C173 1-164-227-11 CERAMIC CHIP 0.022uF C243 1-115-156-11 CERAMIC CHIP (TR917/TR940/TR940PK) (TR917/TR940/TR940PK) C244 1-115-156-11 CERAMIC CHIP C174 1-164-217-11 CERAMIC CHIP 150PF (TR917/TR940/TR940PK) (TR917/TR940/TR940PK) C175 1-162-964-11 CERAMIC CHIP 0.001uF C245 1-162-970-11 CERAMIC CHIP 0.01uF...
Page 140 VC-195 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C346 1-162-970-11 CERAMIC CHIP 0.01uF C506 1-115-156-11 CERAMIC CHIP C347 1-162-970-11 CERAMIC CHIP 0.01uF C507 1-115-156-11 CERAMIC CHIP C349 1-162-970-11 CERAMIC CHIP 0.01uF C508 1-162-970-11 CERAMIC CHIP 0.01uF C371 1-104-908-11 TANTAL.
Page 141 VC-195 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C618 1-162-970-11 CERAMIC CHIP 0.01uF C773 1-162-922-11 CERAMIC CHIP 39PF C619 1-162-970-11 CERAMIC CHIP 0.01uF (EXCEPT TR57/TR67/TR413PK) C774 1-109-982-11 CERAMIC CHIP C620 1-162-970-11 CERAMIC CHIP 0.01uF (EXCEPT TR57/TR67/TR413PK) C621 1-162-970-11 CERAMIC CHIP 0.01uF...
Page 142 VC-195 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FB204 1-414-228-11 INDUCTOR CHIP 0UH L154 1-414-754-11 INDUCTOR 10uH (TR917/TR940/TR940PK) L155 1-414-754-11 INDUCTOR 10uH FB205 1-414-228-11 INDUCTOR CHIP 0UH L156 1-414-754-11 INDUCTOR 10uH (TR917/TR940/TR940PK) L201 1-414-754-11 INDUCTOR 10uH FB206 1-414-228-11 INDUCTOR CHIP 0UH L202...
Page 143 VC-195 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q026 8-729-031-69 TRANSISTOR 2SA1965-TL Q552 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO (TR917/TR940/TR940PK) Q553 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q027 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO Q028 8-729-037-74 TRANSISTOR UN9213J-(K8).SO Q607 8-729-041-43 TRANSISTOR HN1L02FU(TE85R) Q029 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO Q609 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q030...
Page 144 VC-195 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R043 1-216-833-11 METAL CHIP 1/16W R093 1-216-833-11 METAL CHIP 1/16W (TR917/TR940/TR940PK) R045 1-216-845-11 METAL CHIP 100K 1/16W R094 1-216-815-11 METAL CHIP 1/16W R046 1-216-821-11 METAL CHIP 1/16W (TR917/TR940/TR940PK) R047 1-216-864-11 METAL CHIP...
Page 145 VC-195 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R217 1-216-864-11 METAL CHIP 1/16W R319 1-216-845-11 METAL CHIP 100K 1/16W (EXCEPT TR917/TR940/TR940PK) (TR917/TR940/TR940PK) R218 1-216-826-11 METAL CHIP 2.7K 1/16W R320 1-216-849-11 METAL CHIP 220K 1/16W R219 1-216-826-11 METAL CHIP 2.7K 1/16W...
Page 146 VC-195 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R456 1-216-833-11 METAL CHIP 1/16W R557 1-216-843-11 METAL CHIP 1/16W R457 1-216-833-11 METAL CHIP 1/16W R558 1-216-295-91 SHORT R458 1-216-808-11 METAL CHIP 1/16W R560 1-216-821-11 METAL CHIP 1/16W R459 1-216-864-11 METAL CHIP...
Page 147 VC-195 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R646 1-216-853-11 METAL CHIP 470K 1/16W R759 1-216-833-11 METAL CHIP 1/16W (EXCEPT TR57/TR67/TR413PK) R647 1-216-853-11 METAL CHIP 470K 1/16W R760 1-216-835-11 METAL CHIP 1/16W R648 1-216-853-11 METAL CHIP 470K 1/16W (EXCEPT TR57/TR67/TR413PK)
Page 148 VF-119 VF-120 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7073-437-A VF-119 BOARD, COMPLETE R5420 1-216-843-11 METAL CHIP 1/16W R5421 1-216-839-11 METAL CHIP 1/16W ********************** (Ref. No. 10,000 Series) R5422 1-216-840-11 METAL CHIP 1/16W < CAPACITOR > R5423 1-216-853-11 METAL CHIP 470K...
Page 149 VF-120 VL-16 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > MISCELLANEOUS ************* IC5301 8-759-097-75 IC MB3789PFV-G-BND 1-475-619-11 SWITCH BLOCK, CONTROL (SS-8500) < COIL > 1-475-617-11 SWITCH BLOCK, CONTROL (FK-8500) (TR57/TR67/TR413PK) L5301 1-412-031-11 INDUCTOR CHIP 47uH 1-475-617-21 SWITCH BLOCK, CONTROL (FK-8500) (TR87TR414PK) <...
Page 150 Ref. No. Part No. Description Remark ! ND5351 1-517-414-51 FLUORESCENT TUBE (0.55 INCH) S001 1-692-614-11 SWITCH, PUSH (3 KEY) (Hi8 MP, ME/MP, REC PROOF) S002 1-572-688-11 SWITCH, PUSH (1 KEY)(C.C. LOCK) S003 1-572-688-11 SWITCH, PUSH (EJECT) S901 1-762-436-15 SWITCH, ROTARY (ENCODER) SE451 1-803-041-11 SENSOR, ANGULAR VELOCITY (YAW) (TR87/TR414PK/TR917/TR940/TR940PK)
Page 151 S I D E B CN909 CN551 I C 2 0 4 C N 9 0 7 C N 9 1 0 VC-195 BOARD CN914 IC402 C N 9 0 4 I C 4 5 1 IC301 SIDE A CCD-TR57/TR67/TR87/TR413PK/TR414PK/ TR917/TR940/TR940PK...
Page 152 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT Take a copy CAMERA COLOR REPRODUCTION FRAME and Parts reference sheets with a clear sheet for use. For 510H model CCD-TR57/TR67/TR413PK For 760H model CCD-TR87/TR414PK/TR917/TR940/TR940PK...
Page 153 CCD-TR57/TR67/TR87/TR413PK/TR414PK/TR917/TR940/TR940PK Sony Corporation 98A0929-1 Printed in Japan © 1998. 1 9-974-035-11 Personal A&V Products Company Published by Quality Engineering Dept. – 246 – (Osaki East)

This manual is also suitable for:

Handycam ccd-tr87 Handycam ccd-tr917 Handycam ccd-tr940 Handycam ccd-tr940pk Handycam ccd-tr67 Handycam ccd-tr413pk ... Show all

Sony Handycam CCD-TR57 Service Manual

Service Note

Self-Diagnosis Function

Disassembly

Block Diagrams

4 Printed Wiring Boards and Schematic

Adjustments

Repair Parts List

Quick Links

Related Manuals for Sony Handycam CCD-TR57

Summary of Contents for Sony Handycam CCD-TR57

This manual is also suitable for:

Table of Contents