Page 1 Helical scanning FM system On-screen display Electronic viewfinder Illumination range TN LCD/TFT active matrix method Audio recording system CCD-TR315/TRV series : Monochrome 0.4 lux to 100,000 lux Rotary heads, FM system Total dot number CCD-TR416/TR416PK/TR516/ Recommended illumination 61,380 (279 x 220)
Page 2: Camera Recording
Averege power consumption(when Mass (Approx.) Input and output connectors AC power adaptor using the battery pack) CCD-TR315/TR716 : 1 lb 11 oz (790 g) Video output Power requirements During camera recording CCD-TR416/TR416PK/TR516/ Phono jack, 1 Vp-p, 75 ohms, unbalanced 100 -240 V AC, 50/60 Hz...
Page 3 Table for difference of function Model CCD- CCD- CCD- CCD- CCD- CCD- CCD- CCD- CCD- CCD- Remark TR315 TR416 TR416PK TR516 TR516PK TR716 TRV16 TRV16PK TRV36 TRV36PK Destination E,BR US,CND US,CND US,CND US,CND,E, US,CND HK,BR,TW Classification TYPE E TYPE G TYPE C TYPE D TYPE F...
Page 4 Supplied accessories 1 RMT-708 Wireless Remote Commander (1) 7 Shoulder strap (1) CCD-TR516/TR516PK/TR716 8 Video P6-15P HB tape CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR416: US/TR516: US/TR716:US 2 AC-L10A/L10B/L10C AC power adaptor CCD-TRV16:US/TRV36:US/TRV43:US/TRV46:US 3 NP-F330 Battery pack (1) 9 2 pin conversion adaptor (1) CCD- TR315//TR416PK/TR516PK 4 CR2025 Lithium Battery (1) CCD- TRV16:E,BR,HK,TW/TRV16PK/TRV36PK/ TRV46:E,HK/TRV46PK...
Page 5: To Take Out A Cassette When Not Eject (Force Eject)
SERVICE NOTE 1. POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. Battery switch This following three methods are available to prevent this.
Page 6: Self-Diagnosis Function
SELF-DIAGNOSIS FUNCTION 1. Self-diagnosis Function 2. Self-diagnosis display When problems occur while the unit is operating, the self-diagno- When problems occur while the unit is operating, the counter of the sis function starts working, and displays on the viewfinder or Dis- viewfinder or Display window shows a 4-digit display consisting play window what to do.
Page 7: Self-Diagnosis Code Table
4. Self-diagnosis Code Table Self-diagnosis Code Symptom/State Correction Block Detailed Function Code Remove the cassette, and insert it again after one hour. Condensation. Video head is dirty. Clean with the optional cleaning cassette. Non-standard battery is used. Use the InfoLITHIUM battery. LOAD direction.
Page 8: Table Of Contents
TABLE OF CONTENTS SERVICE NOTE 2. DISASSEMBLY 1. Power Supply During Repairs ..........5 2-1. Removal of Front Panel Block and Video Light Block ..2-1 2. To Take out a Cassette when not Eject (Force Eject) ....5 2-2. Removal of LB-54, VF-119 and VF-120 Boards (Color View Finder Models) ....
Page 9 4. PRINTED WIRING BOARDS AND SCHEMATIC 5. ADJUSTMENTS DIAGRAMS 5-1. CAMERA SECTION ADJUSTMENTS ......5-1 1-1. Preparations before Adjustment (Camera Section) ..5-1 4-1. Frame Schematic Diagram (1) ........... 4-1 1-1-1. List of Service Tools ..........5-1 • Frame Schematic Diagram (2) ........4-4 1-1-2.
Page 10 Switch check (2) ............5-43 6-1-8. B/W EVF Block Assembly Headphone jack check ..........5-43 (CCD-TR315 and TRV series) ......... 6-8 Input/output selection check ........5-43 6-1-9. LCD Block Assembly (TRV series) ......6-9 LED, LCD (display window) check ......5-44 6-1-10.
Page 11: General
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK This section is extracted SECTION 1 from instruction manual of GENERAL CCD-TRV36/TRV43/TRV46.
Page 20 1-10...
Page 21 1-11...
Page 22 1-12...
Page 23 1-13...
Page 24 1-14...
Page 25 1-15...
Page 26 1-16...
Page 27 1-17...
Page 28 1-18...
Page 29 1-19...
Page 30 1-20E...
Page 31: Disassembly
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 2 DISASSEMBLY The equipment can be removed using the following procedure. VIDEO CAMERA RECORDER 2-1. FRONT PANEL BLOCK 2-2. LB-54/VF-119 & 120 BOARDS 2-5. CASSETTE LID ASSEMBLY (Color view finder models only) VIDEO LIGHT BLOCK 2-3. CRT/VF-99 BOARD...
Page 32: Removal Of Lb-54, Vf-119 And Vf-120 Boards (Color View Finder Models)
VF-120 board VF light interception sheet 2-3. REMOVAL OF VF-99 AND CRT ASSEMBLY (B/W view finder model CCD-TR315 and TRV series Tilt-up the EVF block to the direction of arrow A . CRT assembly CRT holder assmebly Remove the EVF rear cabinet assembly to the direction of arrow B .
Page 33: Removal Of Cabinet (R) Block
2-4. REMOVAL OF CABINET (R) BLOCK Note : Be sure to that the pin of the Lens assembly is put into the hole of the IR knob when attaching. (TR series) (TRV series) Flat cable (FFC-257F) Flat cable (FFC-257F) CN911, 45P CN911, 45P Two screws Two screws...
Page 34: Removal Of Cabinet (L) Block
2-9. REMOVAL OF ZOOM LENS BLOCK AND 2-10. REMOVAL OF DD-117 AND PJ-90/91 BOARDS VL-21/22 BOARD Three screws (M2 x 3) —Video light models— CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK —No video light models— CCD-TR315/TR416/TR416PK CN931, 70P FP-621 flexible board CCD-TRV16/TRV16PK CN101, 12P Two screws (M2 x 3) Shoe bracket...
Page 35: Removal Of Vc-215 Abd Se-80/81 Boards
CN908, 15P !£ SE-80/81 board CCD-TR716 & TRV series 2-12. REMOVAL OF VIEW FINDER BLOCK —Color view finder— —B/W view finder— CCD-TR315 and TRV series CCD-TR416/TR416PK/TR516/TR516PK/TR716 VF flexible retainer sheet VF flexible retainer sheet Tapping screw Tapping screw Tapping screw...
Page 36: Removal Of Tr Cover, Cf-60 Board And Display Panel (Tr Series)
2-13. REMOVAL OF TR COVER, CF-60 BOARD AND DISPLAY PANEL ...(TR series) !∞ Liquid crystal display panel Phase adjustment S024 !¢ LCD holder S015 FP-57 flexible board...(Color EVF type only) CN007, 20P Claw Flat cable (FFC-235)...(B/W EVF type only) !™ CF-60 board CN008, 4P !¡...
Page 37: Service Position
2-15. SERVICE POSITION Preparation : Refer to previous section “DISASSEMBLY”, and con- CPC-7 jig (J-6082-382-A) nect as shown in the figure after each parts has been VC-215 board : CN910, 16P removed. Extension cord 70P (J-6082-439-A) —TR series— DD-117 board : CN931 — VC-215 board : CN915 VC-215 board Screw (M2x3) Control switch block...
Page 38: Circuit Boards Location
2-16. CIRCUIT BOARDS LOCATION LB-54... Color EVF models only (Back light) VF-119... Color EVF models only (Color EVF) VF-120... Color EVF models only (Color EVF) CF-60... TR series only DD-117 (Control) (Power) VL-21... TR516/TR516PK/TR716 VF-99... B/W EVF models only VL-22... TRV36/TRV36PK/TRV43/ (B/W EVF) TRV46/TRV46PK...
Page 39: Block Diagrams
I/O R ( TRV MODEL ) TR MODEL : CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 TRV MODEL : CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK COLOR EVF MODEL : CCD-TR416/TR416PK/TR516/TR516PK/TR716 B/W EVF MODEL : CCD-TR315 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK STEADY SHOT MODEL : CCD-TRV43/TRV46/TRV46PK IR TRANSMITTER MODEL : CCD-TRV43/TRV46/TRV46PK REMOTE COMMANDER MODEL : CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3.1V...
Page 40: Camera/Video 1 Block Diagram
TR MODEL : CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CAMERA REC CAMERA REC IC001 TRV MODEL : CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 2.3Vp-p COLOR EVF MODEL : CCD-TR416/TR416PK/TR516/TR516PK/TR716 7Vp-p 2.3Vp-p B/W EVF MODEL : CCD-TR315 28.636 MHz CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK IC501 4.12 MHz 14.32 MHz Q001 IC501 11 12 CAMERA REC CAMERA REC 2.9Vp-p...
Page 41: Vtr/Camera Control Block Diagram
3-3. VTR/CAMERA CONTROL BLOCK DIAGRAM 710 only 3.1V 3.1V 1.7Vp-p 20 MHz IC402 3.1V 3Vp-p 13usec 3.1V IC402 TR MODEL : CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 TRV MODEL : CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK COLOR EVF MODEL : CCD-TR416/TR416PK/TR516/TR516PK/TR716 STEADY SHOT MODEL : CCD-TRV43/TRV46/TRV46PK 3.1V 3Vp-p IC402 3Vp-p IC402 3.1V 3.1V 3.1V 3.1V...
Page 42: Servo Block Diagram
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-4. SERVO BLOCK DIAGRAM 3Vp-p 13usec 3Vp-p IC402 0.76Vp-p 2.8msec 506 kHz IC402 IC801 3.1V 1.2Vp-p 5.6msec IC451 3.1V 3Vp-p 3Vp-p 1.2msec 0.76Vp-p IC402 IC402 507 kHz IC801 3Vp-p 13usec IC402 3-12 3-13 3-14...
Page 43: Mode Control Block Diagram
SELECT (TRV MODEL) 1.5Vp-p 20 MHz IC604 2.6Vp-p 32 kHz IC604 TR MODEL : CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 TRV MODEL : CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK REMOTE COMMANDER MODEL : CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK VIDEO LIGHT MODEL : CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK (VIDEO LIGHT MODEL) (TR MODEL TR516/TR516PK/TR716) (VIDEO LIGHT MODEL)
Page 44: Audio Block Diagram
2usec IC751 0.25Vp-p 3.58 MHz IC751 CAMERA REC 0.36Vp-p IC301 CAMERA REC TR716 only 0.26Vp-p 3.58 MHz IC301 3.1V TR MODEL : CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 TRV MODEL : CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK IR TRANSMITTER MODEL : CCD-TRV43/TRV46/TRV46PK CAMERA REC 2.9Vp-p IC301 3-19 3-20 3-21 3-22...
Page 45: Lcd Block Diagram (Trv Model)
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-7. LCD BLOCK DIAGRAM (TRV MODEL) IC5502 4.7Vp-p IC5502 4.2Vp-p 0.7Vp-p 3.1V 3.1V IC5502 IC5502 4.2Vp-p IC5502 4.2Vp-p 0.44Vp-p 0.2Vp-p IC5502 IC5502 3.1V 0.2Vp-p IC5502 5601 4.7Vp-p Approx.5.8MHz : 4.1Vp-p IC5601 IC5602 DAC AMP FRPT OUT1 FRPV IC5601 4.7Vp-p...
Page 46: Color Evf Block Diagram (Color Evf Model)
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-8. COLOR EVF BLOCK DIAGRAM (COLOR EVF MODEL) FP-57 (FLEXIBLE 7.5Vp-p IC5401 7.2Vp-p IC5401 3.1V LCD902 7.6Vp-p 3.1V IC5401 3.1V 3.1V 3.1V 3Vp-p 3.1V IC5401 3Vp-p 12Vp-p IC5404 IC5301 3Vp-p IC5404 3.4Vp-p 1.84 MHz IC5404 23 24 3.1V 3Vp-p 7.852 kHz...
Page 47: B/W Evf Block Diagram B/W Evf Model
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-9. B/W EVF BLOCK DIAGRAM B/W EVF MODEL T901/T902 2.2Vp-p IC901 1Vp-p IC901 B/W EVF MODEL : CCD-TR315 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-29 3-30 3-31 3-32...
Page 48: Power Block Diagram
(TR MODEL TR516/TR516PK/TR716) (TRV MODEL TRV36/TRV36PK/TRV43/TRV46/TRV46PK) VIDEO 3.1V TR MODEL : CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 TRV MODEL : CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK COLOR EVF MODEL : CCD-TR416/TR416PK/TR516/TR516PK/TR716 B/W EVF MODEL : CCD-TR315 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK STEADY SHOT MODEL : CCD-TRV43/TRV46/TRV46PK IR TRANSMITTER MODEL : CCD-TRV43/TRV46/TRV46PK 3.1V 3.1V 3.1V 3.1V...
Page 49: Frame Schematic Diagram (1)
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 SECTION 4 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM (1) (COLOR EVF MODEL) (TR MODEL) (TR710 ONLY) FRAME...
Page 50 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK FRAME SCHEMATIC DIAGRAM (2) FRAME...
Page 51: Cd-210/211 (Ccd Imager) Board
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS CD-210/211 (CCD IMAGER) PRINTED WIRING BOARD – Ref No. CD-210 BOARD: 4,000 series, CD-211 BOARD: 9,000 series – THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
Page 52 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VC-215 (CAMERA, Y/C PROCESSOR, IN/OUT, REC/PB HEAD AMP, SERVO/SYSTEM CONTROL, SERVO, AUDIO, IR TRANSMITTER, MODE CONTROL) PRINTED WIRING BOARD VC-215 BOARD – Ref No. VC-215 BOARD: 1,000 series – (SIDE B) VC-215 BOARD (SIDE B) C002...
Page 53 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VC-215 BOARD (SIDE A) VC-215 BOARD (SIDE A) C001 A-13 C336 C-11 R093 C-13 R529 E-12 C004 A-14 C337 A-11 D002 C-13 R096 C-14 R531 F-12 C005 B-14 C338 C-12 D501 F-13 R098 D-14 R532 E-12...
Page 54 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (1/10) CAMERA REC 2.3Vp-p NTSC : 28.636 MHz IC501 CAMERA REC 2.3Vp-p NTSC : 14.32 MHz IC501 11 12 CAMERA REC...
Page 55 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. 4-19 4-20 4-21 4-22 CAMERA (2) VC-215 (2/10)
Page 56 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. VC-215 BOARD (3/10) • Refer to page 4–11 for Printed Wiring Board. CAMERA REC CAMERA REC 0.34Vp-p 3Vp-p IC202 IC202 CAMERA REC CAMERA REC 0.84Vp-p 3.1Vp-p 3.58 MHz IC202 IC202 CAMERA REC CAMERA REC 0.5Vp-p...
Page 57 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (4/10) CAMERA REC 0.46Vp-p IC151 0.32Vp-p IC151 IC151 (2.1Vp-p) IC151 (1.6Vp-p) 4-29 4-30 4-27 4-28 IN/OUT VC-215 (4/10)
Page 58 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. VC-215 BOARD (5/10) • Refer to page 4–11 for Printed Wiring Board. CAMERA REC CAMERA REC 0.3Vp-p 7Vp-p 4.12 MHz IC001 Q001 CAMERA REC 0.3Vp-p IC001 TRIG : IC001 0.4Vp-p IC001 0.4Vp-p IC001 0.4Vp-p...
Page 59 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (6/10) CAMERA REC 1.7Vp-p 20 MHz IC402 3Vp-p IC402 3Vp-p IC402 3Vp-p 13usec IC402 3Vp-p 13usec IC402 3Vp-p 13usec IC402 3Vp-p 1.2msec IC402 3Vp-p 2.8msec...
Page 60 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (7/10) CAMERA REC 1.2Vp-p 5.6msec IC451 3Vp-p IC451 3Vp-p 2.8msec IC451 4-38 4-39 4-40 SERVO VC-215 (7/10)
Page 61 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (8/10) CAMERA REC 2.9Vp-p IC301 0.4Vp-p IC301 CAMERA REC 0.36Vp-p IC301 CAMERA REC 0.26Vp-p 3.58 MHz IC301 4-41 4-42 4-43 4-44...
Page 62 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VL-21/22 (VIDEO LIGHT (VIDEO LIGHT MODEL)) • For schematic diagrams. PRINTED WIRING BOARD – Ref No. VL-21 BOARD: 1,000 series – • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (9/10) VL-21/22 BOARD (SIDE B) VL-21/22 BOARD (SIDE A) 0.25Vp-p...
Page 63 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (10/10) 1.5Vp-p 20 MHz IC604 2.6Vp-p (VIDEO LIGHT MODEL) 32 kHz VL-21/22 BOARD IC604 CN151 (SEE PAGE 4–45) 4-51 4-49 4-50 MODE CONTROL...
Page 64 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SE-80/81 (STEADY SHOT (STEADY SHOT MODEL)) PRINTED WIRING BOARD – Ref No. SE-80 BOARD: 4,000 series, SE-81 BOARD: 9,000 series – SE-80 SE-81BOARD SE-80/81 BOARD (SIDE B) SE-80/81 BOARD (SIDE A) C451 C452 C453 C454 C455 C456 C457...
Page 65 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK PJ-90/91 (AV OUT) PRINTED WIRING BOARD – Ref No. PJ-90 BOARD: 4,000 series, PJ-91 BOARD: 9,000 series – PJ-90/91 BOARD (SIDE B) PJ-90/91 BOARD C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 CN101 D101 D102...
Page 66 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK MA-345, 346 (MIC, LASER LINK) PRINTED WIRING BOARD – Ref No. MA-345, 346 BOARD: 9,000 series – MA-345/346 BOARD (SIDE B) MA-345/346 BOARD (SIDE A) POWER CAMERA LIGHT ON/OFF (PLUG IN POWER) 1-672-462- 11 1-672-468- 11 21...
Page 67 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 4-61 4-62 4-63 4-64 MIC, LASER LINK MA-345/346...
Page 68 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CF-60 (CONTROL (TR Series)) PRINTED WIRING BOARD – Ref No. CF-60 BOARD: 4,000 series – CF-60 BOARD (SIDE B) CF-60 BOARD (SIDE A) CF-61 BOARD BH001 C001 BACK LIGHT TITLE PICTURE EFECT C002 CN001 CN002 CN005 CN006 CN007...
Page 69 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK NO MARK CAMERA REC MODE 4-69 4-70 4-71 CONTROL CF-60 (TR Series)
Page 70 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CONTROL 4-72 4-73 4-74 CF-61 (TRV Series)
Page 71 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CF-61 (CONTROL (TRV Series) PRINTED WIRING BOARD – Ref No. CF-61 BOARD: 9,000 series – CF-61 BOARD (SIDE B) CF-61 BOARD (SIDE A) CF-61 BOARD BH001 COUNTER DATE TIME RESET BACK C001 LIGHT C002 CN001 CN002...
Page 72 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK PD-107 (RGB DECODER, LCD DRIVE, BACK LIGHT, LCD (TRV Series)) PRINTED WIRING BOARD – Ref No. PD-107 BOARD: 10,000 series – PD-107 BOARD C5501 B-10 FB5502 R5608 C-10 R5695 R5696 D-10 C5502 B-10 FB5503 R5610 B-10 PD-107 BOARD (SIDE B)
Page 73 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK PD-107 BOARD (1/4) CAMERA REC 0.44Vp-p IC5502 0.2Vp-p IC5502 0.2Vp-p IC5502 0.7Vp-p IC5502 4.7Vp-p IC5502 4.2Vp-p IC5502 4.2Vp-p IC5502 4.2Vp-p IC5502 4-83 4-84 4-85 RGB DECODER PD-107 (1/4) (TRV Series)
Page 74 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–79 for Printed Wiring Board. PD-107 BOARD (2/4) CAMERA REC 4.7Vp-p IC5601 4.7Vp-p 20msec IC5601 4.7Vp-p IC5601 4.1Vp-p IC5601 4.7Vp-p 20msec IC5601 4.7Vp-p IC5601 4-86 4-87 4-88 LCD DRIVE PD-107 (2/4) (TRV Sereis)
Page 75 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • For schematic diagrams. • Refer to page 4–79 for Printed Wiring Board. • Refer to page 4–79 for Printed Wiring Board. PD-107 BOARD (4/4) CAMERA REC 2.9Vp-p 24.17 kHz IC5801 4-89 4-90 4-91...
Page 76 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VF-99 (B/W EVF) PRINTED WIRING BOARD – Ref No. VF-99 BOARD: 10,000 series – VF-99 BOARD (SIDE B) VF-99 BOARD (SIDE A) VF-99 BOARD (TYPE 2/TYPE 3) (TYPE 2) C901 R919 C902 R920 C903 R921 C904 R922 C905...
Page 77 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VF-119 (COLOR EVF (COLOR EVF MODEL)) PRINTED WIRING BOARD VF-119 BOARD – Ref No. VF-119 BOARD: 10,000 series – CAMERA REC VF-119 BOARD (SIDE B) VF-119 BOARD (SIDE A) 3Vp-p IC5401 7.2Vp-p IC5401 7.5Vp-p IC5401 7.6Vp-p IC5401 3Vp-p...
Page 78 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VF-120 BOARD CAMERA REC 2.4Vp-p IC5301 12Vp-p IC5301 4-99 4-100 4-101 4-102 COLOR EVF, BACK LIGHT VF-120 (COLOR EVF MODEL), LB-54...
Page 79 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VF-120 (COLOR EVF), LB-54 (BACK LIGHT) (COLOR EVF MODEL) PRINTED WIRING BOARDS – Ref No. VF-120 BOARD: 10,000 series, LB-54 BOARD: 10,000 series – VF-120 BOARD (SIDE B) VF-120 BOARD (SIDE A) LB-54 BOARD (SIDE B)
Page 80 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK DD-117 (POWER) PRINTED WIRING BOARD – Ref No. DD-117 BOARD: 2,000 series – DD-117 BOARD (SIDE B) DD-117 BOARD (SIDE A) DD-117 BOARD L801 R822 C801 C802 L802 R824 C803 L803 R825 C804 L804 R826 C805 L805 R827...
Page 81 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK DD-117 BOARD CAMERA REC 0.76Vp-p 507 kHz IC801 0.76Vp-p 506 kHz IC801 4-109 4-110 4-111 4-112E POWER DD-117...
Page 82: Adjustments
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 5 ADJUSTMENTS Refer to page 3 as Table for distinction functions of models and classification 5-1. CAMERA SECTION ADJUSTMENTS 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope •...
Page 83: Preparations
1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. 1) Connect the equipment for adjustments according to Fig. 5-1-3, 2) By setting the “Forced Camera Power ON mode”, the camera power can be turned ON even if the front panel block (MA-345/ Pattern box...
Page 84 TR MODEL Color monitor Vector scope Terminated at 75 Ω Lens block CD-210 board Regulaterd power supply CN401 (8.4 ± 0.1 Vdc) Battery terminal (Note 1) Extension cable(16P) (J-6082-357-A) Adjusting VL-21 board remote CN151 commander Battery switch VIDEO terminal LANC CN935 CN909 terminal...
Page 85 TRV MODEL Color monitor Vector scope Terminated at 75 Ω Lens block CD-211 board Regulaterd power supply CN401 (8.4 ± 0.1 Vdc) Battery terminal (Note 2) Extension cable(16P) (J-6082-357-A) Adjusting VL-22 board remote CN151 commander Battery switch VIDEO terminal LANC CN935 jack CN909...
Page 86: Setting The Switch
1-1-3.Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. 1. POWER switch (MA-345/346 board) ....CAMERA 7. FOCUS switch (MF-8500) ........MANUAL 2. NIGHT SHOT switch (Lens Block) ........ OFF 8.
Page 87: Adjusting Remote Commander
1-1-4. Adjusting Remote Commander • Changing the address The adjusting remote commander is used for changing the calcula- The address increases when the FF ()) button is pressed, tion coefficient in signal processing, EVR data, etc. The adjusting and decreases when the REW (0) button is pressed. There remote commander performs bi-directional communication with the are altogether 256 addresses, from 00 to FF.
Page 88: Data Processing
1-1-5. Data Processing The calculation of the DDS display and the adjusting remote calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Table 5-1-2. indicates the hexadecimal commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items.
Page 89: Initialization Of D, E, F
1-2. INITIALIZATION OF D, E, F PAGE DATA 2. Modification of D, E, F Page Data If the D, E, F page data has been initialized, change the data of the 1. Initializing the D,E,F Page Data “Fixed data-2” address shown in the following tables by manual Note 1: If “Initializing the D, E, F Page Data”...
Page 90 3. D Page Table Note1 : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Address Initial Remark Address Initial Remark Value Value 00 to 0F...
Page 91 Flange back adj. below, and the initial value of adjustment is different ac- cording to the model. Hi8 model :CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK Standard8 model : CCD-TR315/TR416/TR416PK Angular velocity sensor sensitivity check CCD-TRV16/TRV16PK Address 43, 44 and fixed data address. (CCD-TR716, TRV43/TRV46/TRV46PK)
Page 92 Address Initial Remark Address Initial Remark Value Value Fixed data-2 Switching position adj. Fixed data-1 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1:CCD-TR516/TR516PK, TRV36/TRV36PK Fixed data-2:CCD-TR716, TRV43/TRV46/TRV46PK Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-2 Fixed data-1...
Page 93 5. E Page Table Address Initial Remark Note 1: Value Fixed data-1 : Initialized data. Fixed data-1 ( Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Fixed data-2 Note 2: See “1-5.
Page 94 Address Initial Remark Address Initial Remark Value Value Fixed data-1 Fixed data-2 Fixed data-1 TR model:Fixed data-1/TRV model:Fixed data-2 Fixed data-2 Fixed data-1 Fixed data-1 Fixed data-2 Fixed data-1 TR model:Fixed data-1/TRV model:Fixed data-2 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1...
Page 95: Camera System Adjustments
1-3. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, Check that the specified value of “28MHz Origin Oscillation Adjustment”, “Y OUT level Adjustment” and “C OUT level Adjustment” of “VIDEO SYSTEM ADJUSTMENT” are satisfied. 1. G-CAM flip Adjustment Set the color reproduction conditions to optimum. Subject Color bar chart standard picture frame Measurement Point...
Page 96: Hall Adjustment
2. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain and offset. Subject Not required Measurement Point DDS display data of LCD or TV monitor (Note 3) Measuring Instrument Adjustment Page Adjustment Address 2F, 30 Specified Value 7E to 82 during IRIS OPEN (Note 1) 13 to 17 during IRIS CLOSE (Note 2)
Page 97: Flange Back Adjustment
3. Flange Back Adjustment 3-2. Flange Back Adjustment (2) The inner focus lens flange back adjustment is carried out auto- Perform this adjustment after performing “Flange Back Adjustment matically. In whichever case, the focus will be deviated during auto (1)”. focusing/manual focusing.
Page 98: Flange Back Check
4. Flange Back Check 5. Picture Frame Setting Subject Siemens star chart Subject Color bar chart standard picture frame (2.0 m from the front of the lens) (1.5m from the front of the lens) (Luminance: approx. 200 lux) Measurement Point Video output terminal Measurement Point Check operation on TV monitor...
Page 99: Color Reproduction Adjustment
6. Color Reproduction Adjustment Adjust the color Separation matrix coefficient so that proper color reproduction is produced. Subject Color bar chart standard picture frame Measurement Point Video output terminal Measuring Instrument Vectorscope Adjustment Page Adjustment Address 34, 36, F5, F6 Specified Value All color luminance points should settle within each color reproduction frame.
Page 100: Iris In/Out Adjustment
7. IRIS IN/OUT Adjustment 8. MAX GAIN Adjustment For the unit to judge if the white balance is indoors or outdoors in Setting the minimum illumination. auto white balance operations, measure the light level and write it If it is not consistent, the image level required for taking subjects in in the EEPROM.
Page 101: Auto White Balance Standard Data Input
9. Auto White Balance Standard Data Input 10. Auto White Balance Adjustment Adjust to the proper auto white balance output data. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color bar standard picture frame) be poor.
Page 102: White Balance Check
11. White Balance Check Subject Clear chart (Color bar standard picture frame) Filter Filter C14 for color temperature correction ND filter 1.0 and 0.3 2 mm Measurement Point video output terminal Measuring Instrument Vectorscope Specified Value Fig. 5-1-11. A to C Switch setting: 1) NIGHT SHOT switch ............
Page 103: Angular Velocity Sensor Sensitivity Check
12. Angular Velocity Sensor Sensitivity Check (CCD-TR716/TRV43/TRV46/TRV46PK) • This adjustment is performed only when replacing the angular velocity sensor. Although this adjustment need not be performed when the circuit is damaged, etc., check the operations. • Note down the sensitivity displayed on the angular velocity sensor of the repair parts.
Page 104: (Ccd-Tr416/Tr416Pk/Tr516/Tr516Pk/Tr716)
1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM 1. EVF Initial Data Input ADJUSTMENT Mode VTR stop (CCD-TR416/TR416PK/TR516/TR516PK/TR716) Signal No signal Note 1: The back light (fluorescent tube) is driven by a high volt- Adjustment Page age AC power supply. Therefore, do not touch the back Adjusting Address C2 to CD light holder to avoid electrical shock.
Page 105: Vco Adjustment (Vf-119 Board)
2. VCO Adjustment (VF-119 board) 3. Bright Adjustment (VF-119 board) Set the VCO free-run frequency. If deviated, the EVF screen will be Set the level of the VIDEO signal for driving the LCD to the speci- blurred. fied value. If deviated, the screen image will be blackish or satu- rated (whitish).
Page 106: Contrast Adjustment (Vf-119 Board)
4. Contrast Adjustment (VF-119 board) 5. Backlight Consumption Current Adjustment (VF-120 Set the level of the VIDEO signal for driving the LCD to the speci- board) fied value. If deviated, the screen image will be blackish or satu- Set the backlight luminance and color temperature. rated (whitish).
Page 107: Monochrome Electronic Viewfinder System Adjustments
1-5. MONOCHROME ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENTS Note: CCD-TR315 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/ TRV46/TRV46PK 1-5-2. Centering Adjustment 1-5-1. Horizontal Slant Check Mode Playback Mode Playback Signal Alighment tape : Signal Alighment tape : For checking operations For checking operations (WR5-5NSP) (WR5-5NSP) Monoscope section Monoscope section Specified Value ±...
Page 108: Aberration Adjustment
1-5-4. Aberration Adjustment 1-5-5. Horizontal Amplitude Adjustment (VF-99 board) Mode VTR stop Signal Dot pattern Mode Playback Specified Value b1 2 • a1 Signal Alighment tape : b2 0.8 • a2 For checking operations (WR5-5NSP) Adjusting method: Monoscope section 1) Adjust the aberration adjustment ring so that the tracing of the Adjusting Element C909 (SOL901) dot satisfies the specified value.
Page 109: Vertical Amplitude Adjustment (Vf-99 Board)
1-5-6. Vertical Amplitude Adjustment (VF-99 board) 1-5-7. Brightness Adjustments (VF-99 board) Mode Playback Mode Playback Signal Alighment tape : Signal Alighment tape : For checking operations For checking operations (WR5-5NSP) (WR5-5NSP) Monoscope section Monoscope section Adjusting Element RV903 Specified Value RV904 Specified Value 10 ±...
Page 110: Lcd System Adjustment (Trv Series)
1-6. LCD SYSTEM ADJUSTMENT (TRV series) 1. LCD Initial Data Input Note1: The back light (fluorescent tube) is driven by a high volt- Mode VTR stop age AC power supply. Therefore, do not touch the back Signal Arbitrary light holder to avoid electrical shock. Adjustment Page Note2: When replacing the LCD unit, be careful to prevent dam- Adjustment Address...
Page 111: Vco Adjustment (Pd-107 Board)
2. VCO Adjustment (PD-107 board) 3. D range Adjustment (PD-107 board) Set the VCO freerun frequency. If deviated, the LCD screen will be Set the D range of the RGB decoder used to drive the LCD to the blurred. specified value. If deviated, the LCD screen will become blackish or saturated (whitish).
Page 112: Bright Adjustment (Pd-107 Board)
4. Bright Adjustment (PD-107 board) 5. Contrast Adjustment (PD-107 board) Set the level of the VIDEO signal for driving the LCD to the speci- Set the level of the VIDEO signal for driving the LCD to the speci- fied value. If deviated, the screen image will be blackish or satu- fied value.
Page 113: V-Com Adjustment (Pd-107 Board)
6. V-COM Adjustment (PD-107 board) 7. Color Adjustment (PD-107 board) Set the common electrode drive signal level of LCD to the specified Set the color saturation to the standard value. If deviated, the color value. will be to dark or light. Mode VTR stop Mode...
Page 114: V-Com Adjustment (Pd-107 Board)
8. V-COM Adjustment (PD-107 board) 9. White Balance Adjustment (PD-107 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and con- Mode VTR stop...
Page 115: Mechanical Section Adjustment
5-2. MECHANICAL SECTION ADJUSTMENT 6) Connect the oscilloscope. Channel 1: Pin 6 of CN910 of VC-215 board External trigger: Pin !¡ of CN910 of VC-215 board Mechanism Parts Adjustments Connect the oscilloscope via the CPC-7 jig For details on the adjustments and checks of mechanical section (J-6082-382-A).
Page 116: Video Section Adjustments
5-3. VIDEO SECTION ADJUSTMENTS When performing adjustments, refer to the layout diagrams for adjustment related parts beginning from page 5-60. 3-1. PREPARATIONS BEFORE ADJUSTMENT The following adjusting instruments are used for adjusting the video section. 3-1-1. Equipments to be Used 1) TV monitor 2) Oscilloscope: 2 phenomena, band 30 MHz or wider, with delay mode.
Page 117: Precautions On Adjusting
3-1-2. Precautions on Adjusting 3-1-3. Adjusting Connectors 1) The adjustments of this unit are performed in the VTR mode or Some of the adjusting points of the video section are concentrated camera mode. at VC-215 board CN910. Connect the measuring instruments via To set to the VTR mode, set the power switch to “VTR”...
Page 118: Connecting The Equipments
3-1-4. Connecting the Equipments Connect the measuring instruments as shown in Fig. 5-3-2 and perform the adjustments. Connecting the TV Monitor and Regulated Power Supply Battery terminal Main Unit TV monitor Regulated power supply 8.4 ± 0.1Vdc VIDEO Connect when using the camera mode or playing back.
Page 119 Note: Measure using the VIDEO terminal (Terminated at 75 Ω). Fig. 5-3-3. shows the 75% color bar signals recorded on the align- ment tape. Fig. 5-3-3. Color Bar Signals of the Alignment Tape 5-38...
Page 120: Output Level And Impedance
3-1-6. Output Level and Impedance 3-1-8. Service Mode Video output Additional note on adjustment Note: After the completion of the all adjustments, cancell the ser- Phono jack, 1 Vp-p, 75Ω, unbalanced, sync negative vice mode by either of the following ways. Audio output Phono jack, –7.5 dBs, (at load impedance 47 kΩ), 1) Unplug the main power supply and remove the lithium battery.
Page 121: Emergency Memory Address
2. Emergency Memory Address 2-1. EMG CODE (Emergency Code) The codes shown in the following table which correspond to errors Page F Address 10 to 1B that occur are recorded in addresses 10, 14, and 18. Address Contents Code Type of Emergency 1st EMG code No error Upper: MSW code when the mechanism starts shifting...
Page 122: Msw Codes
2-2. MSW Codes • The lower parts of the data of addresses 12, 16 and 1A represent the MSW codes (mode switch, mechanism position) when errors occurs. • The upper parts of the data of addresses 12, 16 and 1A represent, when the mechanism position is to be moved, the MSW codes at the start of movement (when moving the loading motor).
Page 123: Bit Value Discrimination
3. Bit value discrimination 4. Switch check (1) Bit values must be discriminated using the display data of the ad- Page 3 Address 43 justing remote commander for the following items. Use the table below to discriminate if the bit value is “1” or “0”. Function When bit value=1 When bit value=0 0 VTR MODE SW...
Page 124: Switch Check (2)
5. Switch check (2) Page 3 Address 60 to 66 Using method: 1) Select page: 3, address: 60 to66. 2) By discriminating the display data, the pressed key can be dis- c r i m i n a t e d . Data Address 00 to 0D...
Page 125: Led, Lcd (Display Window) Check
8. LED, LCD (display window) check 9. Record of Use Check Page 3 Address 05 Bit5 Page 3 Address A2 to AA Address Function Remarks Using method: 1) Select page: 3, address: 05, and set the bit value of Bit5 to “1”. 1000th place digit and 2) Check that all LED are lit and all segments of LCD (display 100th place digit of...
Page 126: System Control System Adjustment
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Initialization of D, E, F Page Data If the D, E, F page data is erased due to some reason, perform “1-2. INITIALIZATION OF D, E, F PAGE DATA”, of “5-1. CAMERA SECTION ADJUSTMENT”. 2.
Page 127: Servo System Adjustments
3-3. SERVO SYSTEM ADJUSTMENTS 2. RF Switching Position Adjustment (VC-215 Board) If deviated in this case causes switching noise or jitter on the played 1. CAP FG Offset Adjustment (VC-215 board) back screen. Improve the capstan servo characteristic. If it is not correct. jitters Mode Playback will increase.
Page 128: Video System Adjustments
3-4. VIDEO SYSTEM ADJUSTMENTS 1. 28 MHz Origin Oscillation Adjustment (VC-215 board) Set the frequency of the clock for synchronization. Video system adjustments must be performed in the following order. If deviated, the synchronization will be disrupted and the color will become inconsistent.
Page 129: Afc F0 Adjustment (Vc-215 Board)
2. AFC f0 Adjustment (VC-215 board) 3. Filter f0 Adjustment (VC-215 board) Adjust the pull-in range of the A/D converted clock generator dur- Minimize the chroma signal residual components during compos- ing playback. ite video signal input. Mode VTR stop Mode VTR stop Signal...
Page 130: Y Out Level Adjustment (Vc-215 Board)
Note 1 : Hi8 model CCD-TR516/TR516PK/TR716 CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK : Standard8 model : Standard8 model CCD-TR315/TR416/TR416PK CCD-TR315/TR416/TR416PK CCD-TRV16/TRV16PK CCD-TRV16/TRV16PK Adjusting method: Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 1) Select page: 0, address: 01, and set data: 01.
Page 131: Rp Filter F0 Adjustment (Vc-215 Board)
6. RP Filter f0 Adjustment (VC-215 board) Adjust the LPF of the playback RF amplifier. Mode VTR stop Signal No signal Pin 9 of CN910 (RF AGC OUT) Measurement Point Measuring Instrument Oscilloscope Adjustment Page Adjustment Address Specified Value A = Below 10mVp-p Connection: 1) Input a 14.2MHz, 400mVp-p CW signal to Pin 7 of CN910 (RF AGC IN).
Page 132: Hi8 Rec Y Current Adjustment (Vc-215 Board)
7. Hi8 REC Y Current Adjustment (VC-215 board) 14) Write the following data in page: F, address: 57 to 5A. CCD-TR516/TR516PK/TR716 Address Data CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK Adjust the Y FM signal recording current. Mode VTR recording (SP mode) Signal No signal Pin !º of CN910 (REC RF) Measurement Point Note: After setting each data, be sure to press the PAUSE button Measuring Instrument Oscilloscope...
Page 133: Ccd-Trv16/Trv16Pk
8. Standard8 REC Y Current Adjustment (VC-215 board) 14) Write the following data in page: F, address: 57 to 5A. CCD-TR315/TR416/TR416PK Address Data CCD-TRV16/TRV16PK Adjust the Y FM signal recording current. Mode VTR recording (SP mode) Signal No signal Pin !º of CN910 (REC RF)
Page 134: Hi8 Rec L Level Adjustment (Vc-215 Board)
9. Hi8 REC L Level Adjustment (VC-215 board) 13) Calculate the adjustment data (hexadecimal) from the follow- CCD-TR516/TR516PK/TR716 ing equations (hexadecimal calculation), and input each adjust- CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK ment address. (Refer to Table 5-1-2. Hexadecimal-Decimal Set the recording levels of the REC AFM signal and REC ATF sig- conversion Table.) nal.
Page 135: Standerd8 Rec L Level Adjustment
10. Standard8 REC L Level Adjustment (VC-215 board) 14) Write the following data in page: F, address: 63 to 64. CCD-TR315/TR416/TR416PK Address Data CCD-TRV16/TRV16PK Set the recording levels of the REC AFM signal and REC ATF sig- nal. If the level is too low, the audio S/N will deteriorated, tracking will not be stable, or SP/LP will not be discriminated properly.
Page 136: Ccd-Trv16/Trv16Pk
A = 30.0±1.1mV Note 1: Hi8 model: CCD- TR516/TR516PK/TR716 1.35 µ sec CCD- TRV36/TRV36PK/TRV43/TRV46/ TRV46PK Standard8 model: CCD-TR315/TR416/TR416PK Fig. 5-3-16. CCD-TRV16/TRV16PK Connection: 1) Remove C085 (0.01µF, Pin !§ of IC202). Note: After completing “REC L Level Adjustment” and “REC C Current Adjustment”, replace C085 with new parts (1-162-...
Page 137: Ir Transmitter Adjustments (Ccd-Trv43/Trv46/Trv46Pk)
3-5. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (VC-215 board) (CCD-TRV43/TRV46/TRV46PK) Mode Camera standby Subject Arbitrary Adjust using a IR receiver jig (J-6082-383-A). Measurement Point VIDEO OUT terminal of IR receiver jig (Terminated at 75Ω) Switch setting: Measuring Instrument Oscilloscope LASER LINK ....
Page 138: Ir Audio Deviation Adjustment (Vc-215 Board)
3. IR Audio Deviation Adjustment (VC-215 board) Mode VTR recording Signal Audio signal : 400Hz, –7.5dBs : AUDIO terminal Video signal : Color bar signal : VIDEO terminal Measurement Point AUDIO terminal of IR receiver jig ( Terminated at 47kΩ) Measuring Instrument Audio level meter Adjustment Page...
Page 139: Mhz Deviation Adjustment (Vc-215 Board)
3-6. AUDIO SYSTEM ADJUSTMENT 1. 1.5 MHz Deviation Adjustment (VC-215 board) Adjust to the optimum audio FM signal distortion. [Connecting the measuring instruments for the audio] If the adjustment is not correct, its playback level will differ from Connect the audio system measuring instruments besides the video that of other units.
Page 140: Arrangement Diagram For Adjustment Parts
3-7. ARRANGEMENT DIAGRAM FOR ADJUSTMENT PARTS VC-215 BOARD (SIDE A) CN909 CN551 CN501 IC604 IC202 CN911 C085 IC001 IC301 VC-215 BOARD (SIDE B) IC501 CN910 IC751 5-59 5-60E...
Page 141: Repair Parts List
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: The components identified by • Items marked “*” are not stocked since they are • Abbreviation mark ! or dotted line with mark seldom required for routine service. Some delay Canadian model is abbreviated as CND.
Page 142: Cabinet (L) And Battery Panel Assembly
6-1-2. CABINET (L) AND BATTERY PANEL ASSEMBLY not supplied not supplied not supplied not supplied J901 See page 6-6 not supplied S003 J001 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-962-826-01 SCREW (2 x 4) 3-987-717-01 SCREW, TRIPOD 3-948-339-61 TAPPING 3-987-679-01 SHEET METAL (LOWER), STRAP...
Page 143: Front Panel Block Assembly
6-1-3. FRONT PANEL BLOCK ASSEMBLY Video light model CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK No video light CCD-TR315/TR416/TR416PK model CCD-TRV16/TRV16PK - 3 4 not supplied not supplied not supplied not supplied No video light models LAMP,HALOGEN MIC901 VL901 XB-3D(DC6V/3W) Video light models The components identified by Les composants identifiés par une...
Page 144: Cabinet (R) Block Assembly (Tr Series)
6-1-4. CABINET (R) BLOCK ASSEMBLY (TR series) not supplied See pages 6-7 to 6-8 LCD903 B/W view finder CCD- TR315 model Color view finder CCD- TR416/TR416PK/TR516/ model TR516PK/TR716 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-475-620-11 SWITCH BLOCK, CONTROL (MF-8500) A-7073-821-A CF-60 (N) BOARD, COMPLETE (TR315) X-3949-179-1 CABINET (R) ASSY (TR516/TR516PK/TR716)
Page 145: Cabinet (R) Block Assembly (Trv Series)
6-1-5. CABINET (R) BLOCK ASSEMBLY (TRV series) See page 6-8 not supplied not supplied SP901 See page 6-9 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-475-620-11 SWITCH BLOCK, CONTROL (MF-8500) X-3949-321-1 COVER ASSY, IR (TRV36/TRV36PK) X-3949-280-1 CABINET (R) ASSY X-3949-404-1 COVER ASSY, IR (TRV16:TW) (TRV36/TRV36PK/TRV43/TRV46/TRV46PK)
Page 146: Main Boards Block Assembly
6-1-6. MAIN BOARDS BLOCK ASSEMBLY Video light model CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK No video light CCD-TR315/TR416/TR416PK model CCD-TRV16/TRV16PK No video light models See page 6-10 not supplied - 1 1 - 2 1 Video light models SE452 See pages 6-11 to 6-13 SE451 CCD-TR716 &...
Page 147 6-1-7. COLOR EVF BLOCK ASSEMBLY (Color View Finder models CCD-TR416/TR416PK/TR516/TR516PK/TR716) Note : As for the model whitch carries a B/W view finder, refer to page 6-8. LCD902 not supplied ND5351 not supplied The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety.
Page 148: B/W Evf Block Assembly (Ccd-Tr315 And Trv Series)
6-1-8. B/W EVF BLOCK ASSEMBLY (B/W View Finder models CCD-TR315 and TRV series) Note : As for the model whitch carries a color view finder, refer to page 6-7. V901 The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety.
Page 149: Lcd Block Assembly (Trv Series)
6-1-9. LCD BLOCK ASSEMBLY (TRV series) ND801 - 1 0 LCD901 LCD903 The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety. sécurité. Replace only with part number Ne les remplacer que par une specified.
Page 150: Zoom Lens Block Assembly
6-1-10. ZOOM LENS BLOCK ASSEMBLY not supplied M906 M905 IC401 Be sure to read “Note on the CCD Imager replacement” on page 4–8 when changing the CCD imager. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 8-848-722-01 DEVICE, LENS (LSV-600A) 1-668-959-11 FP-623 FLEXIBLE BOARD 3-713-791-51 SCREW (M1.7 x 3.5), TAPPING, P2...
Page 151: Cassette Compartment Assembly
6-1-11. CASSETTE COMPARTMENT ASSEMBLY See page 6-13 See page 6-12 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7040-421-A DAMPER ASSY X-3945-399-1 GEAR ASSY, GOOSENECK 7-624-102-04 STOP RING 1.5, TYPE -E 3-947-503-01 SCREW (M1.4X2.5) X-3949-153-2 CASSETTE COMPARTMENT ASSY 3-331-007-21 WASHER 3-965-587-03 SPRING (POWER, TENSION), TENSION 3-727-176-01 WASHER, STOPPER...
Page 152: Ls Chassis Assembly
6-1-12. LS CHASSIS ASSEMBLY S002 S001 D001 FP-249 (not supplied) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7040-419-A BASE (S) BLOCK ASSY, GUIDE 3-965-563-01 GEAR, T SOFT A-7040-418-B BASE (T) BLOCK ASSY, GUIDE 3-965-559-01 STOPPER (T) 3-965-565-01 CLAW, T SOFT 3-965-557-01 STOPPER (T), GB X-3945-397-1 DECK ASSY, REEL, S...
Page 153: Mechanism Chassis Assembly
6-1-13. MECHANISM CHASSIS ASSEMBLY M901 81 1 M903 M902 S901 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3947-343-1 GROUND (IM) ASSY, SHAFT 3-965-535-01 SPRING (LIMITTER ARM S), COIL 3-965-550-02 SCREW (M1.7X1.6) 3-965-542-01 SHIELD, MOTOR 1-657-785-11 FP-248 FLEXIBLE BOARD (DEW SENSOR) 3-965-539-01 GEAR (A)
Page 154: Electrical Parts List
CD-210/211 CF-60/61 6-2. ELECTRICAL PARTS LIST Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by In each case, u: µ , for example: may be different from the parts specified in the mark ! or dotted line with mark uA...: µ...
Page 155 CF-60/61 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > S010 1-771-029-21 SWITCH, TACTILE (MENU) (TR315/TR416/TR416PK/TR516/TR516PK/TR716) Q001 8-729-402-42 TRANSISTOR UN5213-TX S010 1-771-138-61 SWITCH, KEY BOARD (MENU) (TR315/TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) S012 1-771-029-21 SWITCH, TACTILE (EXPOSURE) <...
Page 156 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C811 1-162-965-11 CERAMIC CHIP 0.0015uF 10% C864 1-113-985-11 TANTAL. CHIP 10uF C812 1-162-964-11 CERAMIC CHIP 0.001uF C865 1-117-720-11 CERAMIC CHIP 4.7uF C813 1-162-964-11 CERAMIC CHIP 0.001uF (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) C815 1-162-964-11 CERAMIC CHIP 0.001uF...
Page 157 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < COIL > Q815 8-729-046-98 TRANSISTOR CPH6702-TL Q819 8-729-046-98 TRANSISTOR CPH6702-TL L804 1-412-056-11 INDUCTOR CHIP 4.7uH (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) L805 1-409-532-41 INDUCTOR 33uH Q823 8-729-037-74 TRANSISTOR UN9213J-(K8).SO (TR315/TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) Q823 8-729-042-29 TRANSISTOR RN1104F(TPL3) L805...
Page 158 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q856 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3) R852 1-218-851-11 RES,CHIP 1.5K 0.50% 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) Q932 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R853 1-216-849-11 METAL CHIP 220K 1/16W (TRV43/TRV46/TRV46PK) (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) Q932 8-729-042-29 TRANSISTOR RN1104F(TPL3) (TRV43/TRV46/TRV46PK) R854 1-218-887-11 RES,CHIP...
Page 159 FP-249 FP-355 LB-54 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R900 1-218-895-11 RES,CHIP 100K 0.50% 1/16W < HALL ELEMENT > R901 1-218-887-11 RES,CHIP 0.50% 1/16W H001 8-719-033-37 ELEMENT, HALL HW-105C R902 1-216-864-11 METAL CHIP 1/16W H002 8-719-033-37 ELEMENT, HALL HW-105C R903...
Page 160 1-216-864-11 METAL CHIP 1/16W R309 1-216-847-11 METAL CHIP 150K 1/16W D301 8-719-061-86 DIODE DCR2810 (TRV43/TRV46/TRV46PK) (TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) D302 8-749-060-65 DIODE DCC3810 D303 8-719-061-82 DIODE TLSU1002(TPX1,SONY) R310 1-216-824-11 METAL CHIP 1.8K 1/16W D305 8-719-073-01 DIODE MA111-(K8).S0 R311 1-216-841-11 METAL CHIP 1/16W (TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) R311...
Page 161 MA-345/346 PD-107 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R312 1-216-864-11 METAL CHIP 1/16W C5616 1-107-682-11 CERAMIC CHIP (TRV43/TRV46/TRV46PK) C5618 1-113-994-11 TANTAL. CHIP 6.8uF R313 1-216-864-11 METAL CHIP 1/16W C5619 1-162-970-11 CERAMIC CHIP 0.01uF R314 1-216-815-11 METAL CHIP 1/16W C5620...
Page 162 PD-107 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q5606 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX R5674 1-216-864-11 METAL CHIP 1/16W R5676 1-216-864-11 METAL CHIP 1/16W Q5607 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX Q5608 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX R5679 1-216-805-11 METAL CHIP 1/16W Q5701 8-729-039-43 TRANSISTOR FP216-TL R5680...
Page 163 PJ-90 SE-80/81 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > C466 1-162-970-11 CERAMIC CHIP 0.01uF (TR716/TRV43/TRV46/TRV46PK) D102 8-719-062-16 DIODE 01ZA8.2(TPL3) D103 8-719-062-16 DIODE 01ZA8.2(TPL3) < CONNECTOR > < JACK > CN451 1-766-646-21 CONNECTOR, FFC/FPC 10P (TR716/TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) J101 1-537-747-41 TERMINAL BOARD (VIDEO/AUDIO)
Page 164 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7094-112-A VC-215(ZSL0) BOARD, COMPLETE (TR315) C062 1-162-926-11 CERAMIC CHIP 82PF C065 1-162-970-11 CERAMIC CHIP 0.01uF **************************** C068 1-162-921-11 CERAMIC CHIP 33PF A-7094-117-A VC-215(VZB0) BOARD, COMPLETE C069 1-162-970-11 CERAMIC CHIP 0.01uF ***************************** (TRV36/TRV36PK)
Page 165 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C233 1-162-638-11 CERAMIC CHIP C412 1-162-969-11 CERAMIC CHIP 0.0068uF 10% C234 1-162-970-11 CERAMIC CHIP 0.01uF C414 1-164-156-11 CERAMIC CHIP 0.1uF C235 1-162-970-11 CERAMIC CHIP 0.01uF C415 1-164-156-11 CERAMIC CHIP 0.1uF C237 1-164-156-11 CERAMIC CHIP...
Page 166 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C522 1-107-826-91 CERAMIC CHIP 0.1uF C754 1-107-823-11 CERAMIC CHIP 0.47uF C523 1-115-467-11 CERAMIC CHIP 0.22uF (TRV43/TRV46/TRV46PK) C755 1-107-823-11 CERAMIC CHIP 0.47uF C524 1-162-962-11 CERAMIC CHIP 470PF (TRV43/TRV46/TRV46PK) C525 1-162-970-11 CERAMIC CHIP 0.01uF...
Page 167 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CN908 1-774-639-21 CONNECTOR, FFC/FPC 15P L003 1-414-406-11 INDUCTOR 220uH CN909 1-764-703-11 CONNECTOR, FFC/FPC (LIF) 4P L004 1-414-754-11 INDUCTOR 10uH (TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) L005 1-412-948-11 INDUCTOR 5.6uH CN910 1-766-346-21 CONNECTOR, FFC/FPC 16P CN911 1-785-760-21 CONNECTOR, FFC/FPC (ZIF) 45P L006...
Page 168 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q044 8-729-042-29 TRANSISTOR RN1104F(TPL3) R006 1-216-825-11 METAL CHIP 2.2K 1/16W Q151 8-729-037-61 TRANSISTOR RN2104F(TPL3) R007 1-216-829-11 METAL CHIP 4.7K 1/16W R008 1-216-814-11 METAL CHIP 1/16W Q153 8-729-040-77 TRANSISTOR 2SC5376-B(TE85L) R009 1-216-813-11 METAL CHIP 1/16W...
Page 169 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R087 1-216-821-11 METAL CHIP 1/16W R227 1-216-811-11 METAL CHIP 1/16W R088 1-216-864-11 METAL CHIP 1/16W R092 1-216-809-11 METAL CHIP 1/16W R228 1-216-813-11 METAL CHIP 1/16W R093 1-216-833-11 METAL CHIP 1/16W R229 1-216-805-11 METAL CHIP...
Page 170 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R377 1-216-834-11 METAL CHIP 1/16W R461 1-216-853-11 METAL CHIP 470K 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) R378 1-216-825-11 METAL CHIP 2.2K 1/16W R462 1-216-853-11 METAL CHIP 470K 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) R463 1-216-853-11 METAL CHIP 470K 1/16W R464...
Page 171 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R565 1-216-833-11 METAL CHIP 1/16W R649 1-216-857-11 METAL CHIP 1/16W R566 1-216-835-11 METAL CHIP 1/16W R650 1-219-570-11 RES,CHIP 1/16W R567 1-216-825-11 METAL CHIP 2.2K 1/16W R651 1-216-845-11 METAL CHIP 100K 1/16W R569...
Page 172 VC-215 VF-99 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R768 1-216-847-11 METAL CHIP 150K 1/16W A-7066-792-A VF-99 (YM)(YS)(VHL4) BOARD, COMPLETE (TRV43/TRV46/TRV46PK) ************************************ R770 1-216-847-11 METAL CHIP 150K 1/16W (TR315/TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) (TRV43/TRV46/TRV46PK) (Ref.No. 10,000 Series) R771 1-216-818-11 METAL CHIP 1/16W (TRV43/TRV46/TRV46PK) <...
Page 173 VF-99 VF-119 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R910 1-216-835-11 METAL CHIP 1/16W C5421 1-162-927-11 CERAMIC CHIP 100PF R911 1-216-160-00 RES,CHIP 1/8W R912 1-216-857-11 METAL CHIP 1/16W C5422 1-135-259-11 TANTAL. CHIP 10uF 6.3V R916 1-218-879-11 RES,CHIP 0.50% 1/16W C5423...
Page 174 VF-119 VF-120 VL-21/22 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R5446 1-216-837-11 METAL CHIP 1/16W R5310 1-216-842-11 METAL CHIP 1/16W R5447 1-216-833-11 METAL CHIP 1/16W R5311 1-216-850-11 METAL CHIP 270K 1/16W R5448 1-216-839-11 METAL CHIP 1/16W R5312 1-216-843-11 METAL CHIP...
Page 175 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MISCELLANEOUS ACCESSORIES ************* ************ 1-475-619-11 SWITCH BLOCK, CONTROL (SS-8500) 1-467-574-21 REMOTE COMMANDER (RMT-708) 1-475-617-11 SWITCH BLOCK, CONTROL (FK-8500) (TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) (TR series/TRV16/TRV16PK/TRV36/TRV36PK) 1-475-599-11 ADAPTOR, AC (AC-L10) 1-475-617-21 SWITCH BLOCK, CONTROL (FK-8500) 1-569-008-21 ADAPTOR, CONVERSION 2P (TRV43/TRV46/TRV46PK) (TR315/TR416:BR/TR416PK/TR516PK/TRV16:E,BR,HK,TW/TRV16PK/...
Page 176 Take a copy CAMERA COLOR REPRODUCTION FRAME and Parts reference sheets with a clear sheet for use. FOR CAMERA COLOR REPRODUCTION ADJUSTMENT CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK < PARTS REFERENCE SHEET > You can find the parts position of mount locations applying to boards of a set.
Page 177 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK Sony Corporation 98L0931-1 Printed in Japan © 1998. 12 9-974-124-11 Personal A&V Products Company Published by Quality Engineering Dept. – 290 – (Osaki East)

This manual is also suitable for:

Ccd-tr416 Ccd-tr516pk Ccd-tr716 Ccd-tr416pk Ccd-trv16 Ccd-trv16pk ... Show all

Sony CCD-TR315 Service Manual

Service Note

Self-Diagnosis Function

General

Disassembly

Adjustments

Repair Parts List

Quick Links

Related Manuals for Sony CCD-TR315

Summary of Contents for Sony CCD-TR315

This manual is also suitable for:

Table of Contents