PET717/93 TECHNICAL SPECIFICATION General Playback disc type:: DVD-Video, DVD+R/RW, DVD-R/RW, Super VCD, Video CD, DivX4.X-5.X, Audio CD, MP3 CD, JPEG CD, Kodak Dimensions (W x H x D): 199 x158.5 x40 mm Picture CD Bear Unit Weight 0.79kg +/-5% Power supply: Bear Unit Weight: 0.48 kg +/- 5%...
Page 3
2.0 SAFTETY INSTRUCTIONS WAARSCHUWING WARNING Alle IC’s en vele andere halfgeleiders zijn All ICs and many other semi-conductors are gevoelig voor electrostatische ontladingen susceptible to electrostatic discharges (ESD). (ESD). Careless handling during repair can reduce life Onzorgvuldig behandelen tijdens reparatie kan drastically.
2.1 ESD PROTECTION When the power supply is being turned on, you may not remove this laser cautions label. If it removes, radiation of laser may be received. PREPARATION OF SERVICING Pickup Head consists of a laser diode that is very susceptible to external static electrocity. Although it operates properly after replacement, if it was subject to electrostatic discharge during replacement, its life might be shortened.
SAFTY NOTICE SAFTY PRECAUTIONS LEAKAGE CURRENT CHECK Plug the AC line cord directly into a 120V AC outlet (do Measure the AC voltage across the 1500 resistor. not use an isolation transformer for this check). Use an The test must be conducted with the AC switch on and AC voltmeter, having 5000 per volt or more sensitivity.
2.2 SAFETY INSTRUCTIONS Battery Handling Guideline Since the battery is packed in soft package, to ensure its better performance, it’s very important to carefully handle the battery 2.2.1 Soft Aluminium foil The soft aluminum packing foil is very easily damaged by sharp edge parts such as Ni-tabs, pins and needles. Don’t strike battery with any sharp edge parts Trim your nail or wear glove before taking battery Clean worktable to make sure no any sharp particle...
Page 7
Philips Portable DVD Player PET717 POWER ON / OFF/CHR OFF/CHR OPEN • DC IN 12V AV OUT (+/-) CR2025 AUDIO IN CR2025 VIDEO IN CR2025 PHILIPS...
Mechanical and Dismantling Instructions Dismantling Instruction The following guidelines show how to dismantle the player. (The DVD Player should be power off during the dismantling ) Step1: Reverse the set, remove 4 PAD from the Bottom Plate, and remove 7 screws around the Bottom Plate (Figure 1). Figure 1 You can make it throuth the instruction as below for taking tray (Figure 2) Step2:...
Page 13
Mechanical and Dismantling Instructions Dismantling Instruction Step3 : If it is necessary to dismantle Loader or PCB Board, the Mid-CASE moudle should be removed first (Figure 3 & 4). Need remove 1 screw as below figure: Note: Make sure to operate gently otherwise the guider would be damaged. Figure 3 Step4: Disassemble the Mid-CASE: With two hands to open &...
Page 14
Mechanical and Dismantling Instructions Dismantling Instruction Step5: Dismantling the SW Board, should remove 5 screws and disconnect 1 FFC as below Figure5. Figure 5 Step6: Dismanting Loader, disconnect the 2 connectors (XP5, XP6) and 24Pin FFC aiming in the below figure; Dismanting Main Board, remove 4 screws, disconnect other 6 connectors (XP1, XP2, XP7, XP8, XP9, XP10) as below instruction;...
Trouble shooting chart Spindle motor does not move Motor no move Check the FFC connection Correct connection between 24P and the loader. Check whether “RFVCC” Check the RFVCC power (+5V) voltage is normal. supply Check whether laser voltage Check/Replace Q18 Q19. (2.3V for DVD &...
Page 16
Trouble shooting chart The power can not be on The power can’t be on or off Check the output of Replace the adapter or adapter or battery is battery normal. Check whether Check/Correct the U1(oz518) works connection of circuit normaly Check if “SW2”...
Page 17
Trouble shooting chart Disc cannot be read . Disc cannot be read. Check the FFC connection Check the loaded circuit between 24P and the loader. Check whether there is laser Whether peripheral components are voltage (2.3V for DVD and 1.9V eroded or badly soldered.
Page 18
Trouble shooting chart Only DVD disc or only disc except DVD can be played Only DVD disc, or only disc except DVD can be Played. Check Check the loaded circuit connection between 24pin and the loader. Check laser voltage (2.3V) Check the solder status on U3 and output on Collector of Q18 peripheral components...
Page 19
Trouble shooting chart Distorted audio and loud noise Distorted audio and loud noise Check and repair the circuit Check whether the power of U8 supply voltages VGL and VGH VGL and VGH is normal. Check whether Replace R148 and R163 R148 and R163 are normal Check whether the...
Page 20
Trouble shooting chart Abnormal color of video picture Abnormal color of video picture Check whether the Check Y2, C34 and C68 27MHz output signal is normal. Check whether the 3.3V Check the other of supply electric and 1.8V power supply circuit voltages on the decoder board are normal.
Page 21
Trouble shooting chart Remote reception is insensitive or fails. Remote reception is insensitive or fails. Check if the remote Check battery control works properly. Check if the power supply Check R604 voltage remote censor is normal Use an oscilloscope to check if there is output waveform from the first pin IR of Replace IR601...
Page 22
Trouble shooting chart No video picture, no sound. No video picture, no sound. Check whether all the voltages from the IC U1(OZ518) to the Check the loaded circuit CVBS waveform decoder IC are normal. Check if the reset circuit consisting of Replace R86,R87,R89,R90,C86,C88,C89,D14 and R86,R87,R89,R90,C86,C88,C89,D14...
Page 23
Trouble shooting chart No video picture ON TFT No video picture ON TFT CHECK THE CONNECTION OF Correct connection Check and Correct the wrong components in CHECK VOLTAGE OF TFT order to supply the correct voltage CHECK THE SIGNAL ON THE XP703 IS NORMAL Check whether it`s peripheral components are badly soldered,...
Page 24
2) Press <9><6><6>button on the reomote control. name. The software version and other information are display on the TV screen as follows: BE Version: PET717/93.XX (Main version) A. Procedure for software upgrade: FE Version: XXX-XX.XXXXX.XXXXXX_XXXX.XX.XX.XX 1) Power on the set and insert the prepared Upgrade DSP Version: XXX.XX...
Page 32
IR & LED display Board Electric Diagram: IR_VCC PCOM_1 IR601 R601 D600 4.7K R603 LED_RG R604 100R GLED_1 IR_RCV IR DSPVCC33 PCOM_1 R602 C602 RLED_1 C603 XS600 C601 0.1uF 100pF CON8 RLED_1 47uF/16V IR_RCV GLED_1 IR DSPVCC33 GND IR GND IR...
Page 33
Main Board Print-Layout for PET717/93 (Top Side):...
Page 34
Main Board Print-Layout for PET717/93 (Bottom Side):...
Page 35
TFT Board Print-Layout for PET717/93 (Top Side):...
Page 36
TFT Board Print-Layout for PET717/93 (Bottom Side):...
Page 37
Key Board Print-Layout for PET717/93 (Top Side):...
Page 38
Key Board Print-Layout for PET717/93 (Bottom Side):...
Page 39
IR Board Print-Layout for PET717/93 (Top Side):...
Page 40
IR Board Print-Layout for PET717/93 (Bottom Side):...
Page 41
10-1 PET717/93 Mechanical Exploded A1:35 A2:11.14.15.16.17.18.19.21.22.23.25.26 A3:3.6 Remark: It's a general Mechanical Exploded View for TPET717/93, detailed information please refer to Model set.