Page 2
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM- Flash: Flash range (ISO sensitivity and “Memory Stick Duo” media) NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT (Recommended exposure Index) Microphone: Monaural SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES...
Note that formatting permanently erases all data including even protected images. 1-2. DEDICATED A/V CABLE (OPTIONAL ACCESSORY) Dedicated A/V cable is not supplied with this model. For details of the dedicated A/V cable, refer to the “Checking supplied accessories” page. DSC-W510...
Hole Screw Screw Rear Mirror Plate Screw Barrier Tape Screw Barrier Assy Claw Peel off release papers of Barrier Tapes. Install Ornamental Ring A and press it lightly. Ornamental Ring A Barrier Tape Solder Optical Stepping Screw Motor (F1380) DSC-W510...
∗ Tightening torque = 0.049 ± 0.01N•m (0.5 ± 0.1kgf•cm) Flexible Board of 2 Frame Assy Screw Iris Flexible Board Screw Screw Screw DC Motor Worm A Assy Warm B Naruto Gear Lubricated Assy Lubricated Assy Rear Mirror Plate Solder Screw FG Seal Screw DSC-W510...
Page 6
Remove the 2 Group Assy. qj Remove the bond at the three points. qk Rotate 1 Group Lens Assy and remove it from the 1 Group Frame. 2 Group Assy 1 Group Lens Assy Bond 1 Group Frame Fixed Stationary Tube Block DSC-W510...
Page 7
Ditch qa Match three ledges of the 2 Group Assy to three ditches of the Straight Tube Lubricated Assy and install it. Eyepiece Side View Barrier Tape 2 Group Assy Ledge 2 Group Assy Ditch Straight Tube Lubricated Assy DSC-W510...
Page 8
Pass the Flexible Board through the hole of the Fixed Stationary Tube. qh Rotate the Naruto Gear Lubricated Assy and the lens is retractile. Flexible Board Fixed Stationary Tube ws Perform the Flange Back Adjustment after the assembling. DSC-W510...
Page 9
Print at the same magnification (It means 100 % size). Check the settings of printer to print in proper size. • Check of chart size. Make charts together and check if the size of charts is the following size. * The chart consists of 2 pcs. DSC-W510 1-7E...
8 LCD Bracket Assy Front View qs Lens Block Section Right View [Disassembly] [Exploded View] Bottom View 0 Capacitor Cover 6 Ornamental Belt (R) qf Main Frame Assy 3 Front Cover Assy Link DISCHARGING OF THE CHARGING CAPACITOR ACCESSORIES ASSEMBLY DSC-W510...
Page 11
To preparing the short jig, a small clip is attached to each end R:1 k/1 W of a resistor of 1 kΩ /1 W (1-215-869-11). (Part code: 1-215-869-11) Wrap insulating tape fully around the leads of the resistor to prevent electrical shock. Wrap insulating tape. ST Board DSC-W510...
Page 15
NARUTO GEAR LUBRICATED ASSY 4-147-091-01 FRAME, 1 GROUP A-1743-725-A DC MOTOR WORM A ASSY A-1813-018-A CCD BLOCK ASSY A-1743-728-A CAM TUBE BLOCK ASSY A-1743-727-A STRAIGHT TUBE LUBRICATED ASSY 3-086-156-11 SCREW B1.2 1-787-874-11 STEPPING MOTOR, OPTICAL (F1380) 3-947-504-31 SCREW (M1.2) DSC-W510...
Page 16
4-264-983-21 (KOREAN) ∗ 4-264-983-31 (SPANISH, PORTUGUESE) Wrist strap ∗ 4-264-983-41 (ENGLISH, ARABIC, PERSIAN) 2-050-981-01 DSC-W510 User Guide Use this manual if you encounter any problems, or have any questions about the camera. Cyber-shot User Guide (HTML) About Cyber-shot User Guide (HTML) This CD-ROM is provided in HTML.
Page 17
BT Terminal at three points shown below. Soldering point Main Board Assy Top View Pass the Microphone lead wire through the hole of the Main Frame Assy. Main Frame Assy Speaker lead wire Microphone lead wire DSC-W510 3-1E...