Advertisement
SetuP / OPeRatiOn /tech SPecS / waRRanty
Description
The PRO series speaker selectors are highly efficient dual-source, impedance-
matching selectors. These high-quality speaker selectors are designed for use
with either 4-ohm or 8-ohm amplifiers and 4-ohm to 8-ohm speakers.
The PRO speaker selectors are equipped with a low-frequency protection
circuit to reduce subsonic signals. This allows high power operation without
amplifier shutdown. The PRO units employ audiophile-grade impedance
matching autoformers to maintain a safe operating load at the amplifier while
distributing maximum power through the system. Autoformers are very efficient
because of the small loss incurred as a result of heat dissipation. The series is
equipped with a back panel rotary switch, which is used to set the appropriate
impedance based on the number of pairs of speakers connected. This switch
selects the proper taps of the autoformers, allowing all of the amplifier's power
to be delivered to the speakers.
The PRO speaker selectors can be connected to one or two amplifiers. A front
panel button allows switching between the two amplifiers for all speakers
connected to the unit.
Connections
The PRO series have 4-pole screw down removable terminals for speaker and
amplifier connections. These accept wire up to 12 gauge.
Remove the terminal by firmly pulling it out of its 4-pole connector. Strip about
3/8" of insulation from the ends of all wires to be connected. If necessary, twist
the exposed conductor to insure that no loose strands exist. Insert the wire ends
into the screw down connector, being careful to observe proper channel and
polarity. Tighten the screws on the connector. Connect the amplifier(s) and each
pair to the appropriate connector.
If external volume controls are used, connect speaker wire from the appropriate
speaker connector on the PRO to the volume control input. Speaker connections
can support multiple speaker pairs wired in parallel or series, provided their
combined impedance is a minimum of 4 ohms.
Setting System Volume
It is important to properly adjust an impedance-matching system to avoid
distortion or DC clipping (DC voltage will be produced from an amplifier that is
overworked or that has an improper load). These can cause an amplifier/receiver
to go into protection, and can cause autoformers on volume controls to heat
up, damaging system components. To set up the system, the amplifier/receiver
volume should be at its lowest setting, and the selector volume control should
be at the highest setting. Slowly adjust the amplifier/receiver volume to a level
that is acceptable for the amplifier to produce without clipping.
Operation
To ensure safe operation of the amplifier, an impedance level must first be
selected using the rotary switch labeled SPEAKER PAIRS located on the rear of
the unit. This switch should be set to the total number of speaker pairs being
connected to the unit. Set the switch based on the following conditions:
•
If the amplifier and the speakers are both 4 ohms, set the rotary switch to the
number of pairs of speakers connected to the PRO.
•
If the amplifier and the speakers are both 8 ohms, set the rotary switch to the
number of pairs of speakers connected to the PRO.
•
If the amplifier is 8 ohms and the speakers are 4 ohms, set the rotary switch
to TWICE the number of pairs of speakers connected to the PRO.
•
If the amplifier is 4 ohms and the speakers are 8 ohms, set the rotary switch
to HALF the number of pairs of speakers connected to the PRO.
After setting the proper impedance level, the speakers can be turned on and
off in any combination.
To switch between the A and B amplifiers, push the AMP A / AMP B button
located on the front panel.
2
Technical Specifications
Low-Frequency Protection:
Warranty
The Russound PRO Series is fully guaranteed against all defects in materials and
workmanship for ten (10) years from the date of purchase. During this period,
Russound will replace any defective parts and correct any defect in workmanship
without charge for either parts or labor.
For this warranty to apply, the unit must be installed and used according to its
written instructions. If service is necessary, it must be performed by Russound. The
unit must be returned to Russound at the owner's expense and with prior written
permission. Accidental damage and shipping damage are not considered defects,
nor is damage resulting from abuse or from servicing by an agency or person not
specifically authorized in writing by Russound.
This Warranty does not cover:
•
Damage caused by abuse, accident, misuse, negligence, or improper installation
or operation
•
Power surges and lightning strikes
•
Normal wear and maintenance
•
Products that have been altered or modified
•
Any product whose identifying number, decal, serial number, etc. has been
altered, defaced or removed.
Russound sells products only through authorized Dealers and Distributors to
ensure that customers obtain proper support and service. Any Russound product
purchased from an unauthorized dealer or other source, including retailers, mail
order sellers and online sellers will not be honored or serviced under existing
Russound warranty policy. Any sale of products by an unauthorized source or other
manner not authorized by Russound shall void the warranty on the applicable
product.
Damage to or destruction of components due to application of excessive power
voids the warranty on those parts. In these cases, repairs will be made on the basis of
the retail value of the parts and labor. To return for repairs, the unit must be shipped
to Russound at the owner's expense, along with a note explaining the nature of
service required. Be sure to pack the unit in a corrugated container with at least
three (3) inches of resilient material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at (603) 659-5170 for a Return
Authorization number. Write this number on the shipping label and ship to:
Russound, ATTN: Service, 5 Forbes Road, Newmarket, NH 03857
Due to continual efforts to improve product quality as new technology and
techniques become available, Russound/FMP, Inc. reserves the right to revise system
specifications without notice.
Russound PRO Series Installation Manual
Power:
100 watts per channel RMS continuous
200 watts per channel average
300 watts per channel peak
Impedance Matching:
High-efficiency impedance-matching
autoformers
Bi-polar capacitor circuit
Wire Size:
up to 12 gauge wire
Dimensions:
17" W x 2.875" H x 8.25" D (43.2 x 7.3 x 21 cm)
Weight:
PRO-6 7.52 lbs. (3.4 kg)
PRO-8 7.75 lbs. (3.49 kg)
PRO-12 7.995 lbs. (3.58 kg)
Rev. 5
Advertisement
