Factory Settings Screen; Others Troubleshooting; Specifications - JVC TK-WD310 Instructions Manual

Allowed characters
direction (SELECTOR button)
Space
Pressing the SELECTOR button in the
character on the right and pressing in the
character on the left. Pressing and holding the button will continu-
ously change the character selected.
Memo
When CAMERA TITLE is set to ON, a background the width of 1
character is displayed, even when there is no camera title entered.
If a CAMERA TITLE of more than 1 character is entered, a back-
ground the width of 24 characters is displayed.
38
OTHERS
Troubleshooting
Symptom
The operation becomes un- Drop in voltage of the power supply can
be considered. Check the length and
stable
thickness of the power supply cable.
(
Set the VIDEO/DC switch on the side
The auto iris will not operate
of unit according to the type of auto iris
lens used.
(
There is noise in the screen Lower the gain using the AGC MODE
or increase in residual im- menu item.
ages ULTRA SUPER HIGH
(MAX)
(
The colors of the screen are When using in an environment where
not natural there are changes in the light source,
set the WHITE BALANCE menu item
to ATW.
(
Set the WHITE BALANCE menu item
White balance adjusted
automatically/manually to AWB or MANUAL.
cannot be used (
The camera title will not ap- Set the CAMERA TITLE menu item to
pear ON.
(
The vertical phase cannot be When adjusting the vertical phase dur-
adjusted using the V PHASE ing line lock, set the LL/INT switch on
menu item the back of unit to LL.
(
40
direction
direction will select the
direction will select the
Remedy
Page 17)
Pages 20, 21)
MID LOW OFF
(MIN)
Gain
Page 31)
Page 33)
Page 33)
Page 36)
Page 11)
MENU SETTING

FACTORY SETTINGS screen

Returns set values to their factory settings.
1.
— — — — — —
ME N U
F OC U S A D J U S T . .
2.
V I D E O A D J U S T . .
C AM E R A S E T T I N G S . .
F A C T O R Y S E T T I N G S . .
E X I T
3.
Cursor
— — — F A C T OR Y S E T T I N G S — — —
C A N C E L
C L E A R
4.
OTHERS

Specifications

Image pickup device : 1/3 type WDR digital image device
Number of effective pixeis : 380,000 pixels ((H) 720 × (V) 540)
Synchronizaton method : Internal,Line lock
Scanning frequency : U Type (H) 15.734 kHz, (V) 59.94 Hz
E type (H) 15.625 kHz, (V) 50.0 Hz
Resolution : 480 TV lines (H)
VIDEO OUT : Composite video signal
1 V(p-p), 75Ω (BNC)
Video S/N ratio : 50 dB (AGC OFF)
Minimum required illumination : 1.9 lx (50%, F1.2, AGC HIGH)
0.5 lx (50%, F1.2, AGC ULTRA(×16))
0.95 lx (25%, F1.2, AGC HIGH)
0.25 lx (25%, F1.2, AGC ULTRA(×16))
Lens mount : CS mount
Power supply : AC 24 V
DC 12 V
Power consumption : U type Approx. 5.7 W
E type Approx. 400 mA
Ambient temperature : –10°C to 50°C (operation)
0°C to 35°C (recommended)
Mass : 330
Accessory : Instructions
U type .............................. 1
E type .............................. 2
Ferrite core ....................... 1
External Dimensions (Unit: mm)
U1-32
50
TRIPOD
BASE
Design and specifications are subject to change without notice.
Operation
Display the FACTORY SET-
TINGS screen. ( Page 24)
Press the SELECTOR button in
the vertical direction ( or )
and move the cursor (>) to
CLEAR.
Press the SET button.
● Settings including the camera
title will be restored to the fac-
tory settings and the screen
will return to the MENU screen.
Select CANCEL and press the
SET button to return to the
MENU screen without chang-
ing settings.
Exit the menu screen.
Select EXIT within the MENU
screen and press the SET but-
ton to return to the normal screen.
39
50 Hz/60 Hz
107
95
COLOR VIDEO CAMERA
1/4-20UNC
33
MOUNTING HOLE
41