Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for NA OMEGA W
-
Page 2: Table Of Contents
TABLE OF CONTENT 1. BEFORE YOU BEGIN What is included Unpacking Power Contact us Safety Instructions 2. INTRODUCTION Device description Product owerveiw Features 3. SETUP Installation Guide Specification of system OMEGA Setup Power suply Power requirements Cooling OMEGA dimmer package Check transportation damage Package content Instalation... -
Page 3: Before You Begin
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch. Contact us General Information Company NA 9 Lambertu str. Marupe, LV-2167, Latvia Phone: +371 6780 1111... -
Page 4: Safety Instructions
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact „Company NA” at: +371 6780 1111. Omega Dimmer series User manual version 1.0... -
Page 5: Introduction
NTRODUCTION Device description The OMEGA, OMEGA+ and OMEGA W are a "Company NA" manufactured dimmers. The Omega series dimmers are designed for controlling incandescent lamp brightness. The dimmers has 12 or 24 output channels. Its operating principle is based on triac ignition phase regulation. - Page 6 OMEGA + - rackmount 12 channel dimmer owerveiw OMEGA and OMEGA + - rackmount back panel owerveiw Omega Dimmer series User manual version 1.0 09.2011...
- Page 7 OMEGA W - wallmount 24 channel dimmer owerveiw Omega Dimmer series User manual version 1.0 09.2011...
-
Page 8: Features
Features ● 12 or 24 output channels ● Control: DMX-512 or Manual settings ● Maximum output power per channel 4.0 kW ● Rated output power per channel 1.0 kW ● Maximum Current 63A per phase ● Power Protection Type - automatic switch (C-curve) ●... -
Page 9: Power Requirements
Maximum fuse (switches) Dimensions: 125A D-type auto fuse or equivalent (which Mono frame, with or without mains isolators may be a fuse switch) Double frame system without mains 250A D-type auto fuse or equivalent (which isolators may be a fuse switch) Double frame system is equipped with 160A D-type auto fuse or equivalent (which mains isolators... -
Page 10: Starting The System
yellow blue black green/yellow Phase L1 Phase L2 Phase L3 neutral earth Complete DMX cable plug Connect the DMX input/output sockets on the back of the hull Unplug power before service. Always use the same type of parts for service. Starting the system Check incoming power cords Check the incoming wires are connected properly and securely tightened,... -
Page 11: Operating Instructions
4. O PERATING NSTRUCTIONS Manual Control On the front panel of hull is placed 4-way buttons - [UP] [DOWN] [LEFT] [RIGHT] and approval or menu button - [MENU]. To serve numerical values of the input use rotary encoder. All activities are reflected in the 16x2 character display. Dimmer operates three basic regime - the base screen mode, the test sub menu and service functions. - Page 12 [UP] - Look aditional information about Omega dimmer system. Frequency and Voltage in each phase: "F = 50.00 Uabcs=" "220 223 229 8" Fan seed and teperature of radiator: nc. - breakege of temperature sensor, sc. - temperature sensor short circuit. "Fan speed = 100%"...
- Page 13 Shows value of channel our group 0 - 255 User MENU setup. enter Press and hold [MENU] button for 3 seconds to USER MENU SETUP "DMX address set" - DMX address setup. For numerical parameter setup, use rotary encoder, or buttons [UP] and [DOWN] - addresses changes in the value of + / - 1.
-
Page 14: Technical Setup Menu
c # 5 s + 1 0 Chase speed selection 0 - +/-99 "Background" – Setup background channel levels. Works together with "Chase" function, HTP. Number of controllable channel Channels (c) or channel group (G) label. Controllable channel level 0-255. "Exit"... -
Page 15: Engineering Menu, Default Settings
limits from 50 to 100%. "Patch" - DMX channel setup for each output channel individually. Use buttons and encoder to asigne each output a specific DMX address: Example: "Output 7" "DMX in 401" "Lamp Dynamic" - a lamp on / off time settings. For lamp life increasing. Settings are set equal for all output channels: - for DMX Control from DMX input, - for test mode,... - Page 16 "= 3 min " -default. "Phase sequence" - Output Channels connected to phase setup. Specifies in what order the phases are connected to the channels: Example: AAAABBBBCCCC; ABCABCABCABC - default ; AAAAAAAAAAAA. "DMX unplug" - DMX input signal is lost setup. Allows you to select the state, which occurs when DMX signal is lost: "Blackout"...
-
Page 17: Appendix
5. Appendix DMX-512 Protocol DMX-512 protocol has 512 channels universs. Channels (adress) can committed in any way depending on the device. To operate equipment with DMX-512 protocol is necessary one channel or multiple channels in a row depending on type of device. User sets up the address of the equipment, which coincides with the light control panel installed. -
Page 18: Maintenance
Do not allow contact between the common and the fixture’s chassis CAUTION ground. Grounding the common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other. 3-PIN TO 5-PIN CONVERSION CHART NOTE ! If you use a console with a 5 pin DMX output connector, you will need to use a... -
Page 19: Returns Procedure
Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #). Products returned without an RMA # will be refused. Call Company NA and request RMA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. - Page 20 OMEGA Technical Specification WEIGHT & DIMENSIONS Length ......................482.6 mm Width ......................400 mm Height ......................133.2 mm Weight .......................26.2 kg Body .......................19' rackmount POWER Input Voltage ................220V AC, 3 phase Input Plot ...................L1 + L2 + L3 + N + E Power Outputs ..................
- Page 21 OMEGA + Technical Specification WEIGHT & DIMENSIONS Length ......................482.6 mm Width ......................400 mm Height ......................133.2 mm Weight .......................26.6 kg Body .......................19' rackmount POWER Input Voltage ................220V AC, 3 phase Input Plot ...................L1 + L2 + L3 + N + E Power Outputs ..................
- Page 22 OMEGA W Technical Specification WEIGHT & DIMENSIONS Length ......................566.0 mm Width ......................133.0 mm Height ......................762.0 mm Weight .......................35.1 kg Body ......................wallmount POWER Input Voltage ................220V AC, 3 phase Input Plot ...................L1 + L2 + L3 + N + E Power Outputs ..................