Page 1
LCD-TV Chassis : N84A Model : LA37C630* LA32C650* LA40C630* LA37C650* LA46C630* LA40C650* LA55C630* LA46C650* LA55C650* LA60C650* SERVICE Manual TFT-LCD TV Contents 1. Precautions 2. Product specifications 3. Disassembly and Reassembly 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram LC630 / LC650 Refer to the service manual in the GSPN (see the rear cover) for the more information.
3. Disassembly and Reassembly 3. Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the LE32C650L1WXXC LCD TV. WARNING: This LCD TV contains electrostatically sensitive devices. Use caution when handling these components. 3-1. Disassembly and Reassembly Cautions: 1.
Page 5
3. Disassembly and Reassembly Description Picture Description Screws 3. Lift up the rear-cover. 4. Remove the screws of IP and main board. 6001-002284 (M4, L6, Machine) 5. Remove the speakers and screws of inlet socket. 6001-002284 (M4, L6, Machine) 6001-002284 (M4, L6, Machine)
Page 6
3. Disassembly and Reassembly Description Picture Description Screws 6. Remove the screws of Stand BKLT. Lift up the Stand BKLT. 7. Remove the Side AV Ass’y. (only 46”)
Page 7
3. Disassembly and Reassembly Description Picture Description Screws 8-1. Remove the screws of bracket. (32”) 8-2. Remove the screws of bracket. (40”) Reassembly procedures are in the reverse order of disassembly procedures. ※...
1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-4. Installation Precautions For safety reasons, more than a people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
2. Product specifications 2-2. Specification Comparison to Old Models LC630 Arsenal/Valencia Arsenal/Chelsea Model (LE40C630) (LE40B65*) Design Display Type LCD TV LCD TV Built-in Tuner Resolution 1920 x 1080 1920 x 1080 LCD Panel TFT LCD Panel 100Hz FULL HD TFT LCD Panel 100Hz FULL HD Screen Size 32''/37''/40''/46''/55''/60''...
Page 50
2. Product specifications PAL On-Air Channel Frequence Table Europe INDONESIA IRELAND South Africa ANGOLA NEWZEALAND ITALY channel PAL-BG PAL-BG PAL-I PAL-I PAL-I PAL-BG PAL-BG 53.75 62.25 82.25 175.25 183.75 192.25 201.25 210.25 217.25 224.25 44.25 45.75 43.25 45.25 48.25 55.25 53.75 52.25...
2. Product specifications 2-3. Movie Plus: MJC(Motion Judder Cancellation) Technology Example • Motion Judder cancellation for HD film image. • Adaptive Recursive Search (ARS) - Implementation IPC/MJC at same time <Motion Judder> - Search Range Horizontal : ± 72 Pixel, Vertical : ±...
2. Product specifications 2-5. Light Sensor Light sensor is used to measure the ambient light level in the enviroment as perceived by the human eye. It is designed to detect bright and dim ambient light conditions as a means of controlling the brightness of a LCD display and /or keypad.
Yes: If the test pattern does not appear or there is noise in the test pattern, select Yes. There may be a problem with the TV. Therefore, contact Samsung’s call centre for assistance. Yes: If the test pattern is properly displayed, select No. There may be a problem with your external equipment.
4. Troubleshooting 4-1-1. No Power The LEDs on the front panel do not work when connecting the power cord. The SMPS relay does not work when connecting the power cord. Symptom The units appears to be dead. The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are improperly connected or the Main Board or SMPS is not functioning.
4. Troubleshooting 4-1-2. No Video (Analog PC signal) Symptom Audio is normal but no picture is displayed on the screen. Check the PC source Major Check the IC6001(SDP84) checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Power Indicator is off.
Page 61
4. Troubleshooting WAVEFORMS R, G, B, H_sync input signal of IC6001(SDP84)
Page 62
4. Troubleshooting 4-1-3. No Video (HDMI - Digital Signal) Symptom Audio is normal but no picture is displayed on the screen. Check the HDMI source Major Check the IC3013 checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Power Indicator is off.
Page 63
4. Troubleshooting WAVEFORMS Digital Output Data Signal of HDMI(Data)
Page 64
4. Troubleshooting 4-1-4. No Video (Tuner_CVBS) Symptom Audio is normal but no picture is displayed on the screen. Check the Tuner CVBS source Major Check the IC6001(SDP84) checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Power Indicator is off.
Page 66
4. Troubleshooting 4-1-5. No Picture (Video_CVBS) Symptom Audio is normal but no picture is displayed on the screen. Check the Video Source Major Check the IC6002, IC6001(SDP84), IC7001 checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Power Indicator is off.
Page 67
4. Troubleshooting WAVEFORMS CVBS Output Signal at C6852, C6853, C6854 4-10...
4. Troubleshooting 4-1-6. No Sound Symptom Picture is normal But no Sound Check the RF Source Major Check the IC6001(SDP84) checkpoints This may be happened when LVDS Cable is Connected between Panel and Main Board , But Sound cable is disconnected. Connect a sound cable.
Page 69
4. Troubleshooting WAVEFORMS The Signal are Inputed to IC2002 The Signal are Inputed to IC2002 4-12...
Page 70
4. Troubleshooting 4-1-7. Defect Analysis ahead of models. Defective image / Defective Symptoms Check & Solution No Picture and normal sound. Check the LVDS cable insert correctly. in case of defective a Panel or a defective connector between main board and panel. 4-13...
4. Troubleshooting 4-2. Alignments and Adjustments 4-2-1. General Alignment Instuction Usually, a color LCD-TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. Use the specified test equipment or its equivalent. Correct impedance matching is essential.
4. Troubleshooting 4-3. Factory Mode Adjustments 4-3-1 Entering Factory Mode To enter ‘Service Mode’ Press the remote -control keys in this sequence : - If you do not have Factory remote - control INFO MENU MUTE Power on - If you have Factory remote - control PICTURE ON INFO FACTORY...
4. Troubleshooting 4-3-3 Factory Data Option Item Range OPTION Factory Reset Inch Vendor(A:AMLCD, D:CMO, L:AUO, I:CPT) Panel frequency (6:50/60Hz, 1:100/120Hz, 2:200/240Hz) Panel(A:AG, T:TN, U:UC) Select Type Resolution(F:FHD, H:HD, U:UD) Panel Type Panel 1st/2nd(1st:0, 2nd:1) BLU (C:CCFL, L:LED, E:EDGE LED) ex) 32D1UF0E : Vendor : CMO inch : 32 120Hz FHD U/C Edge LED panel Local Set EU, EU_Italy, EU_Africa, EU_Israel, NORDIG, AD_Au, CIS...
Page 74
4. Troubleshooting Control Item Range EDID EDID ON/OFF EDID WRITE ALL SUCCESS EDID WRITE PC SUCCESS EDID WRITE HDMI SUCCESS EDID WRITE HDMI1 … EDID WRITE HDMI2 … EDID WRITE HDMI3 … EDID WRITE HDMI4 … EDID 1.2PORT NONE,Not Support NONE, W-Milky, T-M-Brn, T-W-Brn, T-W-Gray, W-D-Gray, W-M-Whit Front Color W-Violet, T-C-Gray, T-R-BLK, S-BLK, S-C-Gray...
Page 75
4. Troubleshooting Item Range Hotel Option HOTEEL MODE POWER ON CHANNEL POWER ON BAND POWER ON VOLUME MAX VOLUME PANEL BUTTOM LOCK POWER ON SOURCE Item Range Shop Option Shop Mode USB DEMO ON(SEC) USB DEMO OFF(SEC) Item Range Test for input Scaler.
Page 76
4. Troubleshooting Advanced Item Range FEB3 BM_slope BM_start BM_stat_max Lfunc_gain Hfunc_gain ACR-Offset Skin-UV FEB Sub color M-skin-UV M-Sub Color N_Skin_UV N_Sub_Gamma Color Gamut LFUNC_TH1 LFUNC_TH2 LFUNC_TH3 LFUNC_OUT2 LFUNC_OUT3 LFUNC_OUT4 LFUNC_OUT5 UFUNC_TH1 UFUNC_TH2 UFUNC_TH3 UFUNC_OUT2 UFUNC_OUT3 UFUNC_OUT4 UFUNC_OUT5 PPHC_Red PPHC_Green PPHC_Blue PPHC_Cyan PPHC_Magenta...
Page 77
4. Troubleshooting Item Range WB Movie W/B Movie ON/OFF ON/OFF MODE Dynamic/Movie/Natural Color Tone Cool/NORMAL/WARM1/WARM2 MSub Brightness Msub Contrast N_Rgain N_Bgain N_Roffset N_Boffset W1_Rgain … W1_Bgain … W1_Roffset … W1_Boffset … W2_Rgain … W2_Bgain … W2_Roffset … W2_Boffset … Movie Contrast Movie Bright Movie Color Movie Sharpness...
Page 78
4. Troubleshooting Item Range ColorMapping Auto_Red_R Auto_Red_G Auto_Red_B Auto_Green_R Auto_Green_G Auto_Green_B Auto_Blue_R Auto_Blue_G Auto_Blue_B Auto_Yellow_R Auto_Yellow_G Auto_Yellow_B Auto_Cyan_R Auto_Cyan_G Auto_Cyan_B Auto_Magenta_R Auto_Magenta_G Auto_Magenta_B Item Range EPA 3D Standard Contrast Standard Brightness Standard Sharpness Standard Color Standard Tint Standard Backlight 3D Contrast 3D Brightness V_3D PWM Delay_60 V_3D ANA Delay_60...
4. Troubleshooting 4-4. White Balance - Calibration 4-4-1 White Balance -Calibration AV Calibration ADC/WB Comp Calibration PC Calibration HDMI Calibration 4-4-2 Service Adjustment You must perform Calibration in the Lattice Pattern before adjusting the White Balance. Color Calibration Adjust spec. 1.
Page 87
4. Troubleshooting Method of Color Calibration (AV) 1) Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port 2) Press the Source key to switch to “AV1” mode 3) Enter Service mode 4) Select the “Calibration” menu 5) Select the “AV Calibration”...
4. Troubleshooting 4-4-3 White Balance - Adjustment (low light) (hight light) Sub Bright Sub Contrast 3. W/B R offset R gain G offset G gain B offset B gain (W/B adjustment Condition refer next page) 4-5. White Ratio (Balance) Adjustment You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
4-6. Servicing Information 4-6-1 USB Download Method Samsung may offer upgrades for TV’s firmware in the future. Please contact the Samsung call center at 1-800- SAMSUNG (7267864) to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on located on the back of your TV.
Page 90
4. Troubleshooting 2. To enter User menu Support - Software Upgrade - By USB then press the ENTER button. The message USB searching... It may take up to 30 seconds is displayed. Please be careful to not disconnect the power or remove the USB drive while upgrade is being applied.
6. Wiring Diagram 6-2. Wiring Picture 6-3. Connector Functions Connector Functions Panel CN1901 The LVDS signal transfered Panel to Main Board. * defective symptom : No pcture but normal sound Supply dimming and main power from IP,SMPS to Main Board. SMPS ...