Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DWE46101
Summary of Contents for DeWalt DWE46101
- Page 1 DWE46101 www.
- Page 2 Figure 1 Figure 2...
- Page 3 Figure 3 Figure 4 Figure 5...
- Page 4 Figure 6 Figure 7 Figure 8...
-
Page 5: Technical Data
EN GLI SH MORTAR RAKING KIT DWE46101 An estimation of the level of exposure to Congratulations! vibration should also take into account You have chosen a D WALT tool. Years of the times when the tool is switched off experience, thorough product development and... -
Page 6: Ec Declaration Of Conformity
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed DWE46101 (grounded) power tools. Unmodified plugs WALT declares that these products described and matching outlets will reduce risk of under Technical Data are in compliance with: electric shock. -
Page 7: Safety Instructions For All Operations
EN GLI SH Remove any adjusting key or wrench working conditions and the work to before turning the power tool on. A be performed. Use of the power tool for wrench or a key left attached to a rotating operations different from those intended part of the power tool may result in personal could result in a hazardous situation. -
Page 8: Causes And Operator Prevention Of Kickback
EN GL IS H damage or install an undamaged accessory. p) Do not use accessories that require liquid After inspecting and installing an accessory, coolants. Using water or other liquid coolants position yourself and bystanders away from may result in electrocution or shock. the plane of the rotating accessory and run FURTHER SAFETY INSTRUCTIONS the power tool at maximum no-load speed... -
Page 9: Safety Warnings Specifi C For Grinding And Abrasive Cutting-Off Operations
EN GLI SH e) Do not attach a saw chain woodcarving from the cut while the wheel is in motion blade or toothed saw blade. Such blades otherwise kickback may occur. Investigate create frequent kickback and loss of control. and take corrective action to eliminate the cause of wheel binding. -
Page 10: Residual Risks
(opens and allows cutting of an inside corner) n. Clamp lever Wear eye protection. INTENDED USE The DWE46101 heavy-duty slot cutter has been DATE CODE POSITION (FIG. 1) designed for professional cut-off applications. The date code (o), which also includes the year of Your mortar raking shroud has been designed manufacture, is printed into the housing. -
Page 11: Electrical Safety
EN GLI SH use of the mortar raking shroud could otherwise Electrical Safety contaminate the working environment or pose an The electric motor has been designed for one increased health risk to the operator and those in voltage only. Always check that the power supply close proximity. - Page 12 8. Close and secure the cornering door (m) by NOTE: The supplied mortar raking shroud is only tightening the cornering door locking lever (l). recommended for use with the DWE46101 heavy- duty mortar raking motor. 9. To remove the disc, loosen the threaded clamp nut (e) with the two-pin spanner.
-
Page 13: Prior To Operation
EN GLI SH 2. Turn cornering door locking lever (l) • Be sure the inner and outer flanges are counterclockwise one full rotation. Grasp the mounted correctly. corner door (m) and rotate open. • Make sure the disc or wheel rotates in the 3. -
Page 14: Maintenance
EN GL IS H as the activation of a ground fault WARNING: Hold the side handle and interrupter, throwing of a circuit breaker, body of the tool firmly to maintain accidental unplugging, or power failure. control of the tool at start up and during If the switch is locked on when the use and until the wheel or accessory power is connected, the tool will start... -
Page 15: Protecting The Environment
EN GLI SH reconnecting the tool, depress and Protecting the Environment release the switch to ensure that the Separate collection. This product must tool is off. not be disposed of with normal household waste. Pop-off Brushes The motor will be automatically shut off indicating that the carbon brushes are nearly worn out and Should you find one day that your D WALT product... - Page 16 EN GL IS H GUARANTEE WALT is confident of the quality of its products and offers an outstanding guarantee for professional users of the product. This guarantee statement is in addition to and in no way prejudices your contractual rights as a professional user or your statutory rights as a private non-professional user.
- Page 17 EN GLI SH CUTTING ACCESSORY CHART Guard Type Accessory Description How to Fit Grinder Masonry cutting disc, bonded TYPE 1 Type 1 guard GUARD Metal cutting disc, bonded Backing flange Diamond Cutting wheel cutting wheels Threaded clamp nut...