Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AOC FT700
Summary of Contents for AOC FT700
- Page 1 FT700 17” Flat CRT User’s Manual By Envision Peripherals, Inc. www.aocmonitor.com...
- Page 2 Thank you very much for choosing the AOC Color Monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.
- Page 3 FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 4 PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.
- Page 5 Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
-
Page 6: Technical Support(Faq)
*Check if the PC System is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are available at: www.aocmonitor.com) Picture is fuzzy *Adjust the Contrast and Brightness Controls. -
Page 7: Power Cord
INSTALLATION INSTRUCTIONS SWIVEL BASE To attach the swivel base to the monitor, do the following: • Carefully turn the monitor on its side or upside down. (see figure 1) • Locate the cavities at the bottom front of the monitor. •... - Page 8 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS The other control knobs are located at the base of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. •...
- Page 9 Figure 1: Installing and Removing the Swivel Base Figure 2: Connecting Cables Figure 3: External Controls Figure 4: The OSD Menu 1024 × 768 Signal Cable Power Cord VGA Card Connector Power ON/OFF Switch Power Indicator Menu Contrast/Right Brightness/Left Exti...
- Page 10 FRONT PANEL CONTROL (see figure 3) NT PANEL CONTROL • Power ON/OFF Switch: Press this key to switch the display ON or OFF. • Power Indicator : Green — Power On mode. Orange — Off mode. • MENU : Press this key to either bring up the OSD menu or select an item on the menu.
-
Page 11: Select Language
ADJUSTING THE PICTURE (see figure 4) CONTRAST BRIGHTNESS H- CENTER H- SIZE V- CENTER V- SIZE ZOOM PINCUSHION TRAPEZOID PIN-BALANCE PARALLELO- GRAM ROTATION 6500°K/9300°K ( COLOR TEMPERATURE ) USER COLOR ( Red / Blue ) DEGAUSS MOIRE REDUCE RECALL EXIT SELECT LANGUAGE Adjust the picture contrast. - Page 12 SPECIFICATION 21mm(H), 0.25mm(D) dot pitch Viewable Image Size Video Separate Sync. H/V-sync.: Scanning Frequency: Horizontal Vertical Max. Resolution Video Dot Rate Factory Preset Timings : User mode Timings : Power Source Operating Humidity Dimension Weight Signal Cable Plug & Play ≤...
-
Page 13: Horizontal Frequency
Preset Timing Table STANDARD RESOLUTION 720 x 400 640 x 480 VESA/85 640 x 480 VESA/85 800 x 600 VESA/85 1024 x 768 VESA/60 1280 x 1024 Connector Pin Assignment PIN NO. HORIZONTAL FREQUENCY 31.5kHz 31.5kHz 43.3kHz 53.7kHz 68.7kHz 64.0kHz PIN NO.