Mackie SP260 Owner's Manual page 8

Passive
Subwoofer
CHANNEL 2 BRIDGED
POWER CONSUMPTION
2000 W
SPEAKER OUTPUTS
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE Use only class 3 wiring
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
PIN PIN
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION. 1+ BRIDGED 1+
1 2+
AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
AVIS: N'OUVREZ PAS LA COUVERTURE. N'EXPOSEZ PAS CET ÉQUIPEMENT À LA
PLUIE OU À L'HUMIDITÉ.
PIN
CH 2 2+ 1+ CH 1
2 1
Mackie FRS Power Amplifier (for subs)
Here's a fun setup! In this example, the SP260 is configured using the '2x2Way+Subs' setup type.
The left and right line-level 1/4" outputs from a Mackie 1604-VLZ3 mixer feed the A and B XLR inputs
of a Mackie SP260 Speaker Processor. XLR outputs 1 and 2 of the Mackie SP260 Speaker Processor
feed the 1 and 2 XLR inputs of a Mackie FRS Power Amplifier. The CH 1 and CH 2 NL4 speaker outputs
of the power amplifier feed the high inputs of two bi-amplified passive loudspeakers.
XLR outputs 3 and 4 of the Mackie SP260 Speaker Processor feed the 1 and 2 XLR inputs of
another Mackie FRS Power Amplifier. The CH 1 and CH 2 NL4 speaker outputs of this power
amplifier feed the low inputs of the two aforementioned bi-amplified passive loudspeakers.
XLR outputs 5 and 6 of the Mackie SP260 Speaker Processor feed the 1 and 2 XLR inputs of a third
Mackie FRS Power Amplifier. The CH 1 and CH 2 NL4 speaker outputs of this power amplifier feed input
A of two passive subwoofers.
The SP260's high- and low-pass filters on the output channels are configured to create a crossover
so that outputs 1 and 2 of the SP260 deliver the high frequencies to the loudspeakers, outputs 3 and 4
deliver the low frequencies to the same loudspeakers and outputs 5 and 6 deliver the lowest frequencies
to the passive subwoofers. The subs may be stereo or mono by properly configuring the input sources for
SP260 outputs 5 and 6.
Bi-amped Passive Full-Range Loudspeakers with Subwoofers
8
SP260 2x6 Speaker Processor
Passive Mackie FRS
Subwoofer Power Amplifier
(for lows)
CHANNEL 1
FILTER
SUBSONIC @ 30Hz
CLIP LIMIT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
PIN
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
1+ THAT MAY CAUSE UNDESIRED OPERATION.
1
AMP MODE
AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
AVIS: N'OUVREZ PAS LA COUVERTURE. N'EXPOSEZ PAS CET ÉQUIPEMENT À LA
PLUIE OU À L'HUMIDITÉ.
Mackie SP260
ON
Speaker Processor
100-240 VAC
40W 50/60 Hz
FUSE: T 800mAL 250V
To Low In
Bi-ampable Passive
Loudspeaker
CHANNEL 2 BRIDGED CHANNEL 1
POWER CONSUMPTION
2000 W
SPEAKER OUTPUTS
Use only class 3 wiring
PIN PIN PIN
1+ BRIDGED 1+ 1+
1 2+ 1
PIN
CH 2 2+ 1+ CH 1
2 1
ATTENTION: RISK OF ELECTRIC SHOCK
DO NOT OPEN THE COVER
MAIN
LIFT GND
6 5 4 3 2 1
OUTPUTS
Mackie
1604-VLZ3
Mixer
To High In
To Low In
CHANNEL 2
FILTER
SUBSONIC @ 30Hz
POWER CONSUMPTION
2000 W
CLIP LIMIT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
AMP MODE
AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
AVIS: N'OUVREZ PAS LA COUVERTURE. N'EXPOSEZ PAS CET ÉQUIPEMENT À LA
PLUIE OU À L'HUMIDITÉ.
Mackie FRS Power Amplifier (for highs)
PUSH PUSH
B A
INPUTS
A / B Inputs
L / R Line Level Outputs
To High In
Bi-ampable Passive
Loudspeaker
BRIDGED CHANNEL 1
FILTER
SUBSONIC @ 30Hz
SPEAKER OUTPUTS CLIP LIMIT
Use only class 3 wiring
PIN PIN PIN
1+ BRIDGED 1+ 1+
1 2+ 1
AMP MODE
PIN
CH 2 2+ 1+ CH 1
2 1