DVD PLAYER OWNER’S MANUAL MODEL : SD-K625 SD-2815 Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.
Safety Precautions FCC WARNING: This equipment may generate or use radio CAUTION frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifi- RISK OF ELECTRIC SHOCK DO NOT OPEN cations are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an CAUTION: TO REDUCE THE RISK unauthorized change or modification is made.
IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND 15. Attachments INSTRUCTIONS IN THIS OWNER’S MANUAL AND THOSE Only use attachments/accessories specified by the manufacturer. MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR 16. Accessories FUTURE REFERENCE. Use only with the cart, stand, tripod, bracket, or This set has been designed and manufactured to assure personal safety.
Before Use Playable Discs Disc-related terms Title (DVD only) The main film content or accompanying feature content DVD Video or additional feature content, or music album. (8 cm / 12 cm disc) Each title is assigned a title reference number enabling Video CD (VCD) you to locate it easily.
Before Use (Cont’d) Precautions Storing discs After playing, store the disc in its case. Handling the unit Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct sun- When shipping the unit light, as there may be a considerable temperature build- The original shipping carton and packing materials...
Front Panel and Display Window ON/STANDBY PLAY ( Switches the player ON and OFF. Starts playback. OPEN/CLOSE ( ON/STANDBY indicator Opens or closes the disc tray. Lights red when the player is in Standby mode (off). 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 STOP ( (left/right/up/down) Stops playback.
Page 11
Remote Control POWER OPEN/CLOSE ( Switches DVD Player ON and OFF. Opens and closes the disc tray. ZOOM GUI DISPLAY Enlarges video image. Accesses on-screen display E.A.M. SETUP Selects sound mode during disc Accesses or closes setup menu. playback. TOP MENU MENU Displays the Title menu of the disc if Accesses menu on a DVD disc.
Rear Panel OPTICAL (Digital audio out jack) Connect to digital (optical) audio equipment. COAXIAL (Digital audio out jack) Connect to digital (coaxial) audio equipment. ANALOG AUDIO OUT (Left/Right) 1, 2 Connect to an amplifier, receiver or stereo system. AC Power Cord Plug into the power source.
Connections Rear of TV Tips Depending on your TV and other equipment you wish S-VIDEO COMPONENT VIDEO / VIDEO AUDIO INPUT PROGRESSIVE SCAN INPUT INPUT INPUT to connect, there are various ways you could connect the player. Use only one of the connections described below.
Connections (Cont’d) Connecting to Optional Equipment Rear of DVD player Connecting to an amplifier equipped with two channel analog stereo or Dolby Surround Connect the Left and Right AUDIO OUT jacks on the DVD Player to the audio left and right in jacks on your amplifier, receiver or stereo system, using the supplied audio cables (A).
Before Operation General Explanation Repeat mode Icons Repeat Title This manual gives basic instructions for operating the TITLE DVD Player. Some DVDs require specific operation or Repeat Chapter CHAPT allow only limited operation during playback. When this Repeat Track (non-PBC Video CDs TRACK occurs, the symbol appears on the TV screen, indi-...
Before Operation (Cont’d) Initial Settings Menu Language Select a language for the setup menu. This is the menu You can install your own Personal Preferences. you see when you press SETUP. Initial Settings General Operation English Disc Audio Disc Subtitle Spanish Press SETUP.
Page 17
Before Operation (Cont’d) Sound Dynamic Range Control (DRC) With the DVD format, you can hear a program’s sound- Digital Audio Output track in the most accurate and realistic presentation Each DVD disc may have a variety of audio output possible, thanks to digital audio technology. However, options.
Before Operation (Cont’d) Parental Control Area Code Enter the code of a country/area whose standards were Rating used to rate the DVD video disc, referring to the list Movies on DVDs may contain scenes not suitable for (See “Area Code List”, page 27.). children.
Operation with DVD, Video CD and Audio CD Playing a DVD, Video CD and Audio CD Exchanging discs during playback Press DISC CHANGE on the front panel during play- Playback Setup VCD2.0 VCD1.1 back to open the disc tray. Press DISC SKIP to rotate the disc trays to the Turn on the TV and select the video input source desired position.
Operation with DVD, Video CD and Audio CD (Cont’d) General Features Slow Motion VCD2.0 VCD1.1 1 Press SLOW during playback. Note The player will enter SLOW mode. 2 Use the SLOW to select the required speed: Unless stated otherwise, all operations described use 1/16, 1/8, 1/4 or...
Operation with DVD, Video CD and Audio CD (Cont’d) General Features (cont’d) Time Search 0:16:57 - : - - : - - Repeat VCD2.0 VCD1.1 The Time Search function allows you to start playing at any elapsed time location on the disc. TRACK DISC CHAPT...
Operation with DVD, Video CD and Audio CD (Cont’d) General Features (cont’d) Special DVD Features VCD2.0 VCD1.1 Marker Search Checking the contents of DVD Video discs: Menus MARKER SEARCH DVDs may contain menus that allow you to access spe- You can start playback from a memorized point. Up to cial features.
Page 23
Programmed Playback with Video CD and Audio CD Programmed Playback with Video CD Repeat Programmed Tracks/All and Audio CD 1 To repeat the track currently playing, press REPEAT. The Repeat Track icon appears on the TV screen. Note 2 To repeat all tracks on the program list, press On a Video CD with PBC, you must set PBC to Off on the REPEAT two times.
3 To cancel Repeat mode, press REPEAT repeatedly until required in order to download MP3 files and music the Repeat Off icon appears on the menu screen. from the Internet. TOSHIBA cannot grant such permission. Permission should always be sought from the copyright owner.
Operation with JPEG Disc Moving to another File Viewing a JPEG disc > JPEG Press SKIP once during viewing to This DVD Player can play discs with JPEG files on it. advance to the next file or to the previous file. Make sure the resolution of the JPEG files is less than 2 mega pixels (2M).
Programmed Playback with MP3 or JPEG Disc Programmed Playback with MP3 or Note JPEG Disc The programmed tracks/files are cleared when the JPEG power is turned off or the disc is removed. Program allows you to store your favorite tracks/files (or files) for a particular disc in the player memory.
Additional Information Last Condition Memory VCD1.1 This player memorizes the last condition for the last disc you have watched. Settings remain in memory even if you remove the disc from the player or switch off the player. If you load a disc that has its settings memo- rized, the latest stop position is automatically recalled.
Troubleshooting Check the following guide for the possible cause of a problem before contacting service. Symptom Cause Correction The power cord is disconnected. Plug the power cord into the wall outlet No power. securely. The power is on, but No disc is inserted. Insert a disc.
Page 29
Language Code List Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu” (See page 13). Code Language Code Language Code Language Code Language 6565 Afar 7079 Faroese 7678 Lingala 8375 Slovak 6566 Abkhazian 7082 French 7679...
Area Code List Enter the appropriate code number for the initial setting “Area Code” (See page 15). Code Area Code Area Code Area Code Area Andorra Eritrea Saint Lucia Seychelles United Arab Emirates Spain Liechtenstein Sudan Afghanistan Ethiopia Sri Lanka Sweden Antigua and Barbuda Finland...
Specifications General Power requirements AC 120V , 60 Hz Power consumption Dimensions (approx.) 430 X 79.9 X 410 mm (16.9 x 3.2 x 16.2 inches) (w x h x d) Mass (approx.) 5.1 kg (12.3 lbs) Operating temperature 5˚C to 35˚C (41˚F to 95˚F) Operating humidity 5 % to 90 % System...
LIMITED WARRANTY DVD VIDEO PLAYER Toshiba America Consumer Products, Inc. (“TACP”), Toshiba Hawaii (“THI”) and Toshiba Canada Limited (“TCL”) make the follow- ing limited warranties. These limited warranties extend to original purchaser or any person receiving this set as a gift from the orig- inal purchaser and to no other purchaser or transferee.
Page 33
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and forward this completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate” their warranty. Product must be purchased from an Authorized Canadian Dealer. Products purchased in the U.S.A. and used in Canada are not covered by these warranties.
Page 34
DVD PLAYER OWNER’S MANUAL MODEL : SD-3815 Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely. 1-33...
Safety Precautions FCC WARNING: This equipment may generate or use radio CAUTION frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifi- RISK OF ELECTRIC SHOCK DO NOT OPEN cations are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an CAUTION: TO REDUCE THE RISK unauthorized change or modification is made.
IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND 15. Attachments INSTRUCTIONS IN THIS OWNER’S MANUAL AND THOSE Only use attachments/accessories specified by the manufacturer. MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR 16. Accessories FUTURE REFERENCE. Use only with the cart, stand, tripod, bracket, or This set has been designed and manufactured to assure personal safety.
Before Use Playable Discs Disc-related terms Title (DVD only) The main film content or accompanying feature content DVD Video or additional feature content, or music album. (8 cm / 12 cm disc) Each title is assigned a title reference number enabling Video CD (VCD) you to locate it easily.
Before Use (Cont’d) Precautions Storing discs After playing, store the disc in its case. Handling the unit Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct sun- When shipping the unit light, as there may be a considerable temperature build- The original shipping carton and packing materials...
Front Panel and Display Window ON/STANDBY PLAY ( Switches the player ON and OFF. Starts playback. OPEN/CLOSE ( ON/STANDBY indicator Opens or closes the disc tray. Lights red when the player is in Standby mode (off). 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 STOP ( (left/right/up/down) Stops playback.
Remote Control POWER OPEN/CLOSE ( Switches DVD Player ON and OFF. Opens and closes the disc tray. ZOOM GUI DISPLAY Enlarges video image. Accesses on-screen display E.A.M. SETUP Selects sound mode during disc Accesses or closes setup menu. playback. TOP MENU MENU Displays the Title menu of the disc if Accesses menu on a DVD disc.
Rear Panel OPTICAL (Digital audio out jack) Connect to digital (optical) audio equipment. COAXIAL (Digital audio out jack) Connect to digital (coaxial) audio equipment. ANALOG AUDIO OUT (Left/Right) 1, 2 Connect to an amplifier, receiver or stereo system. AC Power Cord Plug into the power source.
Connections Progressive Scan (ColorStream ® pro) connection Tips If your television is a high-definition or “digital ready” Depending on your TV and other equipment you wish television, you may take advantage of the DVD to connect, there are various ways you could connect Player’s progressive scan output for the highest the player.
Connections (Cont’d) Connecting to Optional Equipment Rear of DVD player Connecting to an amplifier equipped with two channel analog stereo or Dolby Surround Connect the Left and Right AUDIO OUT jacks on the DVD Player to the audio left and right in jacks on your amplifier, receiver or stereo system, using the supplied audio cables (A).
Before Operation General Explanation Repeat mode Icons Repeat Title This manual gives basic instructions for operating the TITLE DVD Player. Some DVDs require specific operation or Repeat Chapter CHAPT allow only limited operation during playback. When this Repeat Track (non-PBC Video CDs TRACK occurs, the symbol appears on the TV screen, indi-...
Before Operation (Cont’d) Initial Settings Picture TV Aspect You can install your own Personal Preferences. 4:3 Letterbox: Select when a standard 4:3 TV is con- Initial Settings General Operation nected. Displays theatrical images with masking bars above and below the picture. Press SETUP.
Before Operation (Cont’d) Sound Dynamic Range Control (DRC) With the DVD format, you can hear a program’s sound- Digital Audio Output track in the most accurate and realistic presentation Each DVD disc may have a variety of audio output possible, thanks to digital audio technology. However, options.
Before Operation (Cont’d) Parental Control Area Code Enter the code of a country/area whose standards were Rating used to rate the DVD video disc, referring to the list Movies on DVDs may contain scenes not suitable for (See “Area Code List”, page 27.). children.
Operation with DVD, Video CD and Audio CD Playing a DVD, Video CD and Audio CD Exchanging discs during playback Press DISC CHANGE on the front panel during play- Playback Setup VCD2.0 VCD1.1 back to open the disc tray. Press DISC SKIP to rotate the disc trays to the Turn on the TV and select the video input source desired position.
Operation with DVD, Video CD and Audio CD (Cont’d) General Features Slow Motion VCD2.0 VCD1.1 1 Press SLOW during playback. Note The player will enter SLOW mode. 2 Use the SLOW to select the required speed: Unless stated otherwise, all operations described use 1/16, 1/8, 1/4 or...
Operation with DVD, Video CD and Audio CD (Cont’d) General Features (cont’d) Time Search 0:16:57 - : - - : - - Repeat VCD2.0 VCD1.1 The Time Search function allows you to start playing at any elapsed time location on the disc. TRACK DISC CHAPT...
Operation with DVD, Video CD and Audio CD (Cont’d) General Features (cont’d) Special DVD Features Marker Search VCD2.0 VCD1.1 Checking the contents of DVD Video discs: Menus MARKER SEARCH DVDs may contain menus that allow you to access spe- You can start playback from a memorized point. Up to cial features.
Programmed Playback with Video CD and Audio CD Programmed Playback with Video CD Repeat Programmed Tracks/All and Audio CD 1 To repeat the track currently playing, press REPEAT. The Repeat Track icon appears on the TV screen. Note 2 To repeat all tracks on the program list, press On a Video CD with PBC, you must set PBC to Off on the REPEAT two times.
3 To cancel Repeat mode, press REPEAT repeatedly until required in order to download MP3 files and music the Repeat Off icon appears on the menu screen. from the Internet. TOSHIBA cannot grant such permission. Permission should always be sought from the copyright owner.
Operation with JPEG Disc Moving to another File Viewing a JPEG disc > JPEG Press SKIP once during viewing to This DVD Player can play discs with JPEG files on it. advance to the next file or to the previous file. Make sure the resolution of the JPEG files is less than 2 mega pixels (2M).
Programmed Playback with MP3 or JPEG Disc Programmed Playback with MP3 or Note JPEG Disc The programmed tracks/files are cleared when the JPEG power is turned off or the disc is removed. Program allows you to store your favorite tracks/files (or files) for a particular disc in the player memory.
Additional Information Last Condition Memory VCD1.1 This player memorizes the last condition for the last disc you have watched. Settings remain in memory even if you remove the disc from the player or switch off the player. If you load a disc that has its settings memo- rized, the latest stop position is automatically recalled.
Troubleshooting Check the following guide for the possible cause of a problem before contacting service. Symptom Cause Correction The power cord is disconnected. Plug the power cord into the wall outlet No power. securely. No disc is inserted. Insert a disc. (Check that the DVD or, The power is on, but the DVD player does audio CD indicator in the display...
Language Code List Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu” (See page 13). Code Language Code Language Code Language Code Language 6565 Afar 7079 Faroese 7678 Lingala 8375 Slovak 6566 Abkhazian 7082 French 7679...
Area Code List Enter the appropriate code number for the initial setting “Area Code” (See page 15). Code Area Code Area Code Area Code Area Andorra Eritrea Saint Lucia Seychelles United Arab Emirates Spain Liechtenstein Sudan Afghanistan Ethiopia Sri Lanka Sweden Antigua and Barbuda Finland...
Specifications General Power requirements AC 120V , 60 Hz Power consumption Dimensions (approx.) 430 X 79.9 X 410 mm (16.9 x 3.2 x 16.2 inches) (w x h x d) Mass (approx.) 5.1 kg (12.3 lbs) Operating temperature 5˚C to 35˚C (41˚F to 95˚F) Operating humidity 5 % to 90 % System...
LIMITED WARRANTY DVD VIDEO PLAYER Toshiba America Consumer Products, Inc. (“TACP”), Toshiba Hawaii (“THI”) and Toshiba Canada Limited (“TCL”) make the follow- ing limited warranties. These limited warranties extend to original purchaser or any person receiving this set as a gift from the orig- inal purchaser and to no other purchaser or transferee.
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and forward this completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate” their warranty. Product must be purchased from an Authorized Canadian Dealer. Products purchased in the U.S.A. and used in Canada are not covered by these warranties.
Page 64
PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY, SUBJECT : X-RADIATION NEVER PERFORM CUSTOMIZED INSTALLATIONS WITHOUT MANUFAC- 1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PER- TURER’S APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT ONLY SONNEL COVER THE SUBJECT OF X-RADIATION.
SERVICING PRECAUTIONS CAUTION : Before servicing the DVD covered by this service Electrostatically Sensitive (ES) Devices data and its supplements and ADDENDUMS, read and fol- Some semiconductor (solid state) devices can be damaged low the SAFETY PRECAUTIONS. NOTE : if unforeseen cir- easily by static electricity.
Page 66
SECTION 2 CABINET & MAIN CHASSIS CONTENTS EXPLODED VIEWS ........................2-2 1. Cabinet and Main Frame Section ...................2-2 2. Deck Mechanism Section......................2-3 3. Packing Accessory Section ....................2-5...
ELECTRICAL TROUBLESHOOTING GUIDE 1. Power(SMPS) Circuit No 5V_D No FLD or 5V_A . Is 5.2VA section working? Is 5.2VA section working? (Is the POWER CTL at Pin6 High/low?) Is oscillation present at the Are D109, L103 open? Base of Q108? No 5.2VA.
2. µ-COM Circuit A. No Power POWER ON Do “Hello” appear at FLD? Is P3901 connected normally? Reconnect it. Check power. (Refer to power) If power is Does Logo appear normal on the screen? Is P3901 Pin 7, 8, 9 normal? Refer to Front Part The waveform on 3, 5, 7 pin of IC503...
Page 74
B. Audio abnormal C. Video abnormal AUDIO ABNORMAL VIDEO ABNORMAL Check Audio jack. Check Video jack. YES (If OK) YES (If OK) Refer to Audio part. Refer to Video part. YES (If OK) YES (If OK) Refer to Decoder part. Refer to PANTERA part.
Page 75
E. Picture abnormal PICTURE ABNORMAL Check the disc. Refer to Servo part If OK Check DSP YES (If OK) Check PANTERA YES (If OK) Replace B/D F. Disc Error DISC ERROR Check Disc YES (If OK) Refer to Servo part YES (If OK) Replace B/D...
Page 76
3. PANTERA Circuit Power is on Does Logo appear Check power & clock. on the screen? Does the Check CD/DVD DSP output moving picture of the DVD Disc Is PANTERA play on the screen data signal normal? signal. normally? Check CD/DVD DSP output Is error signal normal? signal.
4. Front Circuit (Digitron & key) START Power on. Is oscillation of Check Power. LED ON? X901 normal? Check waveform Is Digitron on normally? Replace IC902. of IC901 Pin 7. Do all the Is waveform of IC901 Check waveform buttons work Pin 20 normal? of IC901 Pin 15.
5. RF/Servo Circuit CHECK POINT(General) Does signal goes "High" to IC201 Pin186 when the power is on? Does signal pulse Check "2.PANTERA Part". input to IC201 Pins 53, 54 when the powe is on? Does Replace X201 or IC206 33.8688MHz clock input (30MHz clock defect) to IC201 Pin 63? Replace IC201...
Page 79
No disc .Power on Check loading Part. Push Pick-up to inner track to Does tray open or close? the end by hand. Does DECK assembly is defective. PMD03 Pin 6 change (Limit sw) high to low? Pressing the open/close key repeatedly, check the voltage of IC2M1 check PANTERA Part.
Page 80
DISC IN OPEN/CLOSE Fig.3. FOCUS ERROR waveform Check Check IC2A1 Pin 47,50,51,52 the focus error moving the FOCUS ON? lens up and down. in DVD Mode (IC2A1 Pin 39) IC201 no output : Pick-up is defective. Does the TTL level change at IC201 Replace IC201.
Page 81
CHECK A Fig.5. RF waveform Check RF Eye-Pattern. No signal: Pick-up is defective Check IC2A1 Pins 47, 50, 51, 52. RF : 1.5-1.6V(Q2A6 collector) Does the sawtooth waveform emit See the eye-pattern vivid? Does the 1.6V emit? Replace IC2A1. at IC2A1 Pin 36? Replace IC201.
CIRCUIT DIAGRAM NOTE : 1. Shaded( ) parts are critical for safety. Replace only with specified part number. 1. POWER(SMPS) CIRCUIT DIAGRAM 2. Voltages are DC-measured with a digital voltmeter during Play mode. Oscillation abnormal Digitron no Power 8V line dead No Power 3.3V line dead.
3. DRIVE & RF CIRCUIT DIAGRAM DVD laser CD laser not operate not operate Tray Loading Speed control Focus Servo fail Turntable not operate Tracking Servo fail Turn table speed control Servo fail Actuator spindle sled not operate Focus Servo Loop Sled Servo Loop Tracking Servo Loop Spindle Servo Loop...
Page 91
4. PANTERA CIRCUIT DIAGRAM No Power 1.8V System not operate Not memoried setup No Power on menu Audiuo DAC Interface 9 13 8 System not working or Digitron not display. Y/Pb/Pr(Component) CVBS WAVEFORM Y.c(S-VHS) Audio L/R OUT OPTICAL/COAXITAL OUT 3-23 3-24...
• WAVEFORMS IC2A1 Pin 42, Focus Error IC2A1 Pin 41 IC2A1 Pin 41 IC501 Pin 114 TURN(+)(-) Signal from µ-com TURN(+)(-) from Motor Drive Tracking Error VBR TRACKING Error Component Y Forward turn IC2A1 Pin 57, IC201 Pin 88, SLED Drive(FMO) IC2A1 Pin42, Focus Error(in Focus Search) TURN(+)(-) from Motor Drive Sensor 1 (disc position)
Page 93
5. MEMORY CIRCUIT DIAGRAM Program download fail Digitron all not display and system not operate Not memoried setup Menu Turntable not operating Pick-up not initial operating “No Disc” display Disc number detect error Tray not closed WAVEFORM Tray not open/close 3-27 3-28...
Page 98
MODE MODE MODE MODE LEVEL(V) LEVEL(V) LEVEL(V) LEVEL(V) PIN NO. PIN NO. PIN NO. PIN NO. D E I V E & R F 2.08 2.4V 8.01 I C 2 A 1 2.15 2.4V 2.16 2.16 2.4V 1.636 3.1V 2.4V 7.96 2.5~3.7 2.4V...
3. SMPS P.C.BOARD 4. TIMER P.C.BOARD LOCATION GUIDE LOCATION GUIDE NOTES) Warning NOTES) Parts that are shaded are critical NOTES) With respect to risk of fire or NOTES) electricial shock. 5. KEY P.C.BOARD LOCATION GUIDE 3-43 3-44...
Page 102
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 103
BASE ASSEMBLY, DPM3 TRAY -SH 79098784 3041R-0061B BASE ASSEMBLY, SLED-DAMPER(DVD-CD R 79096037 3041R-0068B BASE ASSEMBLY, DPM3 MAIN -SH 79096097 6871R-5103A PWB(PCB) ASSEMBLY,TO, DMB6000 SH TOSHIBA K 79096042 3501RF4033B BOARD ASSEMBLY, DMB6022N HA1UTT 79096101 6885R-0650E SUB PWB(PCB) ASSEMBL, DMB6022N HA1CTT TOSH 79096095 6871R-5095A...
Page 104
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 105
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 106
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 107
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 108
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 109
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 110
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 111
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 112
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 113
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 114
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 115
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 116
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 117
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 118
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 119
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 120
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 122
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 123
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 124
BASE ASSEMBLY, DPM3 TRAY -SH 79098784 3041R-0061B BASE ASSEMBLY, SLED-DAMPER(DVD-CD R 79096037 3041R-0068B BASE ASSEMBLY, DPM3 MAIN -SH 79096097 6871R-5103A PWB(PCB) ASSEMBLY,TO, DMB6000 SH TOSHIBA K 79096042 3501RF4033B BOARD ASSEMBLY, DMB6022N HA1UTT 79096025 6885R-0650D SUB PWB(PCB) ASSEMBL, DMB6022N HA1UTT TOSH 79096095 6871R-5095A...
Page 125
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 126
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 127
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 128
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 129
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 130
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 131
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 132
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 133
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 134
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 135
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 136
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 137
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 138
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 139
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 140
(yyyy/mm, Not include "/") PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4 Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 142
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 143
BASE ASSEMBLY, DPM3 TRAY -SH 79098784 3041R-0061B BASE ASSEMBLY, SLED-DAMPER(DVD-CD R 79096037 3041R-0068B BASE ASSEMBLY, DPM3 MAIN -SH 79096097 6871R-5103A PWB(PCB) ASSEMBLY,TO, DMB6000 SH TOSHIBA K 79096042 3501RF4033B BOARD ASSEMBLY, DMB6022N HA1UTT 79096267 6885R-0650F SUB PWB(PCB) ASSEMBL, DMB6022N HA1UTTA TOS 79096095 6871R-5095A...
Page 144
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 145
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 146
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 147
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 148
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 149
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 150
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 151
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 152
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 153
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 154
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 155
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 156
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 157
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 158
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 159
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 160
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 162
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 163
79098784 3041R-0061B BASE ASSEMBLY , SLED-DAMPER(DVD-CD R 79096037 3041R-0068B BASE ASSEMBLY , DPM3 MAIN -SH 79096097 6871R-5103A PWB(PCB) ASSEMBLY,TO , DMB6000 SH TOSHIBA K 79096109 3501RF4033A BOARD ASSEMBLY , DMB6024N A46A 79096115 6885R-0650C SUB PWB(PCB) ASSEMBL , DMB6024N HA1UTT TOSH...
Page 164
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 165
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 166
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 167
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 168
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 169
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 170
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 171
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 172
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 173
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 174
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 175
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 176
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 177
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)
Page 178
PRICE UNIT CODE <N, (1.0)> 1: USD, 2: JPY, 3: STG, 4: OTHERS (<- Fill in Unit name at "C6" cell in case of "4" ) Location No. TOSHIBA Part No. Vendor's Part No. Description Reference No. AN, 8 (*1)