Advertisement
1. Assemble and mount the camera
1. Attach the camera to its stand. Ensure the stand's screw post is fully seated in the camera's threaded
mount.
2. Tighten the locking nut on the stand's threaded post.
3. If using wireless connectivity, attach the antenna to the camera. Orient the antenna vertically and
tighten the knurled connector.
4. If mounting the camera to a vertical or overhead surface, use the mounting holes on the base plate
along with screws that are suitable for the mounting surface.
5. Connect the Power Transformer wire to the Power Connector on the camera back. At this time
DO NOT plug the power transformer in.
IMPORTANT: In order for the camera to be placed in the wired mode, the Ethernet cable must be
connected first, then power applied. Likewise in order for the camera to be placed in the wireless
mode, ensure the Ethernet cable is NOT connected, then apply power.
6. Refer to the diagram below, and determine which configuration applies. After the configuration wiring
is complete, plug the Power Transformer into a non-switchable power outlet.
7. Refer to the configurations below, then follow the directions on the right.
3. Enroll or edit the camera(s) in AlarmNet Direct
You will need the following information:
AlarmNet Direct account with user name and password.
Customer account number for the AlarmNet communicator or "Video Services Only" account.
MAC ID for each camera. The MAC ID is on the box and the camera back.
Dealers can enroll the camera and set up a Total Connect account for their customers by
visiting the AlarmNet Direct website:
https://services.alarmnet.com/AlarmNetDirect/
Go to the online help and;
For customers with no AlarmNet accounts – follow the procedure for "
Services Only Account
."
For customers with an existing "Video Only" account – just add the new camera.
For customers with an existing AlarmNet GSM or Internet communicator account –
ensure the account number is green (registered) and the Has Remote Service Capabilities icon is
present. Then just add the new camera.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the
equipment.
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been
type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a
residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Ê800-09425V1JŠ
800-09425V1 1/12 Rev. B
2. Power and configure wireless security
If you have Configuration #1 – Connect each camera to the router using an Ethernet
cable. Ensure power is applied. The camera installation is DONE.
If you have Configuration #2 – Ensure power is applied. Complete all the steps below.
If you have Configuration #3 – You must attach the optional Honeywell WAP Wireless
Access Point to the router, and ensure power is applied. Then complete all the steps
below.
NOTES:
When setting up a wireless configuration in very large buildings or buildings with dense
If using more than one wireless camera, each must be configured for wireless security.
Ensure your router is configured for DHCP. If you are unsure, access the router's
Configuring Wireless Security:
When initially powered up, the camera and WAP use the same default AES key and
encryption parameters. You should create a new AES key to ensure your wireless devices
are associated with your WAP. To create a new AES key, please perform the steps below.
1. Ensure an Ethernet cable is not connected to the camera, then plug the camera's Power
2. Press and hold the WPS button on the router or WAP Wireless Access Point for
3. Within
4. Allow up to 45 seconds for the WPS to complete, then verify successful wireless security
5. Repeat the steps above for each camera.
NETWORK LED Indicator
BLINKING AMBER
STEADY AMBER
NOTE: If the camera is being used in a wireless mode and the Reset button on the back of
the camera is used, you must reconfigure wireless security for that camera.
When the camera is set up and the customer's Total Connect account is established,
they can view their video by visiting:
The cameras are now ready for customer use.
Have the customer log into their Total Connect account to view the video.
Creating a Video
If their PC does not have QuickTime® and Flash® player, you will be prompted to install or
update these applications.
If any of the cameras were mounted upside down, there is a setting to upright the image.
At this time the location of each camera can be adjusted for the desired view.
When adding, editing, or deleting a camera, the customer will receive email notification.
For detailed camera operation refer to the Total Connect online help guide.
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
CLASS B DIGITAL DEVICE STATEMENT
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est
soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute
interference reçue y compris les interferences causant une reception indésirable.
Honeywell is a registered trademark of Honeywell International Inc.
Flash is a registered trademark of Adobe Systems Incorporated, registered in the U.S. and other countries.
QuickTime is a registered trademark of Apple Inc., registered in the U.S. and other countries.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright 2011 Honeywell International Inc.
www.honeywell.com/security
walls, wireless communications may be marginal. It is best to first configure the system
in the same room. Then upon successful configuration, place each camera in the
desired location. Verify that all cameras exhibit good communications as indicated by a
STEADY GREEN Power LED and a Network LED that occasionally BLINKS GREEN.
configuration page and set it for DHCP (refer to the router's manual). If you are using a
wireless router that supports WPS instead of the Honeywell WAP, please refer to the
manufacturer's guide to setup wireless security.
Transformer into an outlet. Wait for the Power indicator to light steady.
3
seconds, then RELEASE.
1
minute, click and RELEASE the WPS button on the camera.
as indicated by a STEADY GREEN Power LED and a Network LED that occasionally
BLINKS GREEN. If these indicators are present you are done.
Unsuccessful Wireless Security Indications
Comment / Action
Camera is searching for a WPS router or the Honeywell
WAP Wireless Access Point.
Try the following:
1. Allow up to 45 seconds for the Network LED to turn
BLINKING GREEN.
2. If it remains BLINKING AMBER, repeat steps 1 thru
4 in the
WPS configuration was unsuccessful.
Repeat steps 1 thru 4 in the
Security
http://www.mytotalconnect.com/
TRADEMARKS
WARRANTY
For the latest warranty information go to:
http://www.security.honeywell.com/hsc/resources/wa/
Configuring Wireless Security
procedure.
Configuring Wireless
procedure above.
The last 6 digits of the MAC ID is
also on the back of the camera.
Hide quick links:
Advertisement
