Advertisement
Quick Links
Advertisement
Summary of Contents for Lightolier ILSLMHUB
- Page 2 This manual is for informational use only and is subject to change without notice. Lightolier Controls assumes no responsibility or liability for any claims resulting from errors or inaccuracies that may appear in this manual. Version as of: July 8, 2008 Document: 85-6330A0 Lytemode Network Powered Hub User’s Guide...
-
Page 3: Table Of Contents
’ YTEMODE ETWORK OWERED UIDE Important Safeguards When using electrical equipment, basic safety precautions should always be followed including the following: a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS. b) Do not use outdoors. c) Do not mount near gas or electric heaters. d) Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. -
Page 4: Customer Service
’ USTOMER ERVICE YTEMODE ETWORK OWERED UIDE Customer Service Technical and Sales assistance for Lytemode products are available worldwide. Phone: +1-800-526-2731 (In the United States and Canada) +1-214-647-7880 (Worldwide) -
Page 5: Lytemode System Overview
Master Station from the wall, and without the need for a computer. Lytemode Master Stations are compatible with both Lightolier Controls Insulated Gate Bipolar Transistor (IGBT) Dimming Cabinets as well as Silicon Controlled Rectifier (SCR) Dimming Panels. -
Page 6: Lytemode Ils Network Powered Hub Overview
UIDE Lytemode Network Powered Hub Overview The Lytemode Network Powered Hub (ILSLMHUB) provides DC Power across the Lytemode ILS Network for the purpose of powering Master Stations, Remotes, and Interfaces. The Network Powered Hub provides 1.5 amps each for four separate, electrically isolated Lytemode Network circuits. The unit is equipped with separate compartments for Line Voltage wiring connections and Low Voltage wiring connections. -
Page 7: Device Power Requirements
’ YTEMODE ETWORK OWERED VERVIEW YTEMODE ETWORK OWERED UIDE Device Power Requirements The following chart provides power requirements for Lytemode ILS devices. Master Stations ILSCL125ES 103mA Each ILSCL165ES 116mA Each ILSCL85ES 72mA Each ILSCL45ES 59mA Each ILSCL6MMES 20mA Each ILSCLTS 350mA Each ILSDMX45ES 60mA Each... -
Page 8: Installation
’ NSTALLATION YTEMODE ETWORK OWERED UIDE Installation The Network Powered Hub can be wall-mounted or rack-mounted using the included mounting brackets. Knock-out holes in the unit’s housing can be used to route power wiring and network cables as required. Installing the Unit To install: Step 1. - Page 9 ’ NSTALLATION YTEMODE ETWORK OWERED UIDE Step 6. As required, remove knock-out hole covers and route power input wires and Lytemode ILS Network cables as shown in Figure 3. Note: The Lytemode ILS Network consists of a single CAT5e cable connecting all Lytemode ILS devices in a daisy-chain configuration.
-
Page 10: Specifications
’ PECIFICATIONS YTEMODE ETWORK OWERED UIDE Specifications Electrical: • Input Power: 110-240VAC, 50-60Hz, 3.2 A, 1 Phase • Output Power: 24VDC, 1.5 A per output (x 4 Separate Outputs) • Number of Outputs: 4 • Temperature: - Storage: -25° to 85° C - Operating: 0°... - Page 11 THREE YEAR LIMITED WARRANTY The Philips Controls product, when properly installed and under normal conditions of use (without overload, abuse or alteration), is warranted to you, the original user, for a period of three years form the date of original retail purchase, to be free from defects in materials and workmanship.